Jenn-Air JFC2089HT User guide

Jenn Air 3 Door Panel Installation Quick Guide
Model: JFC2089HT
Updated 09/14/06
Top Panels: Width   Height(ininches)
1/4”or3/8”backer*     1713/16*  421/16
*Recessedbackeroption:Thebackermaterialisexposedalongthehandlesideofbothupperdoors.The1713/16”width
dimensionprovidesboth1/4”and3/8”backerswitha3/16”recessesfromthebackeredgetothepaneledgealongthehandleside.
Seepg2.Theexposededgeofthebackermaterialcanbecoveredwithwoodveneer,melamineorpaintedtomatcheitherthe
panelorrefrigeratorcolor.Handlemountingscrewswillretainpanelstothehingesideofthepanelframe.Afulldimensionbacker
withoutanyrecesswouldmeasure1715/16”.Forafulldimensionbacker,readandunderstandtheinformationandnotesfor1/4”
veneeredpanels.
FramelessOverlay(panelcoversmetaltrim)  181/8   421/4
FramedInlay(paneldoesnotcovermetaltrim)  1713/16  415/8
FramedVeneer**     18**   421/16
**Note:anadditionalinstructionspecictoa1/4”veneeredbacker.Themetalframeisdesignedtotapanel1715/16”wide.
Cuttingan18”panelallowsfora1/4”spacebetweenupperpanelsandcoversthe1/16”edgeofthealuminumtrimatbothendsof
thehandlesideofthepanel.Detailedlingisneededatthetopandbottomofthehandlesideofbothupperdoorsforthepaneltot.
TESTFITBEFOREANDDURINGFILING.Carefullyleasmallnotchapproximate1/16”x7/32”atthebottomofthehandlesideofthe
paneltoallowthepanelbottomtotintothetopandbottomaluminumtrim.TESTFITBEFOREANDDURINGFILING.Carefullylea
similar1/16”x7/32”notchatthetoptoallowthetoptrimtotoverthetopofthepanel.
Bottom Panel:Width   Height (ininches)
1/4”or3/8”backermaterial    363/16  2313/16
FramelessOverlay(panelcoversmetaltrim)  361/2   24
FramedInlay(paneldoesnotcovermetaltrim)  353/4   233/8
FramedVeneer     363/16  2313/16
Nobackerinstructions:Millpanelorframematerialtoincludea1/4”x3/16”tongueonthetrimedge.Useappropriateinlayor
overlaydimensiontoconstructpanelswiththeproperoutsidedimensions.Seeillustrationsonpage4.
Note:Longerscrewsareneededtoattachthehandlemountingpostswhenoverlaypanelsareapplied.Foreaseandavailability,
considerusingKregpocketscrews:2-1/2”,#8Coarse,Washer-Head.Predrillpanelswitha5/32”pilothole.DONOTpredrillthe
refrigeratormetaldoor.DONOTovertighten.

3/8” Backer Edge Details:
Note: Lower backer panel has 5/16” x 1/8” rabbit cut into all four sides
0 1/8"
0 1/4"
0 1/8"
0 1/4"
BOTT OM PANEL BACKER 0 5/16" 0 5/16"
0 1/8"
0 1/4"
(1/4” minimum)
0 3/8"
0 1/8"
0 5/16"
0 1/4"
(1/4” minimum)
0 3/8"
RIGHT PANEL BACKER
0 5/16"
Metal of Door Metal of Door
LEFT PANEL BACKER
HandleEdge
(requiresnish)
HandleEdge
(requiresnish)
HingeEdgeHingeEdge
HingeEdge
LEFTTOP RIGHTTOP

Cross Section of Overlay and Inlay Panels:
0 7/32"
Metal of Door
Framed Inlay
0 5/16"
0 1/4"
0 1/8"
0 3/8"
0 5/32"
Metal of Door
Frameless Overlay
0 3/16"
0 3/16"
01/4"
3/8”and1/4”Backers
LeftPanelShown

Panel With No Backer: TopViewCrossSectional
LeftPanelOnly
0 1/4"
0 3/16"
0 1/2"
Inlay Dimension
0 1/8"
0 5/16"
0 3/16"
0 1/4"
Overlay Dimension
0 1/8" Metal of Door
Metal of Door
NoBackerOverlayInstructions:Millallmoldingmaterialtofulldimension.
CutOnlytheframeedgestoproduce1/4”x3/16”tongueontheframeedges.
NoBackerInlayInstructions:Millallmoldingmaterialtoincludea1/4”x3/16”
tongueontheframeedge.Useappropriateinlaydimensionstoconstructpanels
withtheproperoutsidedimension.