Jensen JAS-725 User manual

AMAZON ALEXA-ENABLED BLUETOOTH/WI-FI
UNDER CABINET SMART MUSIC SYSTEM
MODEL: JAS-725
USER MANUAL
PLEASE READ THIS USER MANUAL COMPLETELY BEFORE OPERATING THIS UNIT AND
RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

E1
IMPORTANT SAFETY INSTRUCTIONS
When used in the directed manner, this unit has been designed and manufactured to ensure
your personal safety. However, improper use can result in potential electrical shock or fire
hazards. Please read all safety and operating instructions carefully before installation and use,
and keep these instructions handy for future reference. Take special note of all warnings listed
in these instructions and on the unit.
1. Read these instructions – All the safety and operating instructions should be read
before the appliance is operated.
2. Keep these instructions – The safety and operating instructions should be kept for future
reference.
3. Heed all warnings – All warnings on the appliance and in the operating instructions
should be adhered to.
4. Follow all instructions – All operation and use instructions should be followed.
5. Do not use this apparatus near water – The appliance should not be used near water; for
example, near a bath tub, washbowl, kitchen sink, laundry tub, in a wet basement, or
near a swimming pool.
6. Clean only with dry cloth – The appliance should be cleaned only as recommended by
the manufacturer.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions. The appliance should be situated so that its location or position does not
interfere with its proper ventilation. For example, the appliance should not be situated on
a bed, sofa, rug, or similar surface that may block the ventilation openings; or placed in a
built-in installation, such as a bookcase or cabinet that may impede the flow of air through
the ventilation openings.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. AC adaptor is used as disconnect device and it should remain readily operable during
intended use. In order to disconnect the apparatus from the mains completely, the AC
adaptor should be disconnected form the mains socket outlet completely.
10. Only use attachments / accessories specified by the manufacturer.
11. Use only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
14. This appliance shall not be exposed to dripping or splashing water and that no object
filled with liquids such as vases shall be placed on the apparatus.
15. Power Sources – The appliance should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance. Do not overload
wall outlet.
16. Do not attempt to dismantle, open or repair this product yourself. If a fault occurs, seek
advice from your local qualified service technician or contact the distributor via the
telephone number at the back of this instruction manual.
17. Nameplate is located on the top of product.

E2
CAUTION
Follow the advice below for safe operations.
To reduce the risk of fire, do not place any heating or cooking appliance beneath this unit.
Stop operation immediately if any liquid or solid object should fall into the cabinet.
If the unit is not to be used for a long period of time, make sure that all power sources are
disconnected from the unit. Unplug the AC-DC adaptor from the wall outlet. Make it a
practice to remove the AC-DC adaptor by grasping the plug and not by pulling the cord.
ON PLACEMENT
Do not use the unit in places, which are extremely hot, cold, dusty or humid.
Install the JAS-725 as far as possible from a source of noise. (for example, refrigerator,
microwave oven, fluorescent lamp, etc.)
Do not restrict the airflow of the unit by placing it in a place with poor ventilation, by
covering it with a cloth or by placing it on a carpet.
Should any trouble occur, remove the power source and refer servicing to qualified personnel.
COMPLIANCE WITH FCC REGULATIONS
FCC ID : 2ANH7-393MET8025
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.

E3
DEAR JENSEN® CUSTOMER
Selecting fine audio equipment such as the unit you've just purchased is only the start of
your musical enjoyment. Now it's time to consider how you can maximize the fun and
excitement your equipment offers. This manufacturer and the Electronic Industries
Association's Consumer Electronics Group want you to get the most out of your equipment
by playing it at a safe level. One that lets the sound come through loud and clear without
annoying blaring or distortion and, most importantly, without affecting your sensitive
hearing.
Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes of
sound. So what sounds "normal" can actually be loud and harmful to your hearing. Guard
against this by setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
•Start your volume control at a low setting.
•Slowly increase the sound until you can hear it comfortably and clearly, and without
distortion.
Once you have established a comfortable sound level:
•Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future.
After all, we want you listening for a lifetime.
We Want You Listening For a Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often undetectable until it is too late, this manufacturer
and the Electronic Industries Association's Consumer Electronics Group recommend you
avoid prolonged exposure to excessive noise.
Customer's Record:
The serial number of this product is found on its top cover. You should note the serial
number of this unit in the space provided as a permanent record of your purchase to aid in
identification in the event of theft of loss.
Model Number: JAS-725 Serial Number: ____________________

E4
PREPARATION FOR USE
Installing the JAS-725 under a cabinet
1. Make the position of the 3 holes by using the supplied template. Use a drill to make the
holes.
2. When the cabinet door overhangs the shelf and obstructs the unit, you can adjust the
unit/shelf height.
3. Install the unit with the supplied mounting kit.
Unpack the unit carefully to remove all the accessories from the packing. Verify that the
following accessories are present before setting up the unit.
Main Unit X 1
AC adaptor X 1
User Manual X 1
Mounting kit X 1
LOCATION OF CONTROLS
MAIN UNIT
LIGHT
DC 5V
LINE IN
1
2
3
4
5
6
22
7
8
11 13
9
REAR VIEW
FRONT VIEW
14
18 1819 2021 21
12 15 17 11

E5
CONTROLS
1. ALEXA MIC OFF Indicator
2. POWER ON / OFF / SOURCE Button
3. PLAY/PAUSE; BLUETOOTH PAIR; ANSWER CALL / END CALL BUTTON
4. MIC ON/OFF/FACTORY DATA RESET BUTTON
5. TAP TO TALK BUTTON
6. CABINET MOUNTING POINT
7. VOLUME+(UP) and VOLUME- (DOWN) BUTTONS
8. WPS BUTTON (Wi-Fi Protected Setup)
9. LIGHT ON/OFF; DISPLAY DIMMER BUTTON
10. LINE-IN MODE INDICATOR
11. MICROPHONES FOR ALEXA
12. PM TIME INDICATOR
13. ALEXA MODE / CONNECTION INDICATOR
14. LIGHT
15. LED DISPLAY
16. Wi-Fi MODE INDICATOR
17. BLUETOOTH MODE INDICATOR
18. CORD WRAP POINT
19. LINE-IN JACK
20. DC-IN JACK
21. SPEAKER
22. MICROPHONE FOR BLUETOOTH HANDFREE
BUTTON FUNCTIONS
Power
Tap to power ON, press and hold to power OFF.
Source
Tap to change the speaker modes - Wi-Fi / Bluetooth / Line-In
Volume
Press to adjust the volume up or down. You can also ask
Alexa to set the volume level by saying, “Alexa, set volume
to...” and insert the volume level you wat the speaker set to.
Example: If you say “Alexa, set the volume to 5” Alexa will
increase or decrease the volume level to 50% of maximum
volume.

E6
Connect the JAS-725 to Wi-Fi Network link up again.
In Wi-Fi Mode, press and hold this button once to link up the
JAS-725 with your Wi-Fi network. Follow the instructions on
the Jensen Wi-Fi Audio App.
Play/Pause
Tap to play or pause audio playing from the JENSEN Wi-Fi
Audio app or from a Bluetooth connected device.
Bluetooth Pair
Press and hold to connect to a new Bluetooth device.
Answer / End Call
Tap the button to answer an incoming call.
Tap the button again to end the call.
Alexa Mic ON/OFF AND TAP TO TALK
Tap the Tap to Talk button to activate Amazon Alexa and say a
command. You can also just say, “Alexa..”, within range of the
speaker’s microphones. Tap the Mic On/Off button to mute the
microphones and disable Amazon Alexa.
In Wi-Fi mode, press and hold this button for 10 seconds until
display changed to 12:00 then release it, unit will reset Wi-Fi to
factory setting then restart for set up.
Light
Tap the button to turn on light ON / OFF
Dimmer
Press and hold the button to change display dimmer settings -
low and high.
ALEXA MODE INDICATION
Flashing White
Wi-Fi is disconnected
Light Off
Wi-Fi is Connected
Solid Turquoise Alexa is listening
Solid Blue
Alexa is thinking
Turquoise and Blue
changing
Alexa is talking
Solid Red The microphones are muted
Flashing Amber The JAS-725 is not logged into your Alexa account
(follow the voice instructions for connecting)
LIGHT

E7
GETTING STARTED
CONNECTING THE AC POWER
This unit operates using the included AC adaptor with 5V 1.5A (center-positive
) output, and is compatible with standard 120V~ 60Hz AC household power
Insert the the DC Plug of the AC Adaptor into the DC IN jack on the back of the unit. Plug the
AC Adaptor into a standard 120V~ 60Hz AC wall outlet.
CONNECTING THE JAS-725 TO A WI-FI NETWORK
IMPORTANT:
•The JAS-725 only operates on a single band (2.4 GHz) Wi-Fi network. If you are having
problems connecting the JAS-725 to your network, check your router settings and make
sure the 2.4 GHz signal is turned and you are accessing the correct band before
proceeding.
•Before you begin, make sure you have an Amazon account. You need an Amazon
account in order to use the Alexa voice control. Go to “www.Amazon.com” to register.
Downloading the Alexa App
Download the Amazon Alexa app to your device by scanning the appropriate QR code below
or by searching for the Amazon Alexa app in the Google Play™ Store, or Apple App Store®.
MAINS SOCKET
AC ADAPTOR
DC 5V
LINE IN
REAR VIEW
AC~120v 60Hz
The Amazon Alexa app connects your speaker to the Alexa service. It’s also where you see
an overview of your requests and manage your contacts, lists, news, music and settings.
Once downloaded, open the Alexa app and log into your Amazon account. If you do not
already have an Amazon account, choose “Create a new Amazon account” and enter the
requested info. Once logged in, the app will prompt you for setup. You can add these details
now by choosing “Get Started,” or skip these steps and complete the process later. You
cannot use Alexa if you are not logged into an Amazon account.

E8
Downloading the JENSEN Wi-Fi Audio App
Download the JENSEN Wi-Fi Audio App to your device by scanning the QR codes below or
search for the Jensen Wi-Fi app in the Google Play™ Store, or Apple App Store®.
Note: You may need to have a valid premium account to use some of the 3rd party streaming
services available on the App.
Connecting to a Wi-Fi Network
In order to use the Wi-Fi feature of the JAS-725, the unit and your mobile device must both be
connected to the same Wi-Fi network. The JENSEN Wi-Fi Audio app will guide you through
the process, just follow the on-screen instructions and have your network password ready.
After the initial connection, the speaker will remember the Wi-Fi network and automatically
connect to it when it is in Wi-Fi Mode. If the speaker should become disconnected or will not
connect normally, repeat the steps below.
Initial Wi-Fi Connection
Note: If you have a dual band wireless router, be sure to connect to the 2.4GHz band and not
the 5GHz band.
1. When you first power up the JAS-725, the ALEXA MODE / CONNECTION LED may flash
multiple colors while powering up, this is normal. Please wait for the MODE /
CONNECTION LED to turn white and begin flashing slowly. A short melody will play
indicating the JAS-725 is in Wi-Fi Standby Mode.
2. Open the JENSEN Wi-Fi Audio App on your device and press “Search”, then “Add Device
(Image A, B, below).
Android Apple
The JENSEN Wi-Fi Audio App lets you play music and audio from Amazon Music and other
online music services. It also controls the speaker’s other functions, such as Multi-room play,
Multi-channel play, etc.

E9
3. From the drop down menu, select the JAS-725 from the list and press “Next” (Image C,
below).
4. The app will direct you to your mobile device’s Wi-Fi Settings Menu to connect directly to
the JAS-725. Press “Settings” (Image D, below) to go to your mobile device’s Wi-Fi
settings menu, then select JAS-725_XXXX (Where XXXX is the last 4 digits of JAS-725
mac address) and return to the app when you are connected.
5. Once you have returned to the app, select your Wi-Fi network/router and enter your
password, then touch the “Continue” button. This will connect your mobile device and the
speaker to your Wi-Fi (Image E, below).
6. The app will display its progress as it configures the unit and your Wi-Fi network. When
this is completed, a voice will announce the successful connection and the
Mode/Connection LED will turn off. Touch the “Next” button to select the JAS-725 name
from the list or you can set a custom name for the unit. (Image F, below).
7. Touch the “Finish” button on your smartphone screen to proceed to your Amazon Alexa
account Set-up.
AB
CD

E10
Connecting to Your Amazon Account
1. When the JAS-725 Wi-Fi connection is completed, the app will prompt you to link the unit
with the Amazon Alexa app on your device (Image G, below). If you do not have the
Amazon Alexa app on your device, refer to the instructions in the “Downloading the
Alexa App” section of the manual.
NOTE: If you do not want to login to your Amazon account and link Alexa to the unit at
this time, press “Cancel”. You can complete it later by following the steps on the
following page.
2. Enter your Amazon account information to complete setup and begin using Amazon
Alexa with your unit (Image H, below).
3. Follow the instructions on your smartphone’s screen.
4. After finishing the Amazon account set-up, the app will prompt you to change your
smartphone’s Wi-Fi setting to your Wi-Fi network. Touch the “Wi-Fi Setting” button on
your smartphone’s screen and select the same Wi-Fi network that your JAS-725 is
connected to.
EF
GH

J
Pop Music
JAS-725_XXXX
E11
5. Return to JENSEN Wi-Fi Audio App, you will see the JAS-725 now appears on the
“DEVICE LIST” screen.
PLAYING SCREEN DEVICE LIST
6. To add more speakers touch the “+” icon in the top right corner of your smartphone
screen and repeat the above steps.
Amazon Alexa Manual Setup
1. From the Music Player Screen (Image I, below), swipe right to access the Main Menu.
2. Select Amazon Alexa from the list (Image J, below).
3. Sign into your Amazon account when prompted.
Clock Display
After setting-up the JAS-725 on your Wi-Fi network, and successfully logging into your
Amazon account, the internal clock will automatically synchronize with your local network time
and will show on the display.
Swipe right
for Playing
Screen
Swipe left
for Device
List
Pop Music
JAS-725_XXXX
I
Swipe right
for Main
Menu
Swipe left
for Playing
Screen

Notes:
1.) In order to have correct clock displaying, make sure the smartphone used when
E12
setting up the JAS-725 is set to automatically update the time and time zone using
your local network time.
2.) To reset the clock, press and hold the Mic On/Off button for 10 second to completely
reset the unit, follow steps mentioned in “Reset JAS-725 WiFi to Factory Default
Settings” section below to setup the unit again.
Reconnecting the JAS-725 to a Wi-Fi network
1. Turn on the unit and select Wi-Fi mode, press and hold the WPS button on the front panel
of JAS-725. You will hear the “Internet setup mode, follow the instructions in the app to
finish the setup” voice prompt.
2. Follow the steps in “Initial Wi-Fi Connection” section of the manual.
Resetting the JAS-725 Wi-Fi to Factory Default Settings
1. Turn on the unit and select Wi-Fi mode, press and hold the WPS button for 10 seconds
and release the button. You will hear the “Restore to factory setting” voice prompt.
2. Wait for the unit to restart or until you the hear voice prompt for ready to set-up.
3. Follow the steps in “Initial Wi-Fi Connection” section of the manual.
Note: Always setup the Wi-Fi connection when the JAS-725 is ON and in Wi-Fi mode.
Pressing the WPS button in any other operation mode or in Standby mode may cause
an error to occur.
USING AMAZON ALEXA VOICE CONTROL
When asking Alexa questions always say “Alexa” first or tap the “Tap to talk” button on the
front panel, Alexa Mode LED turns Turquoise, this indicate Alexa is listening.
Play music from Amazon Music, Tuneln and many more apps/ services using just your voice.
Example: Say “Alexa . Play music from TuneIn Radio.”
Answers questions, such as time and date, find out sports scores and schedules, read
Audible audio books, listen to news, traffic and weather reports, find info on local businesses,
check Wikipedia Example: Say “Alexa . What time is it? ”
Take notes, prepare shopping lists, shop at Amazon.
Note: To enable voice control, you will need an account to play music from Amazon Music
and some other services.
Thingsto Try with Alexa
Saying Command When Alexa Start
Now that you are connected, try interacting with Alexa. Start by saying “Alexa,” or tap the Tap
to talk button. When the ALEXA Mode LED turns to solid Turquoise, give Alexa a command or
ask a question. Here are some examples:
»“Alexa, tell me a joke.”
»“Alexa, what’s in the news?”
»“Alexa, what can you do?”

E13
You can mute Alexa and disable the microphones by pressing the MIC ON/OFF button. The
MIC indicator LED will change to red while the microphones are muted. In this mode, the
speaker’s audio will still work normally.
Music Player Screen
This is the default screen when you open the JENSEN app.
Main Menu Screen
1. Search
Search for songs, albums and artists.
2. Favorites
Open songs, artists, albums, or
stations that you have saved.
3. My Music
Open music that is stored on your
mobile device.
4. Internet Music Services
Available third-party music apps.
5. Add more Services
Press to add more third-party apps.
6. Alternate Play Modes
Select Bluetooth/LINE-IN Mode.
1
3
6
2
4
5
Pop Music
JAS-725_XXXX
Swipe left
for Device
List
Swipe right
Main Menu
7
3
5
8
4
6
1
for
21. Music Directory
2. The Speakers Name
3. Add to Favorites
4. Current Playlist
5. Repeat/Shuffle
6. Volume
7. Play/Pause Controls
8. Current Source Playing

E14
Device List Screen
GROUP AND UNGROUP THE SPEAKERS
Multi-room Play
Place speakers in any room and use the app to play music from the speaker of your choice.
You can play different songs from different speakers, set individual volume levels, or you can
link all of the speakers to play the same song.
Multi-mode
In the Device List, press and hold a device icon for two seconds, then drag towards another
device to link the speakers together.
Note:
Solo-mode
Press and hold the device icon, then drag downwards past the dotted line.
Multi-channel Play with Multiple Speakers
You can use two or more speakers in one room for a surround sound effect by setting the
Audio Channel selector to “LR” (stereo) for all of the speakers.
You can also use two speakers at once for stereo play by setting the Audio Channel selector
to “L” and “R” for the “left” and “right” speaker respectively.
1. Add Device/Refresh List
Add more speakers or refresh
the list of available devices.
2. Speaker Settings
Rename a speaker, set preset
stations, and find additional
information on a speaker.
3. Audio Channel
Press to set audio channels for
the speaker: L / R / LR
(left/right/stereo).
4. Play All
Play music on all connected
speakers.
1
3
2
4
1.) Synchronized playback only works in Wi-Fi mode.
2.) Only the Master speaker in the group will have the Alexa voice control.
3.) Pressing the “Tap to talk” button on any Slave speaker will give you the voice prompt
allowing you to ungroup the speaker if you wish. Follow the on screen instructions or
see the Solo-mode section below to ungroup speaker.

1. With the JAS-725 in power ON Mode, tap the SOURCE button to select Bluetooth mode.
The Bluetooth Indicator LED lights and flashing. The JAS-725 is now ready to pair
(link) with your Bluetooth device.
2. Turn on the Bluetooth feature of your cell phone. Enable the search or scan feature to
find the JAS-725.
Note: If you have more than one JAS-725 within range, make sure you are connecting to
the appropriate speaker.
3. Select "JAS-725" from the device list when it appears on your device screen. If required,
enter the pass code “0000” to pair (link) the JAS-725 with your cell phone.
4. After successfully pairing (linking) your cell phone with the JAS-725, the Bluetooth Mode
Indicator LED stops flashing and remains lit. You can now play music from your cell
phone or Bluetooth device wirelessly to the JAS-725.
Note: If you want to connect the JAS-725 to another cell phone after pairing successfully,
then you need to turn off the Bluetooth on the paired cell phone first if it is in range
before going through the above steps. Otherwise, the JAS-725 will automatically
reconnect to the previously linked cell phone or device. Then press and hold the
Bluetooth /PLAY/PAUSE button to put the JAS-725 into Bluetooth pairing
mode, the LED Indicator will be flashing Turquoise.
5. Press the VOLUME +/- button to adjust the volume level.
6. Press the PLAY/PAUSE button to pause or resume playback.
7. To turn off the JAS-725 Bluetooth, press and hold the button on main unit for 2
seconds to turn the unit to standby mode. Mode Indicator LED turns off. Don’t forget to
also turn off the Bluetooth feature on your cell phone or Bluetooth device.
E15
PLAYBACK MUSIC ON THE SPEAKERS
Internet Music Services
Select your local songs through MY MUSIC.
Access Web Radio through Tuneln.
Change Input through Bluetooth or Line In.
Search for online songs through Search.
Access your Favorite songs through Favorites.
Access Web services by touching the corresponding icons.
BLUETOOTH OPERATION
PAIRING (LINKING) A BLUETOOTH ENABLED CELL PHONE OR OTHER BLUETOOTH
ENABLED DEVICE to the JAS-725
The JENSEN Wi-Fi Audio App supports and can play songs from
Amazon Music and other online music services. Similar to the
setup process for Alexa, some of these third-party services will
prompt you to log in and link your account with the JENSEN
Wi-Fi Audio App so that it can access media you already have
saved with that service.

E16
Notes:
1.) Refer to manual of your cell phone or other Bluetooth enabled device for Bluetooth
operation, since it may vary from model to model.
2.) If your Bluetooth enabled device does not support A2DP, it will not play the music
through the speaker, even after it's paired (linked).
3.) If you are pairing (linking) your computer to the JAS-725 using Bluetooth, you may
need to set the JAS-725 as your computer’s default sound device.
Re-linking to a cell phone or Bluetooth device
If your cell phone or Bluetooth device is already paired with the JAS-725, but became
unlinked at some point, even with both Bluetooth devices turned on. You can re-link them by:
1. Press and hold the /PLAY/PAUSE button to re-link your cell phone. The Indicator
LED will turn on and flash while linking.
2. Select the JAS-725 from the devices list on your cell phone for linking. The Indicator
LED stops flashing and remains lit if the JAS-725 and your cell phone have been re-linked
successfully.
3. You can also re-link the JAS-725 by using Bluetooth operation of your cell phone. Please
refer to operation manual of your cell phone for more information.
ANSWER THE INCOMING CALL
When your unit playing mobile music by Bluetooth and receiving an incoming call on your
mobile phone, the music will be stop and ring sound from your mobile phone. Tap the
PLAY/PAUSE button to answer the call. Tap the button again to end the call, the music
will sound again (or press the PLAY button to play again).
LINE-IN OPERATION
This unit provides a LINE IN jack for connecting external audio devices like MP3 players, CD
players and listen to them through the speakers of this unit.
1. Use an audio cable (included) with one 3.5 mm stereo plug on each end of the cable.
2. To select auxiliary audio input, plug one end into the Aux IN jack on the back of main unit.
3. Plug the other end of the cable into the Line-out Jack or Headphone Jack of your external
audio device.
4. Turn on the external audio device and tap the button to turn on the main unit.
5. Tap the MODE button to select LINE IN mode, LINE IN indicator LED turns on.
6. The volume level can now be controlled through the main unit. Operate all other functions
on the auxiliary device as usual.

NOTE:
If you connect this unit to the Line-Out Jack of your external device then you only need to
adjust the volume control of this unit. If you connected the Headphone Jack of your
external device then you may need to adjust both the volume control of your external
device and the volume control of this unit to find the most desirable volume setting.
Press and hold the POWER button for 2 seconds to turning off the unit when you finish
listening. Don't forget to switch off the power of your external device as well.
E17
RESETTING THE JAS-725
In case of malfunction due to electrostatic discharge, the apparatus has to be reset by
disconnecting it from mains supply. Unplug the AC adaptor from main power, wait at least for
60 seconds before reconnect the AC adaptor power.
CARE AND MAINTENANCE
1. Do not subject the unit to excessive force, shock, dust or extreme temperature.
2. Do not tamper the internal components of the unit.
3. Clean your unit with a dry cloth. Solvent or detergent should never be used.
4. Avoid leaving your unit in direct sunlight or in hot, humid or dusty places.
5. Keep your unit away from heating appliances and sources of electrical noise such as
fluorescent lamps or motors.
CLEANING THE UNIT
To prevent fire or shock hazard, disconnect your unit from the AC power source when
cleaning.
The finish on the unit may be cleaned with a dust cloth and cared for as other furniture,
Use caution when cleaning and wiping the plastic parts.
If the cabinet becomes dusty wipe it with a soft dry dust cloth. Do not use any wax or polish
sprays on the cabinet.
If the front panel becomes dirty or smudged with fingerprints it may be cleaned with a soft
cloth slightly dampened with a mild soap and water solution. Never use abrasive cloths or
polishes, as these will damage the finish of your unit.
CAUTION: Never allow any water or other liquids to get inside the unit while cleaning.
Note: This unit is not magnetically shielded and may cause color distortion on the screen of
some TVs or video monitors. To avoid this, you may need to move the unit further away from
the TV or monitor if unnatural color shifts or image distortion occurs.
TO HEADPHONE INPUT
or
EXTERNAL DEVICE
DC 5V
LINE IN
REAR VIEW

E18
TROUBLESHOOTING GUIDE
Should you experience difficulties in the use of this player please refer to the following chart or
call 1-800-777-5331 for Product Service and Support.
Solution
Reconnect to the AC outlet.
Try the unit on another outlet.
Turn the Volume control to a higher output.
Turn on the speaker and select Wi-Fi
mode.
Select the correct Wi-fi network from your
available options, or try your other device
to ensure your Wi-Fi network is working
properly.
Uninstall then reinstall the App, turn the
speaker power Off, and then On again.
Restart the setup using the WPS button.
Use the same WiFi network for speaker &
your smartphone.
Set-up the speaker by following the set-up
steps in the manual.
Select the JAS-725 from your smartphone
screen.
Go through “Bluetooth set-up Operations”
process to link to the JAS-725.
Relocate the speaker within Bluetooth
operating range (33 ft.)
Use Jensen app to connect JAS-725 to
your Wi-Fi network.
Create or login to your Amazon Alexa
account.
Tap the MIC ON/OFF button to enable the
microphones.
Decrease the volume.
If the external device original sound source
is of poor quality, distortion and noise are
easily noticed with high-power speakers.
Try a different audio source such as a
music CD.
If you are using an external sound source
like older generation of iPod, try reducing
the output volume on the device itself. Also
try turning bass boost OFF or change the
EQ setting.
Turn the unit off for a period of time or
lower volume.
Possible Problem
The unit is disconnected from the
AC outlet.
The AC outlet has not power.
The volume control has been
turned all the way down.
Speaker is off or not in Wi-Fi
mode.
The Wi-Fi network password is
incorrect or the network is not
working.
The JENSEN Wi-Fi Audio App is
not installed properly
The JAS-725 is not on same Wi-Fi
network as your smartphone.
Speaker is not set-up properly.
You have not selected casting to
the JAS-725.
The JAS-725 is not connected via
Bluetooth with your cell phone.
Speaker placement out of
Bluetooth range.
The JAS-725 is not connected to
your WiFi network.
You have not logged into your
Amazon Alexa account.
The JAS-725 microphones are
muted
Volume level is set too high.
Sound source is distorted.
This is normal.
Symptom
The unit does not
respond (no power)
Unit is ON but there
is low or no volume
Cannot connect to
a Wi-Fi network
No Sound
Alexa voice control
not working.
Sound is distorted
Unit gets warm
after extended play
at high volume

E19
SPECIFICATION
Power requirement:
Main Unit AC-DC Adaptor DC 5V, 1.2A
90 DAY LIMITED WARRANTY AND SERVICE
VALID IN THE U.S.A. ONLY
At Spectra, environmental and social responsibility is a core
value of our business. We are dedicated to continuous
implementation of responsible initiatives with an aim to
conserve and maintain the environment through responsible
recycling.
Please visit us at http://www.spectraintl.com/green.htm for more information on Spectra’s green
initiatives or to find a recycler in your area.
The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
and any use of such marks by Spectra Merchandising Intl, Inc. is under license. Other
trademarks and trade names are those of their respective owners.
Amazon, Alexa, and all related logos and motion marks are trademarks of Amazon.com, Inc. or
its affiliates.
Amazon Terms & Polices
The JAS-725 is an Alexa- enabled device. Before using this speaker, please read all rules and
policies for Alexa, including the Amazon.com Privacy Notice at www.amazon.com/privacy and
the terms found in the Alexa App in Help > legal & Compliance. These terms, notices, and
policies are, collectively, the “Agreements” By using Alexa, you agree to be bound by the
Agreements.
SPECTRA MERCHANDISING INTERNATIONAL, INC. warrants this unit to be free from
defective materials or factory workmanship for a period of 90 days from the date of original
customer purchase and provided the product is utilized within the U.S.A. This warranty is not
assignable or transferable. Our obligation under this warranty is the repair or replacement of
the defective unit or any part thereof, except batteries, when it is returned to the SPECTRA
Service Department, accompanied by proof of the date of original consumer purchase, such as
a duplicate copy of a sales receipt.
You must pay all shipping charges required to ship the product to SPECTRA for warranty
service. If the product is repaired or replaced under warranty, the return charges will be at
SPECTRA’s expense. There are no other express warranties other than those stated herein.
This warranty is valid only in accordance with the conditions set forth below:
1. The warranty applies to the SPECTRA product only while:
a. It remains in the possession of the original purchaser and proof of purchase is
demonstrated.
b. It has not been subjected to accident, misuse, abuse, improper service, usage outside
the descriptions and warnings covered within the user manual or non-SPECTRA
approved modifications.
c. Claims are made within the warranty period.