Jenn-Air JBS7524BS0 User manual

INSTALLATION INSTRUCTIONS
24" (59.5 CM) STEAM AND CONVECTION
BUILT-INOVEN
INSTRUCTIONS D'INSTALLATION
e= e=
FOUR ELECTRIQUEENCASTREA CONVECTION
ETA,VAPEUR24" (59,5 CM)
TableofContents/Table des mati@res
BUILT-IN OVEN SAFETY ............................................................... 1
INSTALLATION REQUIREMENTS ................................................ 2
Tools and Parts ............................................................................ 2
Location Requirements ................................................................ 2
Minimum Dimensions ................................................................... 3
Product Dimensions ..................................................................... 4
Electrical Requirements ............................................................... 4
INSTALLATION INSTRUCTIONS .................................................. 5
Install the Oven
(24" [59.5 cm] Installation Only) ................................................... 5
Install the Oven
(27" [68.2 cm] or 30" [75.6 cm] Installation Only) ........................ 6
Complete Installation ................................................................... 7
SI_CURITI_ DU FOUR ENCASTRI_ ................................................ 8
EXIGENCES D'INSTALLATION ..................................................... 9
Outils et pieces ............................................................................. 9
Exigences d'emplacement ........................................................... 9
Dimensions minimales ............................................................... 10
Dimensions du produit ............................................................... 11
Specifications electriques .......................................................... 11
INSTRUCTIONS D'INSTALLATION ............................................. 12
Installation du four
(Installation de 24" [59,5 cm] uniquement) ................................ 12
Installation du four
(Installation de 27" [68,2 cm] ou 30" [75,6 cm] uniquement) .....13
Achever I'installation .................................................................. 15
BUILT-INOVEN SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
iMPORTANT:
Save for local electrical inspector's use.
iMPORTANT :
Aconserver pour consultation par I'inspecteur local des installations 61ectriques.
W10419853A

INSTALLATIONREQUIREMENTS
Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
• Measuring tape • Electric drill
• Pencil • 5/_,,(2 mm) drill bit
• T10 TORX®tscrewdriver
Parts Supplied
All of the following parts are provided, but not all parts will be
used. The cutout opening size will determine which parts you will
use. See the chart following the illustrations of the parts to see
which parts are used for each installation.
A
B
DE
IMPORTANT: Observe all governing codes and ordinances.
• Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance with oven.
• Recessed installation area must provide complete enclosure
around the recessed portion of the oven.
• Grounded electrical supply is required. See "Electrical
Requirements" section.
• Oven support surface must be solid, level and flush with
bottom of cabinet cutout. Floor must be able to support an
oven weight of 111 Ibs (50 kg).
IMPORTANT: To avoid damage to your cabinets, check with
your builder or cabinet supplier to make sure that the
materials used will not discolor, delaminate or sustain other
damage. This oven has been designed in accordance with
the requirements of UL and CSA International and complies
with the maximum allowable wood cabinet temperature of
194°F (90°C).
Undercounter Installation (with cooktop installed above):
Ovens approved for this type of installation have an approval
label located on the top of the oven. Refer to undercounter
installation instructions for cutout dimensions and approved oven
cooktop combinations (a separate sheet).
A. Side brackets (2)
B. Removable extension plates
(shaded piece, 2)
C. 1" TIO screws (6)
D. Narrow side trim panels (2)
E. Wide side trim panels (2)
INSTALLATION
24" (61.0 cm)installation
27" (68.6 cm)installation*
30" (76.2 cm)installation
*Extension plate (B) will have to be
for this installation.
PARTS USED
C
A,C,D
A, B, C, E
removed from side bracket (A)
1-®TORX is a registered trademark of Saturn Fasteners, Inc.
2

Minimum Installation Clearances
For proper installation, the following minimum clearances must exist above and below the cutout opening.
Above Cabinet/Storage Drawer Installation Below Counter Installation
(without cooktop installed above)
A
B
C_
D
E
F
D
AJ,
v
£
E
A. 23_" (60.0 cm) minimum cabinet width
B. 21 z_,,(55.6 cm) minimum cutout width
C. 17_" (45.0 cm) recommended cutout height*
D. ½" (1.2 cm) minimum from top of cutout to bottom of upper
cabinet door or counter
*Will fit cutout height from 173/4'' (45.0 cm) to 177/8'' (45.4 cm).
Minimum Cutout Dimensions
NOTE: Depth dimension may be 213/4" (55.2 cm) with non-flush
receptacle only if the receptacle is located in upper right or upper
left corner. See "Cutout Top View."
213/4" (55.2 cm)*_
26_/4" (66.7 cm) ** 7 "1 / /1/ /1_ /
s I : ;
I ) :- -i '
I ))
E. ½" (1.2 cm) minimum from bottom of cutout to top of lower
cabinet door or drawer
F. 23_"-51 ¼" (60.0-130.0 cm) bottom of cutout to floor
G. Recommended junction box location
*With flush receptacle, or with non-flush receptacle located in
upper right or upper left corner of cutout.
**With non-flush receptacle.
DIM. 24" (59.5 CM) 27" (68.2 CM) 30" (75.6 CM)
INSTALLATION INSTALLATION INSTALLATION
Width 217/8"(55.6 cm) 253/4"(65.4 cm) Min. 253/4"
_+3/le"(4.8 mm) _+3/le"(4.8 mm) (65.4 cm)
Max. 283/4"
(73.0 cm)
Height 173/4"(45.0 cm) for all installations
Depth 213/4"(55.0 cm) with flush receptacle, or with non-flush
receptacle located in far corner;
2@/4" (66.7 cm) with non-flush receptacle

Cutout TopView
l 26!/4.
(66.7 crn)
19%"
_9.7 cm)
A. Oven
B. Non-flush receptacle
C. Flush receptacle
D. Non-flush receptacle located in upper
right or upper left corner
E. Oven door fully open
A. 18" (45.5 cm)
B. 3_/' (0.4cm)
C.Model/serial rating plate (locatedon the oven frame
behind the bottom left side of the oven door)
D. 23 ½" (59.5 cm)
E. 13½"(34.2 cm)
F.21z_,, (55.5 cm)
G. 3 _" (9.5cm)
H. 14_" (35.6 cm)
I. 175_ '' (44.7 cm)
J. 19_" (49.7 cm)
K. 22¼" (51.7 cm)
*Measurements include front facing of oven. Depth measurement
also includes door handle.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
IMPORTANT: The range must be electrically grounded in
accordance with local codes and ordinances, or in the absence of
local codes, with the National Electrical Code, ANSI/NFPA 70 or
Canadian Electrical Code, CSA C22.1.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
• A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is
required. A time-delay fuse or circuit breaker is also
recommended. It is recommended that a separate circuit
serving only this range be provided.
• Check that the outlet provides 120-volt power and is correctly
grounded.
• The wiring diagram is located on the back of the oven in a
clear plastic bag.
NOTE: The metal chassis of the oven must be grounded in order
for the control panel to work. If the metal chassis of the oven is
not grounded, no keypads will operate. Check with a qualified
electrician if you are in doubt as to whether the metal chassis of
the oven is grounded.

INSTALLATIONINSTRUCTIONS
Excessive Weight Hazard
Use two or more people to move and install oven.
Failure to do so can result in back or other injury.
NOTE: For this oven, the door handle may be used for lifting. Do
not use any other portion of the control panel, side brackets, front
frame or trim for lifting.
1. Empty oven of any loose items.
2. Using 2 or more people, slide the oven all the way into the
opening.
3. Center the oven within the opening. Open the oven door.
C
A. Door facing frame
B. Trim panel
C. 1" TIO screws (4)
4. Mark 4 holes (2 on each side) in the door facing frame of the
oven.
5. To avoid damage to the frame while drilling during the next
step, close the door and remove the oven.
6. Drill the 4 holes using 5/64"(2 mm) drill.
Electrical Shock Hazard
Plug into agrounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
7. With the oven near the opening, plug the oven into the
grounded 3-prong outlet.
8. Replace oven in cutout opening.
9. Open the oven door. The holes in the door facing frame
should align with the holes just drilled into the cabinet. Fasten
the microwave oven door facing to the cabinet using four 1"
T10 screws.
10. Proceed to "Complete Installation" section.

llI'he 0
Excessive Weight Hazard
Use two or more people to move and install oven.
Failure to do so can result in back or other injury.
1. Empty oven of any loose contents.
2. For 30" installation, skip this step.
For 27" installation, remove the extension plate from each of
the side brackets by removing the 2 screws.
3. Loosen the middle and rear screws on each side of the oven.
The screws are located at the same height as the door
handle.
4. Place the side bracket over the 2 screws, fitting the screw
heads through the keyholes on the bracket. Then slide the
side bracket down so that the upper portions of the keyholes
rest on the screws.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
FaJJure to folJow these instructions can result in death,
fire, or electrical shock.
7. With the oven near the opening, plug the oven into the
grounded 3 prong outlet.
8. Using 2 or more people, slide oven all the way into the
opening, and center the oven within the opening.
NOTE: The screw holes on the winged ends of both side
brackets (or extension plates for 30" installation) must be fully
over the wood of the wall or cabinet, as shown.
A B C
A. Side bracket
B. Existing screws (middle and rear)
C. Proper side bracket attachment
5. Tighten screws to secure the side bracket to the oven.
6. Repeat steps 4 and 5 on the other side of the oven.
A. Door front facing
B. Screw hole for cabinet attachment
C. Cabinet front
9. Using %4" (2 mm) drill, drill pilot holes into the cabinet through
the screw holes on the side brackets (or extension plates for
30" installation).
10. Install two 1" T10 screws in the pilot holes to secure the oven
in place.
NOTE: To ensure proper side trim panel fitting, do not overtighten
screws.
11. Open oven door.
12. Position the tabular portion of the side trim panel behind the
door facing frame, then firmly push the outside edge of the
trim behind the side bracket, as shown.
6

Exploded View of Panel Placement
A B C
A. Door facing frame
B. Side bracket
C. Side trim panel in place
13. Attach the side trim panel to the door facing frame using two
1" T10 screws.
1=
2.
Check the steam oven by running the steam and convection
bake functions according to the Use and Care Guide.
If the steam oven does not operate:
• Check that a household fuse has not blown, or a circuit
breaker tripped. Replace the fuse or reset the circuit
breaker. If the problem continues, call an electrician.
• Check that the power supply cord is plugged into a
grounded 3 prong outlet.
• See the Use and Care Guide for troubleshooting
information.
Installation is now complete.
Save these Installation Instructions for future use.
If you need Assistance or Service:
Please reference the "Assistance or Service" section of the Use
and Care Guide, or contact the dealer from whom you purchased
your built-in oven.
C
A. Door facing frame
B. Trim panel
C. 1" TIO screws (4)
14. Repeat steps 12 and 13 on other side.

SECURITEDUFOURENCASTRE
Votre securite et celle des autres est tres importante.
Nous donnons de nombreux messages de s_curit_ importants dans ce manuel et sur votre appareil m_nager. Assurez-vous de
toujours lire tous les messages de s_curit_ et de vous y conformer.
Voici le symbole d'alerte de s_curit&
Ce symbole d'alerte de s_curit_ vous signale les dangers potentiels de d_c_s et de blessures graves &vous
et &d'autres.
Tousles messages de s_curit_ suivront le symbole d'alerte de s_curit_ et le mot "DANGER" ou
"AVERTISSEMENT". Ces mots signifient •
Risque possible de d_cbs ou de blessure grave si vous ne
suivez pas imm_diatement les instructions.
Risque possible de d_cbs ou de blessure grave si vous
ne suivez pas les instructions.
Tousles messages de s_curit_ vous diront quel est le danger potentiel et vous disent comment r_duire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.

EXIGENCESD'INSTALLATION
Outils n_cessaires
Rassembler les outils et pieces necessaires avant d'entreprendre
I'installation. Lire et observer les instructions fournies avec
chacun des outils de la liste ci-dessous.
• Metre ruban • Perceuse electrique
• Crayon • Foret de %4" (2 mm)
• Tournevis T10 TORX ®t
Pi_ces fournies
Toutes les pieces suivantes sont fournies, mais elles ne seront
pas toutes utilisees. Les dimensions de I'ouverture
d'encastrement determineront les pieces qui doivent etre
utilisees. Voir le tableau indique apres la liste des pieces pour
savoir quelles pieces utiliser en fonction de chaque installation.
A
B
DE
IMPORTANT : Observer les dispositions de tous les codes et
reglements en vigueur.
• Respecter les dimensions indiquees pour les ouvertures
decouper dans les placards. Oes dimensions tiennent
compte des degagements de separation necessaires pour le
four.
• L'espace d'installation dans un encastrement doit permettre
la formation d'une enceinte complete autour de la partie
encastree du four.
• Une source d'electricite avec liaison & la terre est necessaire.
Voir la section "Specifications electriques".
• La surface de support du four doit etre robuste, horizontale et
en affleurement avec le bas de I'ouverture decoupee dans le
placard. Le plancher doit pouvoir supporter le poids d'un four
de 111 Ib (50 kg).
IMPORTANT •Afin d'eviter d'endommager les placards,
consulter I'installateur ou le fabricant des placards pour
determiner si les materiaux utilises peuvent subir un
changement de couleur, une destratification ou d'autres
dommages. Ce four a ete congu conformement aux
exigences des normes UL et CSA International et respecte la
temperature maximale permise de 194°F (90°C) pour les
placards en bois.
Installation sous un plan de travail (avec table de cuisson
install_e au-dessus) :
Les fours homologues pour ce type d'installation comportent une
etiquette d'homologation placee sur le dessus du four. Consulter
les instructions d'installation pour dessous de plan de travail
pour connaitre les dimensions de I'ouverture a realiser et les
combinaisons approuvees four/table de cuisson (document
distinct).
A. Brides lat#rales (2)
B. Plaques de raccord amovibles (piece gris#e, 2)
C. Vis TIO de 1" (6)
D. Panneaux de garniture lat#rale #troits (2)
E. Panneaux de garniture lat#rale large (2)
INSTALLATION Pli:CES
UTILISEES
Installation de 24" (61 cm) C
Installation de 27" (68,6 cm) A, C, D
Installation de 30" (76,2 cm) A, B, C, E
*Pour cette installation, la plaque de raccord (B) doit etre retiree
du support lateral (A).
1-®TORX est une marque d6pos&e de Saturn Fasteners, Inc.

Distances de d_gagement minimales pour I'installation
Pourune installationcorrecte, lesdistances de degagement minimales suivantes doivent _trerespectees au-dessus et au-dessous de
I'ouverture&decouper.
Installation au-dessus d'un placard/tiroir de Installation sous comptoir
remisage (sans table de cuisson au-dessus)
JJ
==
_=
-< A
C*
1
D
E
F
L
E
i
mm
A. Largeur minimale de placard : 23%" (60 cm)
B. Largeur minimale de I'ouverture : 217/8'' (55,6 cm)
C. Hauteur recommand#e de I'ouverture 17_" (45 cm)*
D. 1A" (1,2 cm) minimum entre le sommet de rouverture et le bas
de la porte du placard mural ou le plan de travail
E. 1/2"(1,2 cm) minimum entre le bas de I'ouverture et le sommet
de la porte du placard inf#rieur ou le tiroir
F. 23%"-511/4 '' (60 -130 cm) entre le bas de I'ouverture et le
plancher
G. Emplacement recommand# pour la bofte de connexion
*Convient & une ouverture avec hauteur comprise entre 173/4"(45 cm) et 177/8"(45,4 cm).
*Avec prise en affleurement, ou avec prise qui n'est pas en
Dimensions minimales de I'ouverture &d_couper
REMARQUE : La profondeur peut _tre de 213/4'' (55,2 cm) avec
une prise qui ne soit pas en affleurement, uniquement si la prise
se trouve & I'angle superieur droit ou superieur gauche• Voir "Vue
du dessus de I'ouverture & decouper".
173/4"
(45,0 cm)
affleurement et qui se trouve & I'angle superieur droit ou
superieur gauche de I'ouverture & decouper.
**Avec prise qui n'est pas en affleurement.
DIMEN- INSTALLATION INSTALLATION INSTALLATION
SION DE 24" DE 27" DE 30"
(59,5 CM) (68,2 CM) (75,6 CM)
Largeur 217/8"(55,6 cm) 253/4"(65,4 cm) Min. 253/4"
_+3/ld' (4,8 mm) _+3/16"(4,8 mm) (65,4 cm)
Max. 283/4''
(73 cm)
Hauteur 173/4'' (45 cm) pour toutes les installations
Profon- 213/4'' (55 cm) avec prise en affleurement, ou avec
deur une prise qui n'est pas en affleurement et qui se
trouve dans un angle eloign6; 261/4'' (66,7 cm) avec
une prise qui n'est pas en affleurement
10