Jetcom CCTV SS-HDR-8704 User manual

In order to ensure your rights and interests, please read this manual carefully before you install
and use the DVR.
Use the appropriate adapter for the DVR.
To protect the main chip from thunder striking, please make sure the ground wire is correctly
connected before using the DVR.
Do not expose the DVR to rain or use it under high humidity circumstance.
This DVR cannot be installed at the places with much dust, and avoid potential mechanical
vibration or impact.
Install this DVR under good air circulation conditions. Do not place it near the heater or under
direct sunlight.
Please choose high quality hard disk (HDD), which could meet the working demand of the DVR.
For its quality, please purchase hard disk from regular merchants, and do not use t he Western
Digital hard disk.
CAUTIONS
Network Digital Video Recorder Operation Manual ( V1.0 )

Before connecting to other facilities, please disconnect the power supply and pull the power line
plug out from the power socket.
In case of any solid or liquid coming into the case, please disconnect the power supply
immediately, and the DVR can be restarted only after being checked by qualifi ed se rviceme n.
If the DVR is not in use for a long period of time, please disconnect the power supply and pull
the power line plug out from the power socket.
This is a precise instrument. No internal part can be repaired by the users. If fault oc curs, it is
necessary to ask qualified servicemen to repair it or contact the dealer.
Network Digital Video Recorder Operation Manual ( V1.0 )

6
6
8
13
19
Table of contents
Chapter II Operation instructions
Chapter I Product Introduction
1.1 Summary
1.2 Functions and features
2.1 Description of front panel
2.2 Description of rear panel
2.3 Connection figure of rear panel
2.4 Description of alarm port in the rear panel
2.5 Remote control operation
2.6 Mouse operation
Chapter III Menu Setup
3.1 Summary of menu operation
Network Digital Video Recorder Operation Manual ( V1.0 )
14
19
18
15
6
8
11
3

3.2 System setup
3.3 Camera setup
3.4 Record setup
3.5 Schedule setup
3.6 Motion alarm
3.7 PTZ setup
3.8 Network setup
3.9 Alarm setup
3.10 Disk management
3.11 User setup
23
22
25
26
27
28
29
30
31
31
31
24
34
35
Chapter IV Basic Operations
4.1 Turn on DVR
4.2 Live screen
4.3 Software update
4.4 PTZ control
Network Digital Video Recorder Operation Manual ( V1.0 )
4
20

Appendix 1 Technical parameters
Appendix 2 Trouble shooting
38
38
39
39
42
43
44
44
45
46
48
42
4.5 System information
4.6 Log list
4.7 Recording preparation
4.8 Recording operation
4.9 Search, playback and backup
4.10 Audio setup
4.11 SEQ
4.12 Spot output
4.13 User login
4.14 PC Client software instruction
4.15 Power off
Network Digital Video Recorder Operation Manual ( V1.0 )
5
37

1.1 Summary
Chapter I Product Introduction
1.2 Functions and features
Network Digital Video Recorder Operation Manual ( V1.0 )
6
Support PAL & NTSC video signal input.
Support OSD languages of multiple countries.
Support external alarm, motion detection and time recording.
Support audio recording, audio playing and live mode listening.
This equipment is a standalone digital hard disk video recorder specially designed for security. It adopts the
embedded processor and embedded operating system and integrates with latest technologies in IT field, such as video
frequency/audio frequency compression/decompression, large capacity hard disk storage, TCP/IP network remote
control etc., investing the system with high intellectualization and stability.
This equipment supports various networks including Ethernet and Internet to realize remote audio/video
synchronization. With easy operation, it can be applied to the security for banks, telecom, schools, hospitals,
supermarkets,residential quarters, factories, companies, warehouses, restaurants, hotels, parks, museums, water
conservancy facilities, entertainment places and other fields.

If the electricity suddenly off while recording, it will record automatically when power on.
Support CMS
Support DDNS
Support network preview, playback, setup, remote recording, PTZ control and camera name setup.
Support IE browsing and Network remote Client.
Support Internet backup ,USB backup.
Support mouse operation with high sensitivity
Support 2000G hard disk and DVD Writer.
Support HDMI VGA output.
Support Remote Control and Control Keyboards operation.
Convenient & precise video searching
Control PTZ and speed dome through RS485
Specially designed dedicated file system for video to increase more than 10 times of service life of hard disk
Fully independent from PC platform and free from computer breakdown due to improper operations, complicated
management & operations as well as virus infection, and with high stability
Operating system: Linux
Compressed chip: SOC
Network Digital Video Recorder Operation Manual ( V1.0 )
7

Chapter II Operation Instructions
2.1 Description of front panel
DescriptionNameNo.
Network Digital Video Recorder Operation Manual ( V1.0 )
8
1Number keys
a) input numbers.
b) keystroke 1~9 : select channels.
Press it once to input number 0. Press it twice to input number 10.c) [0/10+]:
d) input password.
19
0/10
Icon
1 2
3
7
6
4 4
5

2
3
LED Indicator
light
IR Remote signal receiver LED indicator light. It is on in remote control usable
mode.
Lock LED indicator light. It is on in locking mode.
Hard drive LED indicator light. It will flash when the HDD is being used.
It is red in running mode, it is green in standby mode. It is off in pow er off
mode.
Start recording. In PTZ mode, it is used as [Z+] key in the remote control.
Press it to pop up search menu, select a video file to play. Press it to pause in
the process of playback, press it again to play again. In PTZ mode, it is used
as [Z-] key in the remote control.
In playback mode, press it to stop playing and return to search menu; in video
recording mode, press it to stop recording; in PTZ mode, press itto view preset
image.
Press it in live/record/playback mode to change the screen into four-split screen.
Press it in live/record/playback mode to change the screen into night-split screen.
To modify the parameters downward in PTZ control mode.
Press it to enter search menu. In PTZ mode, press it to set preset image.
Press it to enter search menu
LOCK
HDD
POWER
COPY
Network Digital Video Recorder Operation Manual ( V1.0 )
Record
Playback/
Pause
Stop
Search
Backup
Quad key
Nine-split key
Sixteen-split key
9

PTZ
INFO
ESC
SEQ
AUDIO
MENU
SPOT
Press it to enter PTZ mode, press again to exit.
press it once to pop up a tool menu on the top right of the screen, press it again
to enter into system information menu, press it three times to pop up log list menu.
Press it to exit from the inferior menu and return to the super ior menu. In
record/playback mode, press it to turn back to live mode.
In live/record/ mode, press this key to switch full screen images by sequence.
Press it to pop up audio setup menu.
Press it to pop up the main menu.
Press it to pop up SPOT setup menu.
Lock the machine.
3
4
5
LOCK
a) are direction keys. In menu mode, select the listed
options upward/downward/leftward/rightward; in PTZ control mode, control
the dome to rotate upward/downward/leftward/rightward.
confirm the selection and operation.
b)
c) rewind and forward in playback mode. Change the parameters
value in menu mode.
In live mode, is four-split key, nine-split key and sixteen-split key.
Direction /
split/
confirm keys
Network Digital Video Recorder Operation Manual ( V1.0 )
Information
Exit
Menu
PTZ
Sequence
Audio
SPOT output
Lock
10

Network Digital Video Recorder Operation Manual ( V1.0 )
USB port Connected to USB pendrive or mouse and used for system software upgrade
or video file backup; It supports hot plug.
IR Receiver Receive signal from remote control. (Do not cover).
6
7
2.2 Description of rear panel
11
11
Rear panel B of 4 channel:
Rear panel B of 8 channel:
11

Video input
Video output
Standard BNC port, connected with the camera and speed dome.
Connected with the video input of the monitor.
SPOT Connected with spot output device to view the live image independently.
RS485 devide into A and B. it can control PTZ via the mouse, remote control
and network Client . Connected with alarm input and output.
It is connected with External Remote Control Receiver connector.
485
ALARM
IR
USB
NET
VGA
Audio output
Audio input
Connected to USB pendrive or mouse and used for system software upgrade
or video file backup; It supports hot plug.
Port
No. Description
Power
Standard RJ-45 network port, connected to network cable and used for
remote browse or control.
VGA video signal output port, connected with the VGA port of a computer
monitor.
Connected with earphone or cable speaker.
Connected with audio input device, e.g. microphone.
DC12V/5A.
Power input port
Turn on/off the DVR.
Network Digital Video Recorder Operation Manual ( V1.0 )
12

Network Digital Video Recorder Operation Manual ( V1.0 )
Take8 channel DVR as exampleto show how to connect.
camera1 camera8
video output
SPOT output
Video input
2.3 Connection figure of rear panel
alarm port
Remote IR Receiver Port
VGA output
network port
power Input
power switch
audio output
audio input port
PTZ
USB port
13

2.4 Description of alarm port in the rear panel
Network Digital Video Recorder Operation Manual ( V1.0 )
Connection figure of alarm input and output.
Description:
(1) "1-8" is alarm input. "NC/NO/COM": Alarm relay output. NC is n ormal clos e, NO is normal open, COM is the
public terminal.
(2) " " It is ground wire.
Prompt: To make the machine work well, please follow the above figures to connect. Please power off each
device before connection.
4 channel 8 channel
alarm input
alarm output
-
+
12V
PTZ
alarm input
alarm output
-
+
12V
PTZ
14

3. Trouble shooting
2.5 Remote control operation
1. Installing the remote control
2. Using the remote control
Network Digital Video Recorder Operation Manual ( V1.0 )
Open the battery cover, install two batteries (Type No.7), make sure positive and negative
poles are right, then close the battery cover.
Before using it, please confirm that batteries have been installed correctly.When using it,
please aim IR TX (transmitter) of the remote control at IR reception of the DVR.Then the IR
light in the front panel is on and the icon on the top-right of the m onitor screen turns to blue
" " The DVR can be controlled by the remote control.
Note: If you don't want to use the remote control, you could set in the system setup menu.
Set the item REMOTE ID as OFF. Then the IR Receiver light in the front panel will be
off and the operation of the remote control is invalid.
If the DVR can not be controlled by the remote control, please check the following aspects:
1 Check the positive and negative poles of the batteries.
2 Check the electric quantity of the batteries.
3 Check that whether Remote Sensor are blocked or not.
4 Whether Fluorescent lamps are being used or not nearby.
15

Function description:
Network Digital Video Recorder Operation Manual ( V1.0 )
2Audio
Number
Record
Play&pause
Stop
Info
3
4
5
Audio setup menu will pop up.
Lock the machine or change the user.
Control the machine by remote control.
Lock
Remote ID
1Power
Press key to enter record mode.
In live or record mode, press it to pop up search menu, select a video file to play.
Press it to play, press it again to pause.
Press it to stop playing.
press it once to pop up a tool menu on the top right of the screen, press it again
to enter into system information menu, press it three times to pop up log list menu.
19
Select channels or set up password.Input nunber 0. Press it twice to select channel
10. Combined number keys 1-9 to select the channels from channel 11 to 16.
In normal running mode, press " " key to pop up a menu to prompt whether to
turn off. The DVR will be turned off . Press the key about 3 seconds, the DVR will
start.
16

Network Digital Video Recorder Operation Manual ( V1.0 )
5
6
7
Forward
Rewind
ESC
MENU
Direction
Confirm
Exit
Menu
Quad
Eight-split
Sixteen-split
In playback mode, p ress / key to play images forward or backward at
2X speed. Press it twice to play at 4X speed. Press it third time to play at 8X speed,
four times for 16X, five times for32X, six times for 64X,
To move the cursor up/ down/ left/ right to select items or modify data. And control
PTZ to move.
Confirm the operation.
Cancel the operation and exit.
Enter into the main menu.
The monitor display quad-screen. Press it to set preview point in PTZ mode.
The monitor display eight-split-screen. Press it to preview in PTZ mode.
The monitor display sixteen-split-screen. Press it to decrease the data in PTZ mode.
Sequence
Spot output
PTZ
AUTO
Zoom in/out
Focus
SEQ
SPOT
PTZ
AUTO
Z+/Z-
F+/F-
In live preview mode, press this key to automatically switching full screen images.
Press it to increase the data in PTZ mode.
In PTZ control mode, press it to move the cursor among the digital in the screen.
Enter into PTZ mode. Press it again or press "ESC" key to exit.
In PTZ control mode, this key is used to rotate PTZ automatically.
In PTZ control mode, this key is used to zoom in/out.
In PTZ control mode, "F+/F-" key is used to prolong/ shorten the focus.
17

2.6 Mouse operation
Network Digital Video Recorder Operation Manual ( V1.0 )
7
8
CRUISE
FOPEN
FCLOSE
In PTZ control mode, "I+/I-" key is used to enlarge/ reduce the iris (aperture).
I+/I-
Standby
IRIS
USB mouse can be used. Hot swap for mouse is supported. Move the mouse cursor onto the mouse icon to see
the name. Please insert the usb mouse into the usb port of the rear panel.
1 Select or cancel " " in the item.
2 Input password in user log in interface.
3 Click the close icon on the top-right of the screen to exit from the main menu.
4 In split-screen mode, click one of the channels to make it full screen. Click it again
to return to split-screen. Switch single channel screens.
5 In menu mode, it could modify the data.
Left-click the mouse
1 In live or playback mode, it could swich the single channel image.
2 In menu mode, it could modify the data. 3 To pop up the mouse tool icons.
Right-click the mouse
18

Chapter III Menu Setup
3.1 Summary of menu operation
Network Digital Video Recorder Operation Manual ( V1.0 )
SAVESAVE EXITEXIT
In live preview mode, select MENU key i n the remote contr ol / the front panel or click " " ico n in mouse
menu to enter the main menu. Press ESC key or click the CLOSE icon that on the top right of the menu to exit from
the main menu. Main menu is as follows.
Please press / in the front panel / in the remote control or left/right-click with the mouse to
change the parameter value in the sub-menu. Press / key in the remote control or in the front panel to move
the cursor or move by the mouse. Click" "to save the value and click " " to exit from the menu.
Move the mouse
1 Move the cursor.
2 Move the cursor to the bottom of the screen to pop up the mouse tool bar. Move
the cursor onto the icon to show the name.
1 To select shield area in "Camera setup".
2 To select motion detection area in "Motion alarm".
Drag the mouse
To change the value or digital in menu mode.
Mouse wheels
19