Jenn-Air JXT5836 User manual

ModeJ Number:
Manufadurel Number:
Size:
J×T5830 J×T5836
$26E30 S26E36
30" 36"
GUIDE
TABLE OF CONTENTS
Satet'_ Instructions .................................................... 1
Controls 8; Features ............................................... 2-3
Maintenance ......................................................... 4-6
Warranty .................................................................. 7
Form No. A/05/04 Part No. 8_ 10P263-60 (02004 Maytag Appliances Sales Co. Litho U.S,A.

MODELS: JXT5830 JXT5836
lostallation
Theinstallationin thismanuarisintendedforquarifiedinstallers,servicetechniciansor persons
withsimilarqualifiedbackground.DONOTattempttoinstarlthisapplianceyourserf,rniurycourd
resurtfrominstallingtheunitdueto rackofappropriateerectricalandtechnicalbackground.
Air erectricar wiring must be properly installed, insulated and grounded. Overly accumulated
greasein old duct work should becleaned out or duct work should be replaced if necessaryto
avoid the possibility of a grease fire. Checkall ioints on duct work to insure proper connection
andall ioints should be properly taped.
Operations
Readall instructions in this manual before operating the appliance. Save these instructions for
future reference.
Always leave safety grills and filters in place.Without these components, operating blowers
could catch on to hair,fingers and looseclothing.
NEVERdisposecigarette ashes, ignitable substances,or any foreign obiects into blowers.
NEVERleavecooking unattended.When frying, oil in the pan can easily overheat andcatch fire.
The risk of self combustion is higher when the oil has been used severaltimes.
Cleaning
The saturation of greasy residue in the blower and filters may cause increased flammability.
Keepunit clean and free of grease and residue build-up at all times to prevent possible fires.
Filters must be cleaned periodically and kept free from accumulation of cooking residue (see
cleaning instructions inside).Oldand worn filters must bereplaced immediately. Donot operate
blowers when filters are removed. Neverdisassemble parts toclean without properinstructions.
Disassemblyisrecommended to be performedby qualified personnelonly. Callourserviceceno
ter for removal instructions. 1-800-JENNAIR(1-800-536-6247)
The manufacturer declines all responsibility in the event of failure to observe the instrucz
tions given here for installation, maintenance and suitable use of the product. Themanufacz
turer further declines all responsibility for injury due to negligence and the warranty of the
unit automatically expires dueto improper maintenance.
* Please check for latest specification revisions before any custom work or cutouts.

CONTROLS & FEATURES
TOUCHCONTROLS& FEATURES
@ £1ower On/Off
O DispmaLaLaLay(Speedlevel Delay Off indicator, Filte/Cleal]/Chal'ge)
[ 1 m
[ O LightsOn/Off/Hold to Dim
Adjust 3Speed Levels _ 15 Min Belay Off
@ SlowerOn/Off
Bypressing(_, theblowerisswitchedOnandOff.Whenswitchedon,theNowerstartsuponspeedHover3.
Speed Selection
The3 speedReveRsareseRectedbypressing_) to decreaseand (_ to increasespeedlevel.Thedisplay
indicatesmevemsemected.
O Belay Off
This is usedfor programmedshut downof Nower and Hights15 minutesafterthe functionis activated.
Press _) once,a dot flashesin the HowerrighthandsideofdispHay_ indicatingthe function ison.
Thehoodwill compBeteHyshutdown in 15 minutes.
Lights On/Off/Dim
SwitchlightsOnandOffbypressingkey _) once. Todim mights,pressandherod(_) for 2 seconds.
Advance Display Functions
Filter CleanReminder(Metal):
After every30 hoursof use,the displaywill startflashingan_ remindingyouto cleanthe metalfimters
for residueandpossiNedogs.

CONTROLS & FEATURES
CONTROLS:FILTERCHANGEINDICATOR(CARBONFILTERS)
Filter Change Reminder (Carbon, if fitted):
When your hood is installed as a 'Purifying' (Ductless Recirculating) unit,it is fitted with a set of
CarbonFilters to purify exhaust and fumes from cooking, then re-circulate the air within the home=
These Carbon Filtersare required to be replaced after every120 hours of use=The Filter Change
Reminder function in the microprocessor needsto beswitched on=The micropro_ssor in the
controls when set, will elapse and count usage time and indicate bya flashing _- when carbon
filter replacement is needed=
Setting the Filter Change Reminder:
When Off, hold _) for approx. 5 seconds.
The display will change from _}
(exhaust mode)to _, (purifying mode/
carbon filters used)this indicates that the
elapse timer function is switched on and
CarbonFilters are used.
Filter Replace indicator:
When the display _ starts flashing, the
CarbonFilters require r' eplacement.
Re-setting Function:
Oncefilters are replaced, with hood off,
pressand hold (_, the display will appear;
hold for approximately 5 seconds until
on display disappears 0 .The Filter
ChangeReminderis now re-set and a new
120 hours elapsecycle is initiated.
hotd 5 sees. display from <=o>to <C>
hold 5 sees. display from <C> to < >
¢ 0

CLEANING
Surface Maintenance:
Creanperiodically with hot soapy water and dean cotton croth. Do not use corrosive or abrasive
detergent (e.g. Cometpowder scrub, EasyOffoven creaner),or steerwoof/scouring pads which will
scratch and damage surface.
For heavier soil useriquid degreaser such as 'Formura409' or 'Fantastic' brand creaner:
After cleaning, you may use non abrasive stainresssteer perish/cleaners such as 3M or
ZERto perishand buff out the stainressluster and grain.Nways scrub rightry,with
dean cotton cloth, and with the grain.
Metal Filters
The Metar Filtersfitted bythe factory are
intended to filter out residue and grease
from cooking. It neednot be replaced on a
regular basis but are required to be kept cle
Filters shouldbe cleaned after every30
hours of use.
Removeand clean byhand or in
dishwasher.Spray 'Formula 409' or
equivalentdegreasing detergent and leave
to soak if heavily soiled.
Dryfilters and re-install before using hood.
Replacing Metal Filters
Shouldfilters wearout due to age and
prolonged use,replace with following part
number:
Hood Model: Part No. Filters in pkg.
JXT5830 ZOF_M052 2
JXT5836 ZOF-M053 3
Alsoreplacedamagedfilterthat has
puncturedor brokenmesh,bentor brokenframe.
Metallic Filters Dimensions
8.15" x 9.75"
207 mm x 248 mm

DUCTLESSCONVERSION
Ductless conversion is intendedfor applications where an exhaust duct work is not possible to be
installed.When converted, the hood functions as a "purifying" hoodrather than an exhaust hood.
Fumesand exhaust from cooking is drawn and filtered by a set of optional Carbon Filters.The air
is then purified and re-circuhted back within the home.
We recommend to ALWAYSexhaust air outside of the home by employing existing or installing
new duct work, if possible.The hood is mosteffective and efficient asan Exhaustunit. Onlywhen
the exhaust option is not possible should you recourse to converting the hood into a "purifying"unit.
When convertedto be a "purifying" unit, a set of Carbon Filters is requiredon top of the standard
Metal Filterset. Orderaccording to Partnumbers below. Thestandard Metal Filtersare intended
to capture residue from cooking and the optional Carbon Filters help to purify fumes exhausted
from cooking for re-circulation.
CarbonFilters (Required)
1.PurchaseductlessCharcoalFiltersasfo[[o_
Hood Model: Part No. Filters in pkg.
JXT5830 JFLTRC5830 2
JXT5836 JFLTRC5836 3
2, Removemetal filters on hood,
3,Install attachment bracket into metal filter,
4, Clip carbonfilter onto bracket,
5, Re-install metal filters.
6, Carbon Filtersmust be replacedafter
every 120 hours of use (or approximately
every2 to 3 months basedon the average
of 1-2 firs, of daily cookingtime),
The microprocessorin the controls when
set, will count usagetime and indicate
when carbon filter replacement is required
Carbon Filter Dimensions:
9" x 6.4"
228 mm X 162 mm

LIGHTS
Replacing Lightgulhs
Make sureaHpower is turned off and
burbsare cool
Removeby turning burbcounter
crockwise.
rf bulbs are difficurt to removedue to pro-
tongeduse, firmly attach a grasssuction cup
(readily avaHabreat most righting stores)
approximately the diameter of the burband
turn counter clockwise. You may arsousea
rubber or latex groveto get the sameeffect.
Replacementbulbs areavailable at
specialty righting stores. Purchasetype
GUIO120V50W harogenburbs.
Orto order burbs,preasecall our service
center:1-800-JENNAIR (1-800-536-6247)

Warranb]:
Full One Year Warranty =Parts and Labor
For one (1) year from the original retail pur-
chase date, any part which faib in normal
home use will be repairedor replacedfree of
charge.
Limited Warranty =Parts Only
Second Year _ After the first year from the
original purchasedate, parts which fail in nor-
maLhome usewil! be repairedor replacedfree
of charge for the part itself, with the owner
payingall other costs, incBding labor,mileage
andtransportation, trip charge and diagnostic
charge is required.
Canadian Residents
Theabovewarranties only coveran appliance
installed in Canadathat has been certified or
listed by appropriate test agencies for complio
anceto a National Standard of Canadaunless
the appliance was brought into Canadadue to
transfer of residencefrom the United Statesto
Canada.
Tbespecific warrantiesexpressedaboveam the
ONLYwarrantiesprovidedby the manufacturer
Tbesewarrantiesgiveyouspecifie/ega/rights,and
you may alsahave other rights wlTid7varyfrom
statetostate,
What is Net Cevered By These Warranties:
1=Conditionsand damages resulting from any of the following:
a. Improper installation, delivery,or maintenance.
b.Any repair,modification, alteration, or adiustment not authorized
bythe manufacturer or an authorized servicer.
c. Misuse,abuse,accidents, or unreasonableuse.
d. Incorrect ebctric current, voltage, or supply.
e. Improper setting of any control.
2.Warranties are void if the original serial numbers have been removed,
altered, or cannot be readilydetermined.
3=Light bulbs.
4.Productspurchasedforcommercialor industrialuse.
5.Thecostofserviceor servicecallto:
a.Correctinstallationerrors.
b.Instructtheuserontheproperuseoftheproduct,
c.Transporttheapplianceto theservicer:
6. Consequentialor incidental damages sustained by any personas a
result of any breachof these warranties. Some states do not allow the
exclusionor limitation of consequential or incidental damages, sothe
aboveexclusion may not apply.
if Yeu Need Service
Callthe dealer from whom your appliance was purchased or call
Maytag ServicesaM,Jenn°Air CustomerAssistance at 1-800-JENNAIR
(1-800-536-6247) USAand CANADAto locate an authorized servicer.
Be sureto retain proof of purchase to verity warranty status. Referto
WARRANTYfor further information on owner's responsibilities for warranty
service.
If the dealer or service company cannot resolvethe problem, write to
Maytag ServicesaM,Attn:CAIR®Center,RO.Box2370, Cleveland,TN
37320-2370, or call I=800=JENNNR (1-800-536-6247) USAand CANADA.
U.S.customersusingTTYfordeaf,hearingimpairedor speech
impaired,call1-800-688-2080.
NOTE: When writing or calling about a service problem, please include the
following information:
a.Yourname, addressand telephone number;
b. Model number and serial number;
c. Nameand address of your dealer or servicer;
d.A clear description of the problem you are having;
e. Proofof purchase(sales receipt)
User's guides,service manuals and parts information are available from
Maytag ServicesaM,Jenn-Air CustomerAssistance.