JC LAB BIMC-12A User manual

User manual
Bimc-12A

Contents
Copyright Page 1 - 3
Microscope at a Glance Page 4
Microscope Accessories Page 5- 6
Working Instrucon Page 7-8

Copyright
© 2012 by JC LAB Corporaon. All rights reserved. Under the copyright law,
this manual cannot be reproduced in any form without the prior wrien
permission of JC LAB. No patent liability is assumed, with respect to the use of
the informaon contained herein.
First edion Feb. 2012
Disclaimer
This manual has been validated and reviewed of accuracy. The instrucons
and descripons it contains are accurate for your wi-microscope at the me
of this manual’s producon. However, succeeding wi-microscope and
manuals are subject to change without noce. JC LAB assumes no lability for
damages incurred directly or indirectly from error, omissions or discrepancies
between the wi-microscope and the manual.
Trademarks
◆JC CAM logo are registered trademarks of JC LAB Corporaon.
◆Wi-Fi is registered trademark of Wi-Fi Alliance.
◆USB, the USB logo and USB interface are trademarks or registered
trademarks of USB Licensing LLC.
Other trademarks are registered trademarks not listed above may be used in
this manual.
EU Declaraon of Conformity
This Product is carrying the CE-Mark in accordance with the related
European Direcves. Responsible for CE-Marking is JC LAB Japan
GmbH, 5 Chome-12-13 Serigaya Kōnan-ku, Yokohama-shi,
Kanagawaken 233-000, Japan. The complete and ocial EU
Declaraon of Conformity can be found on JC LAB website
hp://www.jc-lab.jp on the internet.
Page 1

Disposing of the Microscope and It’s Baeries
◆Discard this Microscope in accordance with applicable laws and
regulaons. For further informaon, contact your government.
◆Some models contains rechargeable baeries. Aer repeated use, the
baeries will nally lose their ability to hold a charge and you will need to
replace them. Under certain applicable laws and regulaon, it may be
illegal to dispose of old baeries by replacing them in the trash.
◆Please be kind to our shared environment. Check with your local
government authority for details regarding where to recycle old baeries
or how to dispose of them properly.
Informaon for Wireless Devices
Page 2
Wireless Devices and your Health
Wireless Products, like other radio devices, emit radio frequency
electromagnec energy. The level of energy emied by Wireless products
however is far much less than the electromagnec energy emied by wire
device like for example mobile phones.
Because Wireless products operate within the guidelines found in radio
frequency safety standards and recommendaons, JC LAB believes Wireless
products is safe for use by consumers. These standards and recommendaons
reect the consensus of scienc community and result from deliberaons of
panels and commiees of sciensts who connually review and interpret the
extensive research literature.
In some situaons or environments, the use of Wireless Products may be
restricted by the proprietor of the building or responsible representaves of
the organizaon. These situaons may for example includes:
◆Using the Wireless products equipment on board of airplanes, or
◆In any other environment where the risk of interference to other devices
or services is perceived or idened as harmful.
If you are uncertain of the policy that applies on the use of wireless devices in
a specic organizaon or environment (e.g. airports), you are encouraged to
ask for authorizaon to use the Wireless device prior turning on the
equipment.

Canada — Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
Operaon is subject to the following two condions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may case undesired operaon on this device.
The Term “IC” before the equipment cercaon number only signies that
the Industry Canada technical specicaons were met.
USA-Federal Communicaons Commission (FCC)
Page 3
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part of FCC Rules. These limits are designed
to provide reasonable protecon against harmful interference in a residenal
installaon.
JC LAB Support
If you require any addional help your devices or if you are having problems
operang devices, you may need to contact JC LAB for addional technical
assistance.
Before you call
Some problem you experience may be related to soware, apps or the
operang system so it is importance that you invesgate other sources of
assistance rst.
Before contacng JC LAB, try the following:
Review troubleshoong secons in the documentaon supplied withyour
soware and/or peripheral devices.
If problem occurs when you are running in your computer systems, consult the
soware document for troubleshoong suggesons and consider calling the
system company’s technical support department for assistance.
Consult the reseller or dealer from where you purchased your devices and
soware— they are your best resource for current informaon and support.
JC LAB technical support
If you are sll unable to solve the problems and suspect that it is hardware
related, visit JC LAB technical support website
hp://www.jc-lab.jp

Microscope at a Glance
Page 4
Note: Microscope features may vary based on your locaon, language,
carrier, and model number. Accessory parts may incur addional fees.
Contact your local distributor to ensure the features.
1. Monocular Head
2. Stand
3. Nosepiece
4. Objecve Lens
5. Stage Clip
6. Mechanical Stage
7. Condenser Knob
8. Fine Adjustment Knob
9. Coarse Adjustment Knob
10. Light Intensity Adjust
11. Power Plug
12. Fuse Box
13. On/O Switch
14. Viewing adjust
15. Condenser Turning
16. Y-axis movement
17. X-axis movement
18. Light Source Cover
1
2
9
5 & 6
8
16 & 17
14
3 & 4
11, 12 & 13
7 & 15
18
10

Accessories
Page 5
WiFi Eyepiece for viewing and capture photo/video in the microscope.

Accessories
Page 6
Stage Micrometer for Microscope Calibraon with NIST cercaon
Lens Cleaning Tissue for slide cleaning

Working Instrucon
Page 7
Place Slide
Place the slide on the mechanical stage.
First open the clip, then put the slide
into it. And then move it into center.
2) Choosing Objecve
Lens
First, you need to using low power
Objecve lens to viewing object.
From 4x --> 10x--> 40x-->100x
3) Adjustment knob
Use a hand to turn the adjustment
knob. Coarse adjustment suitable for
low power objecve lens (e.g. 4x and
10x). Fine adjustment suitable for high
power objecve lens (e.g. 40x and 100x).
Turn it unl image clear.

Working Instrucon
Page 8
4) Turning Viewing Head
using your eye to view eyepiece, make
sure the eye become comfortable.
5) Adjust Condenser
First, using your hand to turn the
condenser when the light intensity is
too high or the objects is to detail.
6) Turn O
Aer using the microscope, adjust the
light intensity too dark. Then press the
On/OFF switch to turn o the
microscope.