JC LAB Bimc-01NS User manual

Monocular Microscope
Bimc-01NS
Ver.1.0.1
®
I N T E R N A T I O N A L
OPERATION MANUAL
JC LAB Microscope - JAPAN
www.jc-lab.jp - [e-mail]

INDEX
1.0 Copyright Page 1 - 3
2.0 Microscope at a Glance Page 4
3.0 Introducon Page 5
4.0 Unpacking and Assembly Page 5
5.0 Microscope Accessories Page 6 - 7
6.0 Using the Microscope Page 8
7.0 Maintenance Page 9
8.0 Electrics Page 10
9.0 Recycling and Revcovery Page 10

Copyright
© 2012 by JC LAB Corporaon. All rights reserved. Under the copyright law,
this manual cannot be reproduced in any form without the prior wrien
permission of JC LAB. No patent liability is assumed, with respect to the use of
the informaon contained herein.
First edion Feb. 2012
Disclaimer
This manual has been validated and reviewed of accuracy. The instrucons
and descripons it contains are accurate for your wi-microscope at the me
of this manual’s producon. However, succeeding wi-microscope and
manuals are subject to change without noce. JC LAB assumes no lability for
damages incurred directly or indirectly from error, omissions or discrepancies
between the wi-microscope and the manual.
Trademarks
◆JC CAM logo are registered trademarks of JC LAB Corporaon.
◆Wi-Fi is registered trademark of Wi-Fi Alliance.
◆USB, the USB logo and USB interface are trademarks or registered
trademarks of USB Licensing LLC.
Other trademarks are registered trademarks not listed above may be used in
this manual.
EU Declaraon of Conformity
This Product is carrying the CE-Mark in accordance with the related
European Direcves. Responsible for CE-Marking is JC LAB Japan
GmbH, 5 Chome-12-13 Serigaya Kōnan-ku, Yokohama-shi,
Kanagawaken 233-000, Japan. The complete and ocial EU
Declaraon of Conformity can be found on JC LAB website
hp://www.jc-lab.jp on the internet.
1.0 Copyright
Page 1

Disposing of the Microscope and It’s Baeries
◆Discard this Microscope in accordance with applicable laws and
regulaons. For further informaon, contact your government.
◆Some models contains rechargeable baeries. Aer repeated use, the
baeries will nally lose their ability to hold a charge and you will need to
replace them. Under certain applicable laws and regulaon, it may be
illegal to dispose of old baeries by replacing them in the trash.
◆Please be kind to our shared environment. Check with your local
government authority for details regarding where to recycle old baeries
or how to dispose of them properly.
Informaon for Wireless Devices
Page 2
Wireless Devices and your Health
Wireless Products, like other radio devices, emit radio frequency
electromagnec energy. The level of energy emied by Wireless products
however is far much less than the electromagnec energy emied by wire
device like for example mobile phones.
Because Wireless products operate within the guidelines found in radio
frequency safety standards and recommendaons, JC LAB believes Wireless
products is safe for use by consumers. These standards and recommendaons
reect the consensus of scienc community and result from deliberaons of
panels and commiees of sciensts who connually review and interpret the
extensive research literature.
In some situaons or environments, the use of Wireless Products may be
restricted by the proprietor of the building or responsible representaves of
the organizaon. These situaons may for example includes:
◆Using the Wireless products equipment on board of airplanes, or
◆In any other environment where the risk of interference to other devices
or services is perceived or idened as harmful.
If you are uncertain of the policy that applies on the use of wireless devices in
a specic organizaon or environment (e.g. airports), you are encouraged to
ask for authorizaon to use the Wireless device prior turning on the
equipment.
1.0 Copyright

Canada — Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
Operaon is subject to the following two condions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may case undesired operaon on this device.
The Term “IC” before the equipment cercaon number only signies that
the Industry Canada technical specicaons were met.
USA-Federal Communicaons Commission (FCC)
Page 3
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part of FCC Rules. These limits are designed
to provide reasonable protecon against harmful interference in a residenal
installaon.
JC LAB Support
If you require any addional help your devices or if you are having problems
operang devices, you may need to contact JC LAB for addional technical
assistance.
Before you call
Some problem you experience may be related to soware, apps or the
operang system so it is importance that you invesgate other sources of
assistance rst.
Before contacng JC LAB, try the following:
Review troubleshoong secons in the documentaon supplied withyour
soware and/or peripheral devices.
If problem occurs when you are running in your computer systems, consult the
soware document for troubleshoong suggesons and consider calling the
system company’s technical support department for assistance.
Consult the reseller or dealer from where you purchased your devices and
soware— they are your best resource for current informaon and support.
JC LAB technical support
If you are sll unable to solve the problems and suspect that it is hardware
related, visit JC LAB technical support website
hp://www.jc-lab.jp
1.0 Copyright

Page 4
Note: Microscope features may vary based on your locaon, language,
carrier, and model number. Accessory parts may incur addional fees.
Contact your local distributor to ensure the features.
1. Monocular Head
2. Stand
3. Nosepiece
4. Objecve Lens
5. Aachable Mechanical Stage
6. Stage
7. Condenser Knob
8. Fine Adjustment Knob
9. Coarse Adjustment Knob
10. Light Intensity Adjust
11. Power Plug (DC 5V)
12. On/O Switch
13. Viewing Head adjust
14. Iris Turning
15. Y-axis movement
16. X-axis movement
17. Light Source Cover
1
Microscope at a Glance
2
9
5 & 6
8
15 & 16
13
3 & 4
11
7 & 14
17
10
2.0 Microscope at a Glance
BIMC-01NS
12

This microscope is a scienc precision instrument designed to last for many
years with a minimum of maintenance. It is built to high opcal and
mechanical standards and to withstand daily classroom and laboratory use.
JC LAB reminds you that this manual contains important informaon on safety
and maintenance, and that it must therefore be made accessible to the
instrument users. JC LAB declines any responsibility deriving from instrument
use that does not comply with this manual.
Page 5
4.1 The microscope is housed in a moulded Styrofoam container. Remove
the tape from the edge of the container and li the top half of the container.
Take some care to avoid that the opcal items (objecves and eyepieces) fall
out and get damaged. Li the microscope from the container and put it on a
stable desk.
4.2 The objecves are assembled on the microscope. If removed the
objecves from the microscope then insert them into the microscope
nosepiece in the order from the lowest magnicaon to the highest, in a
clockwise direcon from the rear.
Do not touch with bare hands opcal surfaces such as lenses, lters or
glasses. Traces of grease or other residuals may deteriorate the nal
image quality and corrode the opcs surface in a short me.
3.0 Introducon
4.0 Unpacking and Assembly

5.0 Microscope Accessories
Page 6
The BIMC-A03A-W3 is known around the globe for their ease-of-use and adaptability to a number of applicaons.
The JC Cam’s unique “All In One Box” design, assures each user that this camera can t almost any microscope
whether it’s for Educaonal, Industrial or Clinical use. The JC CAM allows you to convert your digital images into
documentaon les for professional prinng. It is equipped with a USB 3.0 and Wi-Fi for data transfer, ensuring a
good response me.
Image Sensor:
SONY IMX412 CMOS
Exposure Mode:
Roller shuer exposure
Maximum Resoluon:
4000 x 3000 (12,000,000 pixels)
Sensor Opcal Format:
1/2.3”
Pixel Size:
1.55μm x 1.55μm
ISO Sensivity:
Equivalent to 100 - 12800
Exposure Time:
10us - 333ms, Real-me Auto and Manual adjustment
White Balance:
Real-me auto and manual RB adjustment
Preview resoluon (USB, HDMI & 5G Wi-Fi):
30FPS@4000x3000, 3840x2160, 2592x1944, 1920x1080
Spectral Characteriscs:
380 - 650nm
Record Format:
Snapshot
Format: JPG, BMP, PNG, TIFF
Resoluon: 4000x3000, 3840x2160, 2592x1944, 1920x1080
Record
Format: AVI, MP4 le
Resoluon: 30fps@1920x1080 (AVI), 1920x1080, 1600x1200
(MP4)
Supporng protocol:
5G Wi-Fi IEEE 802.11ac
Power Supply:
DC 5V 2A
Support System:
Microso® Windows 10/11 or more, IOS 11.0 or more, Android
7.0 or more
Computer Conguraon:
CPU: i5 10th generaon or later version, Memory: 16GB or more,
Hard drive: 512GB or more, Graphics card: Core graphics,
Network card: 10/100/1000M adapve
*Standard packing: Main Body + 0.5x Eyepiece + 30mm &
23.2mm Adapter + Soware CD + USB + HDMI Cable
*All of our microscopes are covered by a 5 year warranty on mechanical
components and 2 year warranty on electrical components
Live stream with mulple devices

Page 7
Stage Micrometer for Microscope
Calibraon with NIST cercaon Lens Cleaning Tissue for slide cleaning
5.0 Microscope Accessories
BIMC-S09A TOO-155E
MiniPC for JC Cam series Wi
eyepiece to screen on the TV
BIMC-MIPC06
Digital Drying Cabinet, Cap. 60L
CHD-60
Slide Folder, hold 20pcs of slide
MCS-SL01A

Page 8
6.0 Using the Microscope
6.1 Turn the observaon head to a comfortable posion for observaon
6.2 Ensure that the specimen is centred over the stage opening. Lock the
specimen slide on the aachable mechanical stage using the two slide clamp
6.3 Insert the plug of the cable into the power socket on the back of the
microscope to charge it and turn the switch to the charge
mode (on the right side of the main body).
6.4 Rotate the coarse focusing knob to bring the slide into
focus with the 4X objecve. Adjust the ne focusing knob to get the image
sharp and clear.
6.5 Adjust the aperture of the iris diaphragm to set the numerical aperture of
the illuminator, thus controlling image contrast and resoluon.
6.6 Turn the nosepiece to choose the objecve you need.

Page 9
7.0 Maintenance
7.1 Always think about
- The following environment is required: Indoor temperature: 0-40°C,
Maximum relave humidity: 85 % (not condensing)
- Keep the microscope away from dust and shocks while in use.
- Turn o the light immediately aer use.
- Use a so lens ssue to clean the opcs aer use.
- Only if needed, use a cloth moistened with water and a mild detergent,
rinsing with water and drying immediately with a lint-free cloth.
- Aer use, cover the microscope with the included dust-cover, and keep it
in a dry and clean place.
7.2 Do not!
-Wipe the surface of any opcal items with your hands. Fingerprints can
damage the opcs.
- Use solvents, neither on the microscope, nor on the opcs.
- Disassemble objecve or eyepieces to aempt to clean them.
- Mishandle or impose unnecessary force on the microscope.
- Clean the unit with volale solvents or abrasive cleaners.
- Aempt to service the microscope yourself.
7.3 How to change the lamp
Before changing the lamp, you must switch it o, pull the plug out of the
electrical socket. To avoid being burnt, wait unl the lamp has cooled down.
Unscrew the condensing lens above the lamp. Then remove the old lamp and
replace it with a new one. Replace the condensing lens
7.4 If you need to send the microscope to JC LAB for maintenance, please
use the original packaging

Page 10
8.0 Electrics
Universal Power: 220 V, 50/60 Hz, DC 5V 2A
Lamp: 5W Cold Light s-LED
Fuse: T1A
9.0 Recycling and Recovery
Art.13 Dlsg 25 july 005 N°151. “According to direcves 2002/95/EC, 2002/96/
EC and 2003/108/EC relang to the reducon in the use of hazardous
substances in electrical and electronic equipment and waste disposal.”
The basket symbol on equipment or on its box indicates that the
product at the end of its useful life should be collected separately from
other waste. The separate collecon of this equipment at the end of its
lifeme is organized and managed by the producer. The user will have to
contact the manufacturer and follow the rules that he adopted for end-
of-life equipment collecon. The collecon of the equipment for
recycling, treatment and environmentally compable disposal, helps to
prevent possible adverse eects on the environment and health and
promotes reuse and/or recycling of materials of the equipment. Improper
disposal of the product involves the applicaon of administrave
penales as provided by the laws in force.