JBM electronics C120F User manual

C120F / C300
Quick Start
Guide

C120/C300
Quick Start Guide 2 08/29/2008
Unpacking Instructions.............................................................................................3
Preparation C120 ......................................................................................................5
Preparation C300 ......................................................................................................6
Accessing the Graphical Management Interface......................................................7
Step 1: Connect PC to JBM Gateway.......................................................................7
Step 2: Setup PC IP Address.....................................................................................8
METHOD 1: PC to ETH0......................................................................................10
METHOD 2: PC to ETH1......................................................................................11
Step 3: Access JBM Webserver...............................................................................13
JBMgateway Login Instructions.............................................................................13
Cellular Card Configuration...................................................................................16
Step 1: Cellular Carrier Selection...........................................................................17
Step 2: Set the Userid, password and APN.............................................................20
Step 3: Apply the Configuration.............................................................................20
Verify Cellular Connectivity...................................................................................21
Note: .....................................................................................................................21
Cellular Connectivity Troubleshooting ..................................................................22
Cellular Reception...................................................................................................22
Verifying IP Connectivity........................................................................................23
Minimal Reception ..................................................................................................24
Authentication Issues ..............................................................................................25
JBM Technical Support..........................................................................................26
FCC Compliance Statement.....................................................................28
Information To The User ........................................................................................28
Warranty...................................................................................................29
Extended Warranty Program.................................................................................29

C120/C300
Quick Start Guide 3 08/29/2008
Unpacking Instructions
1. Unpack the JBM unit.
2. Verify the following components are enclosed for the C120 (Figure A).

C120/C300
Quick Start Guide 4 08/29/2008
3. Verify the following components are enclosed for the C300 (Figure B).
4. If any items are missing, please contact JBM at 1-800-489-7781.

C120/C300
Quick Start Guide 5 08/29/2008
Preparation C120
1. Verify that you have one of the following, supported cellular cards:
Alltel PC 5750
Huawei EC360
Huawei 620 ( Non-US GSM )
Kyocera KPC 650
Kyocera 680 (req. caddy. Not supported w/VMB5000 caddy)
Novatel EX720 (req. caddy)
Novatel 620
Novatel 640 (req. caddy)
Novatel S720 (Sprint)
Novatel V720 (Verizon)
Novatel EX720 (req. caddy)
Novatel XU870 (req. caddy)
Novatel X950D (gsm) (req. caddy)
Option GT Max 3.5 HSDPA
Option GT Max 3.5 HSUPA
Pantech PX500
Sierra Wireless Aircard 555
Sierra Wireless Aircard 580
Sierra Wireless Aircard 595
Sierra Wireless Aircard 597E (cdma) ( req. caddy )
Sierra Wireless Aircard 850 (Non-US GSM)
Sierra Wireless Aircard 860 (AT&T)
Sierra Wireless Aircard 875 (AT&T)
Sierra Wireless Aircard 881 (AT&T)
Sierra Wireless Aircard 5220
Sony GC82/GC83/GC85
Sony Ericson PC300 (gsm)
Verizon PC5740
Verizon PC5750
Note: "req. caddy" denotes an aircard that is a PCI Expressbus card. PCI Express cards
are smaller than a standard PCMCIA adapter and require an appropriate adapter to work
in a standard PCMCIA CardBus Slot. Unfortunately, not all manufacturers provide
adapters that are 100% compatible. If you are using one of the PCI Express cards listed
here, and your JBM router does not automatically recognize your card when it is inserted,
please try a different PCMCIA Adapter Caddy before contacting JBM Technical Support.
We continually add support for new Data Cards to the Gateways. If your Data Card is not
supported, please contact us so we can provide an updated driver.
2. Using the instructions that accompanied the card, verify that the card is properly
activated and functioning correctly prior to installing the car into the JBM
Gateway:

C120/C300
Quick Start Guide 6 08/29/2008
•Install the software that came with the aircard on a laptop.
•Install the aircard into the laptop.
•Follow the carrier provided procedures to properly activate the card, and
unlock the card if necessary.
•Using the browser on the laptop insure that you are able to browse the
Internet.
3. Resolve any and all signal/reception related issues with the aircard installed in the
laptop before installing the card into the JBM Gateway.
4. Gently, insert the Aircard into the PCMCIA slot. Be sure it is firmly seated.
5. Attach power supply connector to C120 and connect power supply plug to an AC
power outlet.
6. Verify the PWR (yellow) LED is lit to indicate that the unit is receiving power.
7. Establish access to the unit through Gateway Administration Utility.
Preparation C300
1. Verify with your service provider that the SIM installed in the C300 is activated.
2. Connect one of the antennas to the “Main” antenna port on the front of the C300.
3. Attach power supply connector to C120 and connect power supply plug to an AC
power outlet.
4. Verify the PWR (yellow) LED is lit to indicate that the unit is receiving power.
5. Establish access to the unit through Gateway Administration Utility.

C120/C300
Quick Start Guide 7 08/29/2008
Accessing the Graphical Management Interface
Step 1: Connect PC to JBM Gateway
METHOD – 1 ETH0: (Straight Ethernet Port)
Connect a crossover CAT-5 Ethernet cable between the local PC and the JBM unit’s
ETH0. Verify the link LED is lit. (Straight cable from a HUB/Switch).
METHOD 2 - ETH1:(Crossed-over Ethernet Port)
Connect straight CAT-5 Ethernet cable between the local PC and the JBM unit’s ETH1.
Verify the link LED is lit. (Crossover cable for HUB/Switch).
Port Cable Device
Straight (ETH0) Straight HUB or Switch
Straight (ETH0) Crossed PC
Crossed (ETH1) Straight PC
Crossed (ETH1) Crossed HUB or Switch
Note: This example shows cabling to a PC. The link LED is not lit for ETH1.
Without a link LED lit either Method 1 must be used or the cabling must be
checked.

C120/C300
Quick Start Guide 8 08/29/2008
Step 2: Setup PC IP Address
Set the PC’s IP Address by going to control panel and selecting network connections, the
screen below will appear:
•Right Click “Local Area Connection” and select “Properties” (as shown to the
left).
NOTE: The screens and instructions displayed are based on Windows XP. Your
system may be different. If you have any problems contact your system admin.

C120/C300
Quick Start Guide 9 08/29/2008
•Scroll down to the bottom of the following items and select “Internet Protocol
(TCP/IP)” (as shown to the left).

C120/C300
Quick Start Guide 10 08/29/2008
METHOD 1: PC to ETH0
•Select “Use the following IP address” and fill in the blank fields with the
information below:
•IP address: 192.168.0.2
•Subnet mask: 255.255.255.0
•Default gateway: 192.168.0.1
•Preferred DNS: 192.168.0.1
•Click “OK”
•The previous screen will appear Click “OK”