Jenn-Air JES1450CDS0 User manual

INSTALLATIONINSTRUCTIONS
30" (76.0 CM) SLIDE-INELECTRICRANGES
INSTRUCTIONSD'INSTALLATIONDESCUISINIERES
ELECTRIQUESENCASTRABLESDE30" (76,0 CM)
TableofContents/Table des mati@res
RAN GE SAFETY ............................................................................. 2
INSTALLATION REQUIREMENTS ................................................ 3
Tools and Parts ............................................................................ 3
Location Requirements ................................................................ 3
Electrical Requirements - U.S.A. Only ......................................... 6
Electrical Requirements - Canada Only ....................................... 7
INSTALLATION INSTRUCTIONS .................................................. 8
Unpack Range .............................................................................. 8
Install Anti-Tip Bracket ................................................................. 8
Adjust Leveling Legs .................................................................... 9
Level Range ................................................................................ 10
Electrical Connection - U.S.A. Only ........................................... 10
Verify Anti-Tip Bracket is Installed and Engaged ...................... 15
Remove/Replace Drawer ........................................................... 16
Oven Door .................................................................................. 16
Complete Installation ................................................................. 17
SI_CURITI_ DE LA CUISINII_RE ................................................... 19
EXlGENCES D'INSTALLATION ................................................... 20
Outillage et pieces ...................................................................... 20
Exigences d'emplacement ......................................................... 20
Specifications electriques - Canada seulement ........................ 23
INSTRUCTIONS D'INSTALLATION ............................................. 24
Deballage de la cuisiniere .......................................................... 24
Installation de la bride antibasculement .................................... 24
Reglage des pieds de nivellement ............................................. 25
Reglage de I'aplomb de la cuisiniere ......................................... 26
Verifier que la bride antibasculement
est bien installee et engagee ...................................................... 26
Depose et repose du tiroir .......................................................... 27
Porte du four ............................................................................... 27
Achever I'installation .................................................................. 28
iMPORTANT:
Save for local electrical inspector's use.
iMPORTANT :
,&,conserver pour consultation par I'inspecteur local des installations 61ectriques.
W10665255A

RANGESAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Anti-Tip
"" Bracket
Range Foot
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation instructions.
Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
To verify the anti-tip bracket is installed and engaged:
• Slide range forward.
•Look for the anti-tip bracket securely attached to floor or wall.
•Slide range back so rear range foot is under anti-tip bracket.
•See installation instructions for details.
2

INSTALLATIONREQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
• Tape measure • Masking tape
• Flat-blade screwdriver • 1¼.(13 mm) drive ratchet
• Phillips screwdriver • 1¼.(13 mm) nut driver
• Level • 3/8"(10 mm) and 8/16"(8 mm)
nut driver
• Hand or electric drill
• Wrench or pliers • 1/8"(3 mm) drill bit (for wood
floors)
• Marker or pencil • Tin snips or large wire
cutters (for cutting ground
strap if necessary)
Parts supplied
Check that all parts are included.
• 3 - 10-32 hex nuts (attached to terminal block)
• 3- Direct wire lugs
• 2 - #10 x 1%" (4.1 cm) screws (for mounting anti-tip bracket)
• Anti-tip bracket (inside oven cavity)
Anti-tip bracket must be securely mounted to the back wall or
floor. Thickness of flooring may require longer screws to
anchor bracket to subfloor. Longer screws are available from
your local hardware store.
•For model:
JES1450C D
JES1450D
JIS1450CD
JIS1450D
KSEG700E
KSEB900E
KSIB900E
MES8880D
WEE760HOD
IEL730C YKSEG700E
WEC530HOD YKSEB900E
WEE730HOD YKSIB900E
YIEL730C YMES8880D
YWEE730HOD YWEE760HOD
Oven racks 2 3
Parts needed
If using a power supply cord kit:
• A UL listed power supply cord kit marked for use with ranges.
The cord should be rated at 250 volts minimum, 40 amps or
50 amps that is marked for use with nominal 13/8"(3.5 cm)
diameter connection opening and must end in ring terminals
or open-end spade terminals with upturned ends.
• A UL listed strain relief.
Check local codes. Check existing electrical supply. See the
appropriate "Electrical Requirements" section.
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
Optional Parts
To purchase these or any other accessories, please reference the
"Accessories" section of the User Guide for contact information.
•Side Trim Kits:
White - Order Part Number W10677527
Black - Order Part Number W10675026
Stainless Steel - Order Part Number W10675028
Backsplash Kits:
High 6" (15.2 cm) White - Order Part Number W10655448
High 6" (15.2 cm) Black - Order Part Number W10655449
High 6" (15.2 cm) Stainless Steel- Order Part Number
W10655450
IMPORTANT: Observe all governing codes and ordinances.
• It is the installer's responsibility to comply with installation
clearances specified on the model/serial rating plate. The
model/serial rating plate is located behind the oven door on
the top right-hand side of the oven frame.
• The range should be located for convenient use in the
kitchen.
• Recessed installations must provide complete enclosure of
the sides and rear of the range.
• To eliminate the risk of burns or fire by reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
or microwave hood combination that projects horizontally a
minimum of 5" (12.7 cm) beyond the bottom of the cabinets.
• All openings in the wall or floor where range is to be installed
must be sealed.
• Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
• The anti-tip bracket must be installed. To install the anti-tip
bracket shipped with the range, see "Install Anti-Tip Bracket"
section.
• Grounded electrical supply is required. See the appropriate
"Electrical Requirements" section.
• Contact a qualified floor covering installer to check that the
floor covering can withstand at least 200°F (93°C).
• Use an insulated pad or _¼"(0.64 cm) plywood under range if
installing range over carpeting.
IMPORTANT: To avoid damage to your cabinets, check with your
builder or cabinet supplier to make sure that the materials used
will not discolor, delaminate or sustain other damage. This oven
has been designed in accordance with the requirements of UL
and CSA International and complies with the maximum allowable
wood cabinet temperatures of 194°F (90°C).

Mobile Home -Additional Installation Requirements
The installation of this range must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280). When such standard is not
applicable, use the Standard for Manufactured Home
Installations, ANSI A225.1/NFPA 501A or with local codes.
In Canada, the installation of this range must conform with the
current standards CAN/CSA-A240-1atest edition, or with local
codes.
Mobile home installations require:
• When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the standards
listed above.
• Four-wire power supply cord or cable must be used in a
mobile home installation. The appliance wiring will need to be
revised. See "Electrical Connection - U.S.A. Only" section.
Product Dimensions
This manual covers several models. Your model may appear
different from the models depicted. Dimensions given are
maximum dimensions across all models.
Model KSEB900
AC
D
A. 1_" (3.0 cm) height from
cooktop to top of vent
B. 29 z_,,(75.9 cm)
C. Model/serial number plate
(located behind the oven door on
the top right-hand side of the
oven frame)
D. 36" (91.4 cm) height to top of
cooktop edge with leveling legs
screwed all the way in*
E. 28 5_''(71.9 cm) max. depth
from front of console to
back of range.
F. 28 z_,,(73.3 cm) max. depth
from handle to back of
range.
IMPORTANT: Range must be level after installation. Follow the
instructions in the "Level Range" section. Using the cooktop as a
reference for leveling the range is not recommended.
*Range can be raised approximately 1" (2.5 cm) by adjusting
the leveling legs.

Cabinet Dimensions
Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm)
countertop height.
IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood
combination installation instructions for dimensional clearances above the cooktop surface.
Range may be installed next to combustible walls with zero clearance.
NOTE: When installed in a slide-in cutout, the front of oven door may protrude beyond the base cabinet.
Slide-in Cutout
,L
\
A. 18" (45. 7 cm) upper side cabinet to countertop
B. 13" (33 cm) max. upper cabinet depth
C. 30" (76.2 cm) min. opening width
D. For minimum clearance to top of cooktop, see NOTE*.
E.In U.S.A.: 30" (76.2 cm) min. opening width
In Canada: 31" (78.7 cm) min. opening width
EThe shaded area is recommended for installation of grounded
outlet.
G. 13 _" (33.3 cm)
H. 71¼_,,(19.5 cm)
I.4 1_,, (12.2 cm)
J. 3 1¼_,,(9.4 cm) or measurement of L, whichever is greater
K. Cabinet door or hinges should not extend into the cutout.
L. Remaining counter depth should not exceed 2_ "(5.7 cm)
Freestanding cutout
I
!
J
A. 18" (45.7 cm) upper side cabinet to countertop
B. 13" (33 cm) max. upper cabinet depth
C. 30" (76.2 cm) min. opening width
D. For minimum clearance to top of cooktop, see NOTE*.
E.In U.S.A.: 30" (76.2 cm) min. opening width
In Canada: 31" (78.7 cm) min. opening width
EThe shaded area is recommended for installation of grounded
outlet.
G. 13 _" (33.3 cm)
H. 71_,, (19.5 cm)
I. 41_,, (12.2 cm)
J. 31_,, (9.4 cm)
K. Cabinet door or hinges should not extend into the cutout.
*NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet is shielded by not less than 1/4"(0.64 cm) flame retardant
millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020"
(0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet.

Ifcodespermitandaseparategroundwireisused,itis
recommendedthataqualifiedelectricalinstallerdeterminethat
thegroundpathandwiregaugeareinaccordancewithlocal
codes.
Donotuseanextensioncord.
Besurethattheelectricalconnectionandwiresizeareadequate
andinconformancewiththeNationalElectricalCode,ANSI/
NFPA70-latesteditionandalllocalcodesandordinances.
If connecting to a3-wire system:
Local codes may permit the use of a UL listed, 3-wire, 250-volt,
40- or 50-amp range power supply cord (pigtail). This cord
contains 3 copper conductors with ring terminals or open-end
spade terminals with upturned ends, terminating in a NEMA Type
10-50P plug on the supply end. Connectors on the appliance end
must be provided at the point the power supply cord enters the
appliance. This uses a 3-wire receptacle of NEMA Type 10-50R.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
WARNING: Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with a
qualified electrician or service technician if you are in doubt as to
whether the appliance is properly grounded. Do not modify the
power supply cord plug. If it will not fit the outlet, have a proper
outlet installed by a qualified electrician.
Electrical Connection
To properly install your range, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
• Range must be connected to the proper electrical voltage
and frequency as specified on the model/serial number rating
plate. The model/serial rating plate is located behind the oven
door on the top right-hand side of the oven frame.
• This range is manufactured with the neutral terminal
connected to the cabinet. Use a 3-wire, UL listed, 40- or
50-amp power supply cord (pigtail) (see the following Range
Rating chart). If local codes do not permit ground through the
neutral, use a 4-wire power supply cord rated at 250 volts,
40- or 50-amps and investigated for use with ranges.
Range Rating* Specified Rating of
Power Supply Cord Kit
and Circuit Protection
120/240 Volts 120/208 Volts Amps
8.8 - 16.5 KW 7.8 - 12.5 KW 40 or 50**
16.6 - 22.5 KW 12.6 - 18.5 KW 50
*The NEC calculated load is less than the total connected load
listed on the model/serial rating plate.
**If connecting to a 50-amp circuit, use a50-amp rated cord with
kit. For 50-amp rated cord kits, use kits that specify use with a
nominal 13/8"(34.9 mm) diameter connection opening.
A circuit breaker is recommended.
The range can be connected directly to the circuit breaker
box (or fused disconnect) through flexible or nonmetallic
sheathed, copper or aluminum cable. See the "Electrical
Connection - U.S.A. Only" section.
3-wire receptacle (10-50R)
If connecting to a 4-wire system:
This range is manufactured with the ground connected to the
neutral by a link. The ground must be revised so the green
ground wire of the 4-wire power supply cord is connected to the
cabinet. See "Electrical Connection - U.S.A. Only" section.
Grounding through the neutral conductor is prohibited for new
branch-circuit installations (1996 NEC); mobile homes; and
recreational vehicles, or an area where local codes prohibit
grounding through the neutral conductor.
When a 4-wire receptacle of NEMA Type 14-50R is used, a
matching UL listed, 4-wire, 250-volt, 40- or 50-amp, range power
supply cord (pigtail) must be used. This cord contains 4 copper
conductors with ring terminals or open-end spade terminals with
upturned ends, terminating in a NEMA Type 14-50P plug on the
supply end.
The fourth (grounding) conductor must be identified by a green or
green/yellow cover and the neutral conductor by a white cover.
Cord should be Type SRD or SRDT with a UL listed strain relief
and be at least 4 ft (1.22 m) long.
4-wire receptacle (14-50R)
The minimum conductor sized for the copper 4-wire power
cord are:
40-amp circuit
2 No.-8 conductors
1 No.-10 white neutral
1 No.-10 green grounding
• Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack in the line so that
the range can be moved if servicing is ever necessary.
• A UL listed conduit connector must be provided at each end
of the power supply cable (at the range and at the junction
box).
• Wire sizes and connections must conform with the rating of
the range.
• The tech sheet and wiring diagram are located on the back of
the range in a plastic bag.
6

Electrical Shock Hazard
Electrically ground range.
Failure to do so can result in death, fire, or
electrical shock.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path is adequate and wire gauge are in accordance
with local codes.
Be sure that the electrical connection and wire size are adequate
and in conformance with CSA Standard C22.1, Canadian
Electrical Code, Part 1 - latest edition, and all local codes and
ordinances.
A copy of the above code standards can be obtained from:
Canadian Standards Association
178 Rexdale Blvd.
Toronto, ON M9W 1R3 CANADA
• Check with a qualified electrical installer if you are not sure
the range is properly grounded.
Range Rating* Specified Rating of
Power Supply Cord Kit
and Circuit Protection
120/240 Volts 120/208 Volts Amps
8.8 - 16.5 KW 7.8- 12.5 KW 40 or 50"*
16.6 - 22.5 KW 12.6 - 18.5 KW 50
*The NEC calculated load is less than the total connected load
listed on the model/serial rating plate.
**If connecting to a 50-amp circuit, use a50-amp rated cord with
kit. For 50-amp rated cord kits, use kits that specify use with a
nominal 13/8"(34.9 mm) diameter connection opening.
A circuit breaker is recommended.
This range is equipped with a CSA International Certified
Power Cord intended to be plugged into a standard 14-50R
wall receptacle. Be sure the wall receptacle is within reach of
range's final location.
• Do not use an extension cord.
• The tech sheet and wiring diagram are located on the back of
the range in a plastic bag.

INSTALLATIONINSTRUCTIONS
'.... * Bsn,ge
Excessive Weight Hazard
Use two or more people to move and install range.
Failure to do so can result in back or other injury.
1. Remove shipping materials, tape and film from the range.
Keep cardboard bottom under range. Do not dispose of
anything until the installation is complete.
2. Remove oven racks and parts package from oven and
shipping materials.
3. To remove cardboard bottom, first take 4 cardboard corners
from the carton. Stack one cardboard corner on top of
another. Repeat with the other 2 corners. Place them
lengthwise on the floor behind the range to support the range
when it is laid on its back.
4. Using 2 or more people, firmly grasp the range and gently lay
it on its back on the cardboard corners.
5. Remove cardboard bottom.
The leveling legs can be adjusted while the range is on its back.
See the "Adjust Leveling Legs" section.
NOTE: To place range back up into a standing position, put a
sheet of cardboard or hardboard on the floor in front of range to
protect the flooring. Using 2 or more people, stand range back up
onto the cardboard or hardboard.
1,
2.
3,
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
Remove the anti-tip bracket from the inside of the oven.
Determine which mounting method to use: floor or wall.
If you have a stone or masonry floor, you can use the wall
mounting method. If you are installing the range in a mobile
home, you must secure the range to the floor.
This anti-tip bracket and screws can be used with wood or
metal studs.
Determine and mark centerline of the cutout space. The
mounting can be installed on either the left side or right side
of the cutout. Position mounting bracket against the wall in
the cutout so that the V-notch of the bracket is 121/2''
(31.8 cm) from centerline as shown.
/
Centerline i _[__
/
A. 12_/2'' (31.8 cm)
B.Bracket V-notch
8

4. Drill two %" (3 mm) holes that correspond to the bracket
holes of the determined mounting method. See the following
illustrations.
Floor Mounting
Rearposition
Wall Mounting
Front position Diagonal (2 options)
5. Using the Phillips screwdriver, mount anti-tip bracket to the
wall or floor with the two #10 x 1%" (4.1 cm) screws provided.
6. Move range close enough to opening to allow for final
electrical connections. Remove shipping base, cardboard or
hardboard from under range.
7. Move range into its final location, making sure rear leveling
leg slides into anti-tip bracket.
8. Move range forward onto shipping base, cardboard or
hardboard to continue installing the range using the following
installation instructions.
1. If range height adjustment is necessary, use a wrench or
pliers to loosen the 4 leveling legs.
This may be done with the range on its back or with the range
supported on 2 legs after the range has been placed back to
a standing position.
NOTE: To place range back up into a standing position, put a
sheet of cardboard or hardboard in front of range. Using 2 or
more people, stand range back up onto the cardboard or
hardboard.
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
2. Measure the distance from the top of the counter to the floor.
3. Measure the distance from the top of the cooktop to the
bottom of the leveling legs. This distance should be the
same. If it is not, adjust the leveling legs to the correct height.
The leveling legs can be loosened to add up to a maximum of
1" (2.5 cm). A minimum of 3/le"(5 mm) is needed to engage
the anti-tip bracket.
NOTE: If height adjustment is made when range is standing,
tilt the range back to adjust the front legs, then tilt forward to
adjust the rear legs.
4. When the range is at the correct height, check that there is
adequate clearance under the range for the anti-tip bracket.
Before sliding range into its final location, check that the anti-
tip bracket will slide under the range and onto the rear
leveling leg prior to anti-tip bracket installation.
NOTE: If a Trim Kit will be used, the top of the cooktop
should be higher than the counter. See the Installation
Instructions included with the Trim Kit for the correct height.

1. Place level on the oven bottom as indicated in one of the two
figures below depending on the size of the level. Check with
the level side to side and front to back.
3. Remove plastic tag holding three 10-32 hex nuts from the
middle post of the terminal block.
2. If range is not level, use a wrench or pliers to adjust leveling
legs up or down until the range is level.
NOTE: Range must be level for satisfactory baking
performance and best cleaning results using AquaLift _
Self-Clean Technology.
If your home has a 3- or 4-wire receptacle, continue with "Install
Using a Power Supply Cord." If your home has a 3- or 4-wire
direct connection, go to "Install Using Direct Wire."
Install Using a Power Supply Cord
Electrical Shock Hazard
Disconnect power before servicing.
Use a new 40 amp power supply cord.
Plug into agrounded outlet.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Power supply cord strain relief
1. Disconnect power.
2. Remove the lower access cover screws located on the back
of the range. Pull the bottom of the cover toward you and out
to remove cover from range.
B
4. Assemble a UL listed strain relief in the opening.
A. UL listed strain relief
5. Complete installation following instructions for your type of
electrical connection:
4-wire (recommended)
3-wire (if 4-wire is not available)
Electrical Connection Options
If your home has: And you will be Go to Section:
connecting to:
3-wire receptacle
(NEMA type 10-50R) A UL listed,
250-volt
minimum,
40- or 50-amp,
range power
supply cord
3-wire connection:
Power supply cord
4-wire receptacle
(NEMA type 14-50R) A UL listed,
250-volt
minimum,
40- or 50-amp,
range power
supply cord
4-wire connection:
Power supply cord
A. Three mounting tabs
S. Lower access cover
C. Screws (2)
10

3-wire connection: Power Supply Cord
Use this method only if local codes permit connecting chassis
ground conductor to neutral wire of power supply cord.
1. Feed the power supply cord through the strain relief on the
cord/conduit plate on bottom of range. Allow enough slack to
easily attach the wiring to the terminal block.
2=
A. Terminal block
B. Ground-link screw
C. UL fisted strain relief
D. Power supply cord wires -large opening
Use 3/8"nut driver to connect the neutral (white) wire to the
center terminal block post with one of the 10-32 hex nuts.
4-wire connection: Power Supply Cord
Use this method for:
• New branch-circuit installations (1996 NEC)
• Mobile homes
• Recreational vehicles
• In an area where local codes prohibit grounding through the
neutral
1. Part of metal ground strap must be cut out and removed.
i L.........
A. Metal ground strap
B. Discard
C. Ground-link screw
A
B
C
2. Use a Phillips screwdriver to remove the ground-link screw
from the back of the range. Save the ground-link screw and
the end of the ground link under the screw.
3. Feed the power supply cord through the strain relief on the
cord/conduit plate on bottom of range. Allow enough slack to
easily attach the wiring to the terminal block.
A....................__
AE
C
A. 10-32 hex nut
B. Line 2(red)
C. Ground-link screw
D. Neutral (white) wire
E.Line 1 (black)
3. Connect line 2 (red) and line 1 (black) wires to the outer
terminal block posts with 10-32 hex nuts.
4. Firmly tighten hex nuts.
NOTE: For power supply cord replacement, use only a power
cord rated at 250 volts minimum, 40- or 50-amps that is
marked for use with nominal 13/8"(3.5 cm) diameter
connection opening, with ring terminals and marked for use
with ranges.
5. Tighten strain relief screws.
IMPORTANT: Verify the tightness of the hex nuts.
6. Replace lower access cover.
4=
©
jD
A. Terminal block
B. Ground-link screw
C. UL fisted strain relief
D. Power supply cord wires
Use a Phillips screwdriver to connect the green ground wire
from the power supply cord to the range with the ground-link
screw and ground-link section. The ground wire must be
attached over the ground-link section.
11

5. Use 3/8"nut driver to connect the neutral (white) wire to the
center terminal block post with one of the 10-32 hex nuts.
F
D
A. 10-32 hex nut
B. Ground-link screw
C. Line 2 (red)
D. Green ground wire
E.Neutral (center) wire
F. Line 1 (black)
6. Connect line 2 (red) and line 1 (black) wires to the outer
terminal block posts with 10-32 hex nuts.
7. Firmly tighten hex nuts.
NOTE: For power supply cord replacement, use only a power
cord rated at 250 volts minimum, 40- or 50-amps that is
marked for use with nominal 13/8"(3.5 cm) diameter
connection opening, with ring terminals and marked for use
with ranges.
8. Tighten strain relief screws.
IMPORTANT: Verify the tightness of the hex nuts.
9. Replace lower access cover.
Install Using Direct Wire
Electrical Shock Hazard
Disconnect power before servicing.
Use 8 gauge copper or 6 gauge aluminum wire.
Electrically ground range.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Direct wire strain relief
1. Disconnect power.
2= Remove the lower access cover screws located on the back
of the range. Pull the bottom of the cover toward you and out
to remove cover from range.
A
B
3=
A. Three mounting tabs
g. Lower access cover
C. Screws (2)
Remove plastic tag holding three 10-32 hex nuts from the
middle post of the terminal block.
4. Assemble a UL listed conduit connector in the opening.
5=
jjj_ S
A. Removableretainingnut
B. Conduit
Tighten strain relief screw against the flexible conduit.
12

Direct Wire Installation: Copper or Aluminum Wire
This range may be connected directly to the fuse disconnect or
circuit breaker box. Depending on your electrical supply, make
the required 3-wire or 4-wire connection.
1. Strip outer covering back 3" (7.6 cm) to expose wires. Strip
the insulation back 3/8"(1.0 cm) from the end of each wire.
3/8"
(I.o cm),_,
_ ........... 3"- '
(7.6era)
2. Allow enough slack in the wire to easily attach the wiring
terminal block.
3. Complete installation following instructions for your type of
electrical connection:
4-wire (recommended)
3-wire (if 4-wire is not available)
Electrical Connection Options
If your home has: And you will be Go to Section:
connecting to:
3-wire direct A circuit breaker 3-wire connection:
box or fused Direct wire
3/8" disconnect
4-wire direct
3/8"
(1.0cm),
(12.7 cm)
A circuit breaker 4-wire connection:
box or fused Direct wire
disconnect
3-wire connection: Direct Wire
Use this method only if local codes permit connecting ground
conductor to neutral supply wire.
1. Pull the wires through the conduit on cord/conduit plate on
bottom of range. Allow enough slack to easily attach the
wiring to the terminal block.
oB
©
2,
©
F
A. Terminal block
B. Ground-link screw
C. Cord/conduit plate
D. Line 2 (red) wire
E. Bare (green) ground wire
F. Line 1 (black) wire
Attach terminal lugs to line 2 (red), bare (green) ground, and
line 1 (black) wires. Loosen (do not remove) the setscrew on
the front of the terminal lug and insert exposed wire end
through bottom of terminal lugs. Securely tighten setscrew to
torque as shown in the following Bare Wire Torque
Specifications chart.
A
C D
A. Terminal lug
B. Setscrew
C. Line 2 (red) wire
D. Bare (green) ground wire
E.Line 1 (black) wire
13

Bare Wire Torque Specifications
Attaching terminal lugs to the terminal block - 20 Ibs-in. (2.3 N-m)
Wire Awg Torque
8 gauge copper 25 Ibs-in. (2.8 N-m)
6 gauge aluminum 35 Ibs-in. (4.0 N-m)
3. Use 3/8"nut driver to connect the bare (green) ground wire to
the center terminal block post with one of the 10-32 hex nuts.
"L
A
B
A. 10-32 hex nut
B. Line 2(red)
C. Ground-link screw
F
E
CD
D. Bare (green) ground wire
E.Line 1 (black)
F. Terminal lug
4. Connect line 2 (red) and line 1 (black) wires to the outer
terminal block posts with 10-32 hex nuts.
5. Firmly tighten hex nuts.
IMPORTANT: Verify the tightness of the hex nuts.
6. Replace lower access cover.
4-wire Connection: Direct Wire
Use this method for:
• New branch-circuit installations (1996 NEC)
• Mobile homes
• Recreational vehicles
• In an area where local codes prohibit grounding through the
neutral
1. Part of metal ground strap must be cut out and removed.
i .............
A
B
C
A. Metal ground strap
B. Discard
C. Ground-link screw
2. Use a Phillips screwdriver to remove the ground-link screw
from the back of the range. Save the ground-link screw and
the end of the ground link under the screw.
3. Pull the wires through the strain relief on bottom of range.
Allow enough slack to easily attach wiring to the terminal
block.
.... L.......... B
©
......_ C
A. Terminal block
B. Ground-link screw
C. Cord/conduit plate
D. Bare (green) ground wire
E.Line 2 (red) wire
F. Neutral (white) wire
G. Line 1 (black) wire
14

4= Attach terminal lugs to line 1 (black), neutral (white), and line 2
(red) wires. Loosen (do not remove) the setscrew on the front
of the terminal lug and insert exposed wire end through
bottom of terminal lugs. Securely tighten setscrew to torque
as shown in the following Bare Wire Torque Specifications
chart.
C
A. Terminal lug
B. Setscrew
C. Line 2 (red) wire
D. Neutral (white) wire
E. Line 1 (black) wire
B csc t s ,snd
On Ranges Equipped with a Premium Storage Drawer:
1. Slide range into final location, making sure rear leveling leg
slides into anti-tip bracket.
2. Remove the premium storage drawer. See the "Remove/
Replace Drawer" section.
3. Use a flashlight to look underneath the bottom of the range.
4. Visually check that the rear range foot is inserted into the slot
of the anti-tip bracket.
On Ranges Equipped with a Warming Drawer or Baking
Drawer:
1. Slide range into final location, making sure rear leveling leg
slides into anti-tip bracket. Leave a 1" (2.5 cm) gap between
the back of the range and the back wall.
2. Place the outside of your foot against the bottom front of the
warming drawer or baking drawer to keep the range from
moving, and grasp the back of the range as shown.
Bare Wire Torque Specifications
Attaching terminal lugs to the terminal block - 20 Ibs-in. (2.3 N-m)
Wire Awg Torque
8 gauge copper 25 Ibs-in. (2.8 N-m)
6 gauge aluminum 35 Ibs-in. (4.0 N-m)
5. Use a hex or Phillips screwdriver to connect the bare (green)
ground wire to the range with the ground-link screw and
ground-link section. The ground wire must be attached over
the ground-link section and must not contact any other
terminal.
6. Use 3/8"nut driver to connect the neutral (white) wire to the
center terminal block post with one of the 10-32 hex nuts.
C
A. 10-32 hex nut
B. Line 2(red)
C. Bare (green) ground wire
D. Ground-link screw
F
DE
E.Neutral (white)wire
F. Line 1(black)
G.Terminallug
7. Connect line 2 (red) and line 1 (black) wires to the outer
terminal block posts with 10-32 hex nuts.
8. Firmly tighten hex nuts.
IMPORTANT: Verify the tightness of the hex nuts.
9. Replace lower access cover.
3=
4=
5=
6.
7.
8=
Slowly attempt to tilt the range forward.
If you encounter immediate resistance, the range foot is
engaged in the anti-tip bracket. Go to Step 8.
If the rear of the range lifts more than 1/2"(1.3 cm) off the floor
without resistance, stop tilting the range and lower it gently
back to the floor. The range foot is not engaged in the anti-tip
bracket.
IMPORTANT: If there is a snapping or popping sound when
lifting the range, the range may not be fully engaged in the
bracket. Check to see if there are obstructions keeping the
range from sliding to the wall or keeping the range foot from
sliding into the bracket. Verify that the bracket is held
securely in place by the mounting screws.
Slide the range forward, and verify that the anti-tip bracket is
securely attached to the floor or wall.
Slide range back so the rear range foot is inserted into the
slot of the anti-tip bracket.
Repeat steps 1 and 2 to ensure that the range foot is
engaged in the anti-tip bracket.
If the rear of the range lifts more than 1/2"(1.3 cm) off the floor
without resistance, the anti-tip bracket may not be installed
correctly. Do not operate the range without anti-tip bracket
installed and engaged. Please reference the "Warranty"
section of the User Guide to contact service.
Move the range into its final location. Check that the range is
level by placing a level on the oven bottom. See the "Level
Range" section.
IMPORTANT: If the range is moved to adjust the leveling
legs, verify that the anti-tip bracket is engaged by repeating
steps 1-8.
15

_,0t_ ,,_,,,,_J(jj
Remove all items from inside the baking drawer, warming drawer
or premium storage drawer, and allow the range to cool
completely before attempting to remove the drawer.
To Remove:
1. Open the drawer to its fully open position.
2. Using a fiat-blade screwdriver, gently loosen the warming
drawer or premium storage drawer from the glide alignment
notch and lift up the drawer alignment tab from the glide.
A
For normal range use, it is not suggested to remove the oven
door. However, if removal is necessary, make sure the oven is off
and cool. Then, follow these instructions. The oven door is heavy.
To Remove:
1. Open oven door all the way.
2. Pinch the hinge latch between two fingers and pull forward.
Repeat on other side of oven door.
3.
A. Flat-blade screwdriver
B. Drawer alignment tab
C. Drawer gfide notch
Repeat Step 2 on the other side. The drawer is no longer
attached to the drawer glides. Using both hands, pick up the
drawer to complete the removal.
To Replace:
1. Align the forward drawer notches with the notches in the
drawer glides on both sides. Place the rear alignment tabs
into the drawer glides on both sides.
3.
4.
A. Hinge latch
Close the oven door as far as it will shut.
Lift the oven door while holding both sides.
Continue to push the oven door closed and pull it away from
the oven door frame.
To Replace:
1. Insert both hanger arms into the door. Be sure that the hinge
notches are engaged in the oven door frame.
A. Drawer alignment tab
B. Drawer glide notch
2. Push the drawer in all the way.
3. Gently open and close the drawer to ensure it is seated
properly on the glides on both sides.
A. Hinge notch
2. Open the oven door.
The door should be able to open all the way.
3. Move the hinge levers back to the locked position. Check
that the door is free to open and close and is level while
closed. If it is not, repeat the removal and installation
procedures.
16

1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
2. Check that you have all of your tools.
3. Check that you have all of the range accessories, especially
oven racks. These accessories may be in the range
packaging.
4. Dispose of/recycle all packaging materials.
5. Check that the range is level. See the "Level Range" section.
6. Use a mild solution of liquid household cleaner and warm
water to remove waxy residue caused by shipping material.
Dry thoroughly with a soft cloth. For more information, see
the "Range Care" section of the User Guide.
Read the User Guide.7=
8.
9.
If range does not operate, check the following:
• Household fuse is intact and tight; or circuit breaker has not
tripped.
• Range is plugged into a grounded outlet.
• Electrical supply is connected.
IMPORTANT: If the range control displays an "F9" or "F9, E0"
error code, the electrical outlet in the home may be miswired.
Disconnect power and contact a qualified electrician to verify
the electrical supply.
10. When the range has been on for 5 minutes, check for heat. If
the range is cold, turn off the range and contact a qualified
electrician.
Plug power cord into a grounded outlet. Turn power on.
Turn on surface elements and oven. See the User Guide for
specific instructions on range operation.
NOTE: Odors and smoke are normal when the oven is used
If you need Assistance or Service:
Please reference the "Warranty" section of the User Guide to
contact service.
the first few times.
17

18

SECURITEDELACUISINIERE
Votre securite et celle des autres est tres importante.
Nous donnons de nombreux messages de s_curit_ importants dans ce manuel et sur votre appareil m_nager. Assurez-vous de
toujours lire tousles messages de s_curit_ et de vous y conformer.
Voici le symbole d'alerte de s_curit&
Ce symbole d'alerte de s_curit_ vous signale les dangers potentiels de d_c_s et de blessures graves &vous
et &d'autres.
Tousles messages de s_curit_ suivront le symbole d'alerte de s_curit_ et le mot "DANGER" ou
"AVERTISSEMENT". Ces mots signifient •
Risque possible de d_cbs ou de blessure grave si vous ne
suivez pas imm_diatement les instructions.
Risque possible de d_cbs ou de blessure grave si vous
ne suivez pas les instructions.
Tous les messages de s_curit_ vous diront quel est le danger potentiel et vous disent comment r_duire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
Risque de basculement
Un enfant ou une personne adulte peut faire basculer la cuisiniere, ce qui peut causer un
d_ces.
Fixer la bride antibasculement au plancher ou au mur, conform_ment aux instructions
d'installation.
Faire glisser de nouveau la cuisiniere de fa£on a ce que le pied arriere de la cuisiniere se
trouve dans la fente de la bride antibasculement.
R_engager la bride antibasculement si la cuisiniere a _t_ d_plac_e.
Ne pas faire fonctionner la cuisiniere si la bride antibasculement n'est pas install_e et engag_e.
Le non-respect de ces instructions peut causer un d_cbs ou des brl)lures graves aux enfants et
aux adultes.
... Bride
antibasculement
Pied de
la cuisiniere
Pour v_rifier que la bride antibasculement est bien install_e et engag_e :
•Faire glisser la cuisiniere vers ravant.
•V_rifier que la bride antibasculement est bien fix_e au plancher ou au mur.
•Faire de nouveau glisser la cuisiniere vers rarriere de sorte que le pied de la cuisiniere
se trouve sous la bride antibasculement.
•Voir les instructions d'installation pour plus de d_tails.
19

EXIGENCESD'INSTALLATION
Rassembler les outils et pi@ces n@cessaires avant d'entreprendre
I'installation. Lire et observer les instructions fournies avec
chacun des outils de la liste ci-dessous.
Outils n_cessaires
• Un serre-c&ble (homologation UL).
Consulter les codes Iocaux. Verifier I'alimentation electrique
existante. Voir la section "Specifications electriques"
correspondante.
II est recommande de faire realiser tousles raccordements
electriques par un electricien qualifie agre&
• M_tre-ruban • Ruban adhesif de masquage
• Tournevis a lame plate • Cle a cliquet de 1¼.(13 mm)
• Tournevis Phillips • Tourne-ecrou de 1¼.(13 mm)
• Niveau • Tourne-ecrou de 3/8"
• Perceuse manuelle ou (9,5 mm) et s/le" (8 mm)
electrique • Foret de %" (3 mm) (pour
• Cle ou pince planchers en bois)
• Cisaille de ferblantier ou
• Marqueur ou crayon coupe-ills de gros diam_tre
(pour couper la tresse de
mise & la terre le cas
ech6ant)
Pi_ces fournies
Verifier que toutes les pieces sont presentes.
• 3 ecrous hexagonaux de 10-32 (fixes au bornier)
• 3 cosses pour c&blage direct
• 2visn°10x13i8"(4,1 cm) (pour le montage de la bride
antibasculement)
• Bride antibasculement (& I'interieur de la cavite du four)
La bride antibasculement doit etre solidement fixee &la
cloison arriere ou au plancher. La profondeur du plancher
peut necessiter des vis plus Iongues pour I'ancrage de la
bride dans le sous-plancher. Des vis plus Iongues sont
disponibles aupr_s de votre quincaillerie locale.
• Pour lemodele :
IEL7300
WEC530HOD
WEE730HOD
YIEL7300
YWEE730HOD
JES1450CD
JES1450D
JIS1450CD
JIS1450D
KSEG700E
KSEB900E
KSIB900E
MES8880D
WEE760HOD
YKSEG700E
YKSEB900E
YKSIB900E
YM ES8880D
YWEE760HOD
Grilles du four 2 3
Pi_ces n_cessaires
En cas d'utilisation d'un cordon d'alimentation electrique :
• Cordon d'alimentation (homologation UL) con£su pour
I'utilisation avec une cuisiniere. Pour service 250 volts
minimum, 40 A ou 50 A, compatible avec une ouverture de
diametre nominal 13/8"(3,5 cm) pour le raccordement, et avec
cosses rondes ou en fourche a pointes relevees a I'extremite
de chaque conducteur.
Pi_ces facultatives
Pour acheter ces accessoires ou d'autres, se reporter & la section
"Accessoires" du guide d'utilisation pour les informations de
contact.
•Trousses de garnitures lat_rales :
Blanc : commander la reference W10677527
Noir : commander la reference W10675026
Acier inoxydable : commander la reference W10675028
•Panneaux anti-_claboussures :
Hauteur 6" (15,2 cm), blanc : commander la reference
W10655448
Hauteur 6" (15,2 cm), noir : commander la reference
W10655449
Hauteur 6" (15,2 cm), acier inoxydable : commander la
reference W10655450
Exge s,c®sd em©/csc®m® ;s
IMPORTANT : Observer les dispositions de tousles codes et
r@glements en vigueur.
• C'est a I'installateur qu'incombe la responsabilite de
respecter les distances de separation specifiees sur la plaque
signaletique. La plaque signaletique se trouve derriere la
porte du four, dans le coin superieur droit du chassis.
• La cuisiniere doit etre installee a un endroit pratique dans la
cuisine.
• Dans le cas d'une cuisiniere encastree, I'enceinte doit
recouvrir completement les c6tes et I'arriere de la cuisiniere.
• Afin de supprimer le risque de brQlures ou d'incendie lie au
fait de se pencher au-dessus des plaques de cuisson
chaudes, les placards de rangement au-dessus des plaques
doivent etre evites. Si des placards de rangement sont
prevus, le risque peut etre reduit par I'installation d'une hotte
de cuisiniere ou d'un ensemble hotte/micro-ondes depassant
horizontalement de 5" (12,7 cm) au moins par rapport au bas
des placards.
• Toutes les ouvertures dans lemur ou le plancher de
I'emplacement d'installation de la cuisiniere doivent etre
scellees.
• Respecter les dimensions indiquees pour les ouvertures
decouper dans les meubles. Ces dimensions constituent les
valeurs minimales des degagements.
• La bride antibasculement doit etre installee. Pour I'installation
de la bride antibasculement fournie avec la cuisiniere, voir la
section "Installation de la bride antibasculement".
• Une source d'electricite avec liaison & la terre est necessaire.
Voir la section "Specifications electriques" correspondante.
• Contacter un installateur de revetement de sol qualifie, qui
pourra determiner si le revetement de sol peut resister & une
temperature d'au moins 200°F (93°C).
• Dans le cas de I'installation de la cuisiniere sur une moquette,
placer sous la cuisiniere un tapis isolant ou une plaque de
contreplaque de 1¼,,(0,64 cm).
20