Jet WiFi Messenger Alarm User manual

JET® WiFi Messenger
Alarm Quick Start
Before You Begin
Mount and wire your alarm according to installation instructions.
NOTE:
• Cellular WiFi hotspots are not recommended for use with
this WiFi alarm, as intermittent or unreliable notification
service can result.
• WPA2 Security must be enabled on the wireless router
for WiFi connections.
This quick start manual covers setup using a WPS
connection to your wireless network.
STEP 1: WiFi Network Setup (WPS)
The blue network status light will illuminate
steadily when the JET WiFi Messenger Alarm
is successfully connected to the wireless
network.
POWER WPS INTERNET
E1
1. Press the WPS button on your wireless
router (often the back side of router).
2. Press the WPS button on the JET WiFi
Messenger Alarm (the blue network status
light will flash continuously).

STEP 2: Verification
1. After the alarm is successfully connected to the wireless network, allow 2 minutes before
proceeding.
2. Using your internet connected device (i.e. Laptop, Desktop, etc.), open a new web browser
window or tab.
Note: you must be connected to the same router as your JET WiFi Messenger Alarm.
3. Type the following into the address field at the top of your web browser:
www.mywifialarm.com or scan QR code.
4. Follow the registration link.
5. After reading and accepting the terms of the JET WiFi Messenger Alarm, enter your alarm’s Unit
ID# located on the back of the battery compartment cover. (DO NOT ENTER THE COLONS).
Click Configure.
6. If the JET WiFi Messenger Alarm has not been
verified, the DEVICE REGISTRATION screen will
open and you will be required to enter an email
address to receive a verification link. Enter your
email address and press the Request Verification
Code button.
Note: All future alarm notifications will be sent to
this verification email address in addition
to the email addresses entered on the JET
WiFi Messenger Alarm’s setup page.
7. An email will be sent to the verification email
address entered with a link to the Notification Setup
page. Click this link to access the Notification Setup
page. This email must be received and opened by
the same device used for the steps above.
8. If the JET WiFi Messenger Alarm has already gone through the verification process, the web
browser will immediately be redirected to the Notification Setup page.
E2
NOTE: Before continuing, make sure device shows
aCONSTANT BLUE LIGHT (not flashing light)
Please enter the Unit ID# on the label of your alarm system
This is found on the back of the Batery Compartment lid
This will be similar to A1B5 C3D2 E7C2
Configure
WARNING!
USE ALKALINE BATTERY
ONLY, NON-ALKALINE
BATTERY MAY REDUCE
PRODUCT PERFORMANCE
UNIT ID#
A1B5:C3D2:E7C2

STEP 3: Alarm Notification Setup
1. On the JET WiFi Messenger Alarm
setup page, fill in the appropriate
data:
a. Device Name: Enter a unique
device name for each JET WiFi
Messenger Alarm being installed.
EXAMPLE: “123 Main St
Hometown OH 12345” Maximum
30 characters including spaces.
b. Email Addresses: Fill in the email
addresses which will be receiving
notifications from the JET WiFi
Messenger Alarm.
c. Enter the phone number of
the device (or devices) that will
receive the text message.
Note: A minimum of one email address or text message phone number must be entered to receive
alarm notifications.
2. Click Submit to save your notification data.
STEP 4: Setup Testing
1. Press and release the “TEST” button on the JET WiFi Messenger Alarm. The alarm horn will
sound and the alarm light will activate while the “TEST” button is being held.
2. Verify that an alarm notification is received via email or text.
Note: It may take several minutes for the message to appear in your email inbox or message folder,
depending upon email server traffic or other circumstances. If you have not received a notification
within 5 minutes, verify the email address and/or cellular phone information is entered correctly and
that any email filters are set to allow messages from mywifialarm@mywifialarm.com.
While using a WiFi connection, a signal strength rating will also be sent with the alarm and power
restored notifications.
5.0 - 10.0 Great!
3.0 - 4.9 Good. No signal loss is expected.
2.0 - 2.9 Marginal. You may experience occasional signal loss.
0.0 - 1.9 Weak. Move alarm closer to wireless router.
Submit
Network Name (SSID)
WPA2 Security Key
No Security
Device Name
Email Address 1
Email Address 2
Text Message Phone Number 1
Text Message Phone Number 2
Notification Setup
S
ubmi
t
IP Address: 10.4.150.148
MAC Address: A1:B5:C3:D2:E7:C2
Battery Status: None (Hit F5 to refresh)
At least one email address or one phone number must be provided to receive notification messages.
Example: 123-456-7890
Example: 123-456-7890
E3

Troubleshooting Guide
Network status light flashes:
•One Flash Every Five Seconds: No WiFi can be found. Verify wireless router is powered
and functioning. Verify alarm is within range of wireless router.
•Two Flashes Every Five Seconds: An IP address cannot be obtained. Cycle the power to
your wireless router. Enable DHCP in your router set up (see router manufacturer’s
user’s manual).
•Three Flashes Every Five Seconds: Email is unable to be sent. Verify the internet
connection is functioning. Verify the email address is valid.
Alarm webpage is not found:
• Alarm is not connected to a wireless network. Connect to the wireless network according to
the setup instructions.
• Your internet connected device (laptop, desktop, tablet, smartphone, etc.) is not connected
to the same wireless network as the alarm. Connect your device to the same wireless
network as the alarm.
• The correct Unit ID# was not entered into the browser: www.mywifialarm.com. Follow the
registration link. Re-enter the correct Unit ID# for your alarm.
Notification emails or text messages are not received:
• Email address or cellular information was not set up correctly. Verify email addresses are
valid and/or cell numbers are entered correctly.
• Internet access is not functioning. Repair the internet connection.
• Notification email has been blocked. Unblock or allow emails from
[email protected] in your email account.
• The JET WiFi Messenger Alarm terms and conditions have not been accepted and/or a
veri fication email has not been sent. Follow steps in the “Verification”section.
Congratulations!
Your JET WiFi Messenger Alarm
is now configured and ready to be used.
(Remember to test your alarm on a regular basis to ensure proper operation)
E4
01/25/2019
QA-SAL-357
JET® is a registered trademark of Jet, Inc.