JBM electronics C-130 User manual

Page -1-
Copyright ©2007 JBM Electronics, Inc.
C-130
Quick Start Guide

Page -2-
Copyright ©2007 JBM Electronics, Inc.
Table of Contents
Quick Start Guide ............................................................................................................... 3
Unpacking Instructions................................................................................................... 3
Preparation...................................................................................................................... 3
Accessing the Graphical Management Interface ............................................................ 4
Step 1: Connect PC to JBM Gateway..................................................................... 4
Step 2: Setup PC IP Address................................................................................... 5
Step 3: Access JBM Webserver.............................................................................. 8
Step 4: Log into the Graphical Administration Utility (GAU)............................... 8
Cellular Card Configuration ........................................................................................... 9
Step 2: Set the Userid, password and APN........................................................... 12
Step 3: Save and Apply the Configuration ........................................................... 12
Verify Cellular Connectivity......................................................................................... 12
Cellular Connectivity Troubleshooting......................................................................... 13
Cellular Reception ................................................................................................ 13
Verifying IP Connectivity..................................................................................... 14
Minimal Reception................................................................................................ 15
Authentication Issues............................................................................................ 15
JBM Technical Support ........................................................................................ 16
SPECIFCATIONS............................................................................................ 17
FCC Compliance Statement.............................................................................................. 18
Information To The User.............................................................................................. 18
Warranty ........................................................................................................................... 19
Extended Warranty Program......................................................................................... 19

Page -3-
Copyright ©2007 JBM Electronics, Inc.
Quick Start Guide
Unpacking Instructions
1. Unpack the C130.
2. Verify the following components are enclosed (Figure A).
3. If any items are missing, please contact JBM at 1-800-489-7781.
Preparation
1. Verify that you have one of the following, supported cellular cards:
1xRTT/1xEVDO
Audiovox/UTSStarcom: 5740
Kyocera: KPC-650
Novatel: S/V-620, S/V-720
Sierra Wireless: 555, 580, 5220
GPRS/Edge/HSDPA
Sierra Wireless: 750, 775, 860
Sony Ericsson: GC-83

Page -4-
Copyright ©2007 JBM Electronics, Inc.
2. Using the instructions that accompanied the card, verify that the card is
properly activated and functioning correctly prior to installing the car into
the JBM Gateway:
•Install the software that came with the aircard on a laptop.
•Install the aircard into the laptop.
•Follow the carrier provided procedures to properly activate the
card, and unlock the card if necessary.
•Using the browser on the laptop insure that you are able to
browse the Internet.
3. Resolve any and all signal/reception related issues with the aircard
installed in the laptop before installing the card into the JBM Gateway.
4. Gently, insert the Aircard into the PCMCIA slot. Be sure it is firmly
seated.
5. Attach power supply connector to C130 and connect power supply plug to
an AC power outlet.
6. Verify the PWR (yellow) LED is lit to indicate that the unit is receiving
power.
7. Establish access to the unit through Gateway Administration Utility.
Accessing the Graphical Management Interface
Step 1: Connect PC to JBM Gateway
METHOD – 1 ETH0: (Straight Ethernet Port)
•Connect a crossover CAT-5 Ethernet cable between the local PC and the
JBM unit’s ETH0. Verify the link LED is lit. (Straight cable from a
HUB/Switch).
METHOD 2 - ETH1:(Crossed-over Ethernet Port)
•Connect straight CAT-5 Ethernet cable between the local PC and the JBM
unit’s ETH1. Verify the link LED is lit. (Crossover cable for
HUB/Switch).
Port Cable Device
Straight (ETH0) Straight HUB or Switch
Straight (ETH0) Crossed PC
Crossed (ETH1) Straight PC
Crossed (ETH1) Crossed HUB or Switch

Page -5-
Copyright ©2007 JBM Electronics, Inc.
Note: This example shows cabling to a PC. The link LED is not lit for ETH1.
Without a link LED lit either Method 1 must be used or the cabling must be
checked.
Step 2: Setup PC IP Address
Set the PC’s IP Address by going to control panel and selecting network connections, the
screen below will appear:
•Right Click “Local Area Connection” and select “Properties” (as shown to the
left).

Page -6-
Copyright ©2007 JBM Electronics, Inc.
NOTE: The screens and instructions displayed are based on Windows XP. Your system
may be different. If you have any problems contact your system admin.
•Scroll down to the bottom of the following items and select “Internet Protocol
(TCP/IP)” (as shown to the left).
METHOD 1: PC to ETH0
•Select “Use the following IP address” and fill in the blank fields with the
information below:
•IP address: 192.168.0.2
•Subnet mask: 255.255.255.0
•Default gatewa:y 192.168.0.1
•Preferred DNS: 192.168.0.1
•Click “OK”
•The previous screen will appear Click “OK”

Page -7-
Copyright ©2007 JBM Electronics, Inc.
METHOD 2: PC to ETH1
•Select “Use the following IP address” and fill in the blank fields with the
information below:
•IP address: 192.168.1.2
•Subnet mask: 255.255.255.0
•Default gatewa:y 192.168.1.1
•Preferred DNS: 192.168.1.1
•Click “OK”
•The previous screen will appear Click “OK”
Verify that the IP change was accepted or acquired on the PC.
Select “Start>Run on your desktop ” Type “cmd” Click “OK”
•Type “ipconfig” <Enter>

Page -8-
Copyright ©2007 JBM Electronics, Inc.
•METHOD 1 should display an IP of 192.168.0.2
•METHOD 2 should display an IP of 192.168.1.2
Step 3: Access JBM Webserver
•Open a web browser and enter the following in the address bar:
METHOD 1: http://192.168.0.1:10000/
METHOD 2: http://192.168.1.1:10000/
Step 4: Log into the Graphical Administration Utility (GAU)
JBMgateway Login Instructions
•User Name enter: jbmadmin ( lowercase letters)
•For Password enter: six digit serial number of unit (lowercase letters)
Upon successfully logging in you will be rewarded with the following screen:
•At this point, you are connected to the Gateway. You can now configure
the unit to meet your needs.

Page -9-
Copyright ©2007 JBM Electronics, Inc.
Cellular Card Configuration
Your JBM Gateway is able to detect many cellular cards, but others must still be
configured manually. If you are using either one of the older 1xRTT/CDMA cards, or a
GPRS/EDGE/HSDPA card that requires the use of a userid, password, and APN, you will
need to configure your car manually, as covered in the next section.
If you are using any of these cards you will need to work through this section:
GPRS/Edge/HSDPA
Sierra Wireless: 750, 775, 860
Sony Ericsson: GC-83
If you are using one of the newer 1xRTT/1xEVDO, USB Serial based cards, your JBM
gateway has probably automatically detected, configured, and activated your cellular
connection for you, so you can skip this section and proceed to the next section to verify
your cellular connectivity.
If you are using any of these cards you can skip this section:
1xRTT/1xEVDO
Audiovox/UTSStarcom: 5740
Kyocera: KPC-650
Novatel: S/V-620, S/V-720
Sierra Wireless: 555, 580, 5220
Navigate through the GAU menus to the screen Cellular Configuration Screen shown
below:

Page -10-
Copyright ©2007 JBM Electronics, Inc.
Step 1: Cellular Carrier Selection
•Select the cellular carrier you are using from the drop-down menu.