Jenn-Air JXT9036CDP User manual

RANGE HOOD
ModeJ Number: ]X[9030CDP
Manufactu wetNumber: MK7030
Size: 30"
JX[9036CDP
MK7036
36"
JXT9048CDP
MK7048
48"
GUIDE
TABLE OF CONTENTS
Satet_ Instructions .................................................... 1
Mountin¢ Heights 2
Ducting .................................................................... 3
Specifications ........................................................... 4
Installation ............................................................ 5-7
MK7030
_o_ NJENNoAiR
MK7048
F:orm No. A/06/04 Part No. 8110P262-60 ,¢2004 Maytag Appliances Sales (o. litho U.S.A.

IVIODEL$:JXT9030 JXT9036 JXT9048
Installation
Theinstallationin thismanuarisintendedforquarifiedinstallers,servicetechniciansor persons
withsimilarqualifiedbackground.DONOTattempttoinstarlthisapplianceyourserf,rniurycourd
resurtfrominstallingtheunitdueto rackofappropriateerectricalandtechnicalbackground.
Air erectricar wiring must be properly installed, insulated and grounded. Overly accumulated
greasein old duct work should becleaned out or duct work should be replaced if necessary to
avoid the possibility of a grease fire. Checkall ioints on duct work to insure proper connection
andall ioints should be properly taped.
* Please check for latest specification revisions before any custom work or cutouts.

LiST OF MATERIALS
1-Hood
2-Bafflefilters (2°30", 3°36", 4-48")
2-Halogenlight bulbs (3°48")
1-Hardwarepacketcontaining:
4-2" drywall screws
4-1 1/2" drywall screws
4-1" drywall screws
4-1/2" washers
3-wire connectors
NODUOTINGISINCLUDED
H

MOUNTINGHEIGHTS
Minimum mounting height between range top
to hoodbottom shouM be no tessthan 24".
12 _'
\1_
Min24"-Max 32"
36"
Maximum mounting height shouM be no
higher than 32".
rt is important to instarl the hoodat the
proper mounting height. Hoodsmounted too
row courd result in heat damageand fire
hazard; while hoods mounted too high will be
hard to reach and will rooseperformance
and efficiency.
rf availabb, arso referto rangemanufacturer's
height clearance requirements and recom-
mended hood mounting height above range.
DUCTING
A minimum of 8" round duct must be used to
maintain maximum air flow efficiency.
Alwaysuserigidtypemetalductsonly,
Flexibleductscouldrestrictair flowbyupto 50%.
Also use calculation (on right)to compute total
available duct run when using elbows, transitions
and caps.
ALWAYS,when possible, reducethe number of
transitions and turns. If long duct run is required,
increase duct size from 8" to 9" or 10". If a reduc-
er is used,install a long reducer insteadof a pan-
cake reducer. Reduceduct size as far away from
opening as possible.
Ifturns or transitions are required:
Install asfar away from opening andas far
apart, between 2, as possible.
Duct Run Calculation:
Maximum run
8" 100FT
CalculatedLength:
each 90 Elbowused 15 FT
each 45 elbowused 9 FT
each 8"
transition used 1 FT
each 3/14 x 10" to 8"
transition used 5 FT
SideWallCapw/damper 30 FT
RoofCap 30 FT
e,g,- 1 roof cap, 2x90 elbows, 1 x 45 elbow used;
=30' + 30' + 9' =69' used, 31' available for stroiqht duct runs,

DUCTJNG
NEVERexhaust air or terminate duct work into spaces between walls, crawl spaces,ceiling, attics or
garages.AIrexhaust must beducted to the outside.
UseMetal ductwork only.
FastenaHconnections with sheet metal screws and tape aHjoints w/certified SHyerTapeor DuctTape.
SomeDuctingOptions:
\\
Sidewailcap ]
w/gravitydamper
I
:ydamper
RoofPitch w/
Flashing& Cap

SPECIFICATIONS
Position of electrical knockout
30" 13 3/4" from the right
1 3/4" from the front
36" 3 7/32" from the right
4 23/32" from the back
48" 4 3/8" from the right
4 23/32" from the back
o
4-5/8"
o
TOPVIEW
1/2"ElecK,0.

MOUNTINGTHERANGEHOOD
ELECTRICAL
All Electricalwork mustbyperformedbyqualifiedelectricianor personwith similartechnical
knowhowandbackground.
Forpersonalsafety,removehousefuseoropencircuitbreakerbeforebeginninginstallation+
Donotuseextensioncordor adapterplugwiththis appliance+
FollowNationalelectricalcodesor prevaifinglocalcodesandordinances.
ElectricalSupply:
Thisappliancerequiresa 120V60Hzelectricalsupply,connectedtoan individual,properlygrounded
branchcircuit,protectedbya 15or 20 amperecircuitbreakeror timedelayfuse:Wiringmustbe2
wirew/ground:PleasealsoreferElectricalDiagramlabeledonproduct:
Cable Lock:
A cable locking connector (not supplied) might also required by local codes. Checkwith local
requirements and codes, purchaseand install appropriate connector if necessary.
CaNeLock

MOUNTINGTHERANGEHOOD
Begin bydetermining hood mounting height on wall.
2. Leverand mount the wood paneronto the wall at the appropriate height and secure it to the
studs. This wood panershourd be 1/2" x 3" and the width will either be 29", 35" or 47"
depending on the width of the hood. Measurethe distance between the wall mounting brackets
and fasten them onto the wood panel.Referto the diagram for how the brackets attach to the
panel Make sure they wil! fine up with the brackets on the back of the hood.Lift the hood and
hang it onto the brackets.
3. Temporarily removethe baffrefilters from hood,and feverhoodbyadjusting the metal brackets
rocated inside of the hood.(Note:there is approximately lOcm total adjustability up and down).
These brackets are adjusted by ascrew that can beeasily turned with your fingers. There is one
on each side on the inside back wall of the hood.After ensuring that the hood is level,complete
ly tighten the screws to secure the hood to the wall.
4. After the hood is attached to the mounting brackets, you may further secure it by screwing two
screws into the wall from the inside of the hood.There are two screw holes near the bottomthat
you can useas a guide.
/
¢
.....

MOUNTINGTHERANGEHOOD
5. hstaHerectricaL
6. hstaHductworkandtapeaHioints.
7. Poweruphoodandcheckforteaksaroundductjoints,andif necessaryapprymoreducttape.
tape
8. hstaH optional duct coverand/or backsprash.Notethat the duct cover and backsprashare
sold separately.
9. Reinstallthe baffrefilters.