Jebao UFP-1000 User manual

UV Fountain pump
User manual
Model: UFP-1000, UFP-2000
WARNING
Please read the operating instructions and familiarize yourself with the
equipment before placing it in service .Correct and safe use of the system
requires strict compliance with the safety instructions .For safety reasons
children and young people under 16 years of age, as well as people that
cannot recognize potential hazards, or people that are not familiar with these
instructions, may not use this device.
CAUTION
UFP series is UV clarify equipment which can be combined. It contains water
pump and one piece of UV lamp, Any damage on the equipment or unmerited
operation will bring dangerous s radiation to the skin and eyes. So if there is
any damage of the equipment , it can’t be used any more ,This equipment is
not intend for use by person (including children) with reduced physical ,
sensory of mental capabilities ,or lack of experience and knowledge ,unless
they have been given supervision or instruction concerning use of the
equipment by a person responsible for their safety. The equipment should be
placed out of reach to children .For the consideration of security, people
under 16 years old and those who can’t identify danger or grasp the
instruction can’t use the equipment.
1. This equipment should be placed under the water. Be sure the equipment
is submerged completely in the water and the depth should not be
greater than 0.5M
2. When the water is not enough to submerge the equipment, please never
connect power of the equipment to avoid running without water and
cause damage.
3. As the UV lamp is made of quartz glass, please avoid drop of it or wallop
on it.
4. Before all parts are installed completely ,the equipment can’t be plugged
in
5. If there is any damage on the power cable ,UV lamp or shell ,the
equipment can’t be used. And it should be discarded as useless.
6. Please make sure that the electrical voltage, frequency used are
consistent with the indication on the label of the equipment.
7. When installing the equipment, the installation regulation of pond pump
should be followed.
8. The equipment should be earthed .And the professional person should
check the condition of earthed. For the considered of safety, we advise
customer to install leakage protector.
9. Pull the connecting cable is forbidden. And please keep the connecting
cable away from heat, greasiness or sharpness.
10. When the pump have any unusual noise, please unplug to check the
reason.
11. When know the frost is coming, please move away filter to avoid frost
crack.
12. The dirtiness on the quartz glass tube will influence the effect of the
equipment, please clean the quartz glass tube in time.
13. When the body sell is blocked with the sands and rubbish, it is possible to
destroy the quartz glass tube and water pump .so please add the filter
sponge to the inlet of the water. And the sponge should be cleaned timely
(once a month ).
14. UV is harmful to the eyes and skin. Please do not watch UV directly or let
the skin approach to UV.
15. When install or repair this equipment, the electrical source of the
equipment must be switched off.

INSTRUCTION
1. This equipment built-in filter sponge, filter material boxed, UV lamp
and water pump. This equipment adopt reasonable water channel,
suitable for both indoor, outside pond garden, aquatic breeding, clean
water sterilization and water fountains.
2. Through the working of water pump, water flow from the filter cover
to filter sponge, and then to the UV lamp. Inside of the UV lamp, the
harmful bacteria and algae will be killed. Then the water flow to
outside finally.
3. The UV lamp was designed as a closed device, no UV will scattering.
And UV light 253.7nm will kill the harmful bacteria and algae to keep a
good condition of water.
TECHNICAL PARAMETER
Model
Voltage
I or Power
UV Power
H-Max
Q-Max
UFP-1000
110-120V60H
z
0.28A
9W
1.6M
1000L/H
UFP-2000
110-120V60H
z
0.68A
13W
2.0M
2000L/H
UFP-1000
220-240V50H
z
25W
9W
1.6M
1000L/H
UFP-2000
220-240V50H
z
50W
11W
2.0M
2000L/H
INSTALLATION AND MAINTENANCE
Please switched off the electrical power when you clean the inside or change
the UV pump. When clean the inside or change the UV lamp, please take
below part list as your reference.
INSTALLATION
MAINTENANCE
Maintenance for filter sponge and filter material:
1. First ,anti-clockwise direction take off the fountain set, open the two clips
on the side of the filter basket, then you can open the filter basket.
2. Take out the filter sponge and filter material boxes , clean and/or change
these.(suggest clean the filter sponge every week)
3. if the bio ball is seriously polluted, it should be washed in the water in the
pool,to preservation of microbial and biochemical properties on biochemical
balls.
MAINTENANCE FOR UV-LAMP
1. Take out the UV lamp for the unit, unload the screw and take out lamp
holder.
2. Open the screw, turn the lamp holder and take out lamp holder
components.


3. Remove the nut at the glass tube, take out the glass tube, allow UV light
assembly and light bulb to cool and dry completely before handling. Once
cool and dry, grip the base of the bulb with a dry cloth and gently pull the
bulb from the assembly unit(do not pull on the bulb by gripping the grass
element)
4. Slide new bulb into place until properly seated. Do not test UV light until
the filter has been completely reassembled.
5. If you need to clean the quartz glass tube, please extract the glass tube ,
remove possible calcareous deposits on the tube using a suitable product.
Then reassemble all the parts making sure that the o-rings and gaskets are
correctly placed.
MAINTENANCE FOR PUMP
1. Take out the pump, turn impeller room in anti-clockwise direction till the
block position, then you can separate the impeller room and pump body.
2. Take out the magnet rotor , clean all the parts with clean water and
suitable brush.
STORAGE IN WINTER
1. Take out the equipment from water.
2. Clean the equipment thoroughly.
3. Check the parts and conditions of the equipment.
4. Keep this equipment in a area that free from frost. And in a container that
with clean.
EASILY BROKEN PARTS
1. UV tube
2. Filter materials (bio-ball, gravel, filter sponge).
TROUBLE SHOOTING
Trouble
Season
Solution
Water pump not work
●No power
●Burn
●Impeller block
●Running without water
●Plug in
●Change water pump
●Clean the blocks
●Submersible the equipment under water
,then plug in again.
Water pump noisy
●Something blocked in the impeller
room or shaft broken
●Open the water pump and clean the blocks
●Change the shaft or shaft cover
●Shaft or shaft cover wear
Water pump lack of
water
●Impeller broken or water flow valve
closed
●Equipment inlet blocked or water pump
inlet blocked
●Lower voltage than requested
●Change the impeller set or open the water
flow valve
●Clean the blocks
●Use suitable voltage
UV lamp not work
●No power
●UV tube broken
●Connection of the UV tube not good
●Plug in
●Change UV tube
●Re-place the UV tube
DISPOSAL:
Do not dispose this product as unsorted municipal waste. Collection of such waste
separately for special treatment is necessary. This product must not be disposed
together with the domestic waste. This product has to be disposed at an authorized
place for recycling of electrical and electronic appliances. By collecting and recycling
waste, you help save natural resources, and make sure the product is disposed in an
environmental friendly and healthy way.
Jebao Co.,Ltd
Tongmao Industrical Park, Dongsheng, Zhongshan, Guangdong. China.
Email:[email protected] Website: www.jebao.com
Tel:[phone]/20 Fax:[phone]