JetDryer Business2 User manual

Business2Hand Dryer
INSTRUCTION MANUAL
High Speed
JetDryer Business2 instructions_Oct15_Layout 1 18/07/2016 1:30 pm Page 1

Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
Item Category Performance Data
Operating Voltage
Warm Air Speed Output 246mph
110-120Vac, 60Hz, 700 watts (heater o) 1400 watts (heater on)
Display LED countdown
Motor Type 35,000 rpm, Brushless DC
Motor Thermal Protection
Heater Element 700 Watts
Auto Resetting Thermostat turns unit o at 271.4˚F (133˚C)
Heater Thermal Protection Auto resetting
Antibacterial lter
Filter
Air Freshener/Sanitizer Organic ocean breeze fragrance
Drying Time 10 - 15 seconds
Circuit Operation Infared Automatic, self adjusting
30 seconds auto shut o
Timing Protection
Decibel Rating 78dba @ 3 feet
Drip Proof IP22
Isolation CLASS I
Net Weight 18.4lbs
Shipping Weight 22lbs
Unit Size 113/4"W x 263/4"H x 93/4"D
CE, WEEE, Greenspec, ETL
Item Code Cover Type/Finish
JDBUSI2-WUS ABS White
JDBUSI2-SUS ABS Metallic Silver
263/4"
11
3/4
"
93/4"
General Safe
This product is
qualied servic
conductor for w
Failure to prop
electrical shock
Disconnect po
installing or se
NOT FOR HOUS
All units must b
ground wire m
back plate.
Installation
Installation mu
electrician
Installation must
current edition o
having jurisdicti
2. Place template
(see mounting h
locations of 4 mo
knockout (KO) lo
NOTE: For two o
closer than 24 in
3. Remove and r
4. Connect supp
indicated and co
ground screw.
2
Business2
JetDryer Business2 instructions_Oct15_Layout 1 18/07/2016 1:30 pm Page 2

)
Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
General Safety Information
This product is intended for installation by a
qualied service person. Use AWAG No. 16 solid
conductor for wiring.
Failure to properly ground unit could result in
electrical shock and/or death.
Disconnect power at the service breaker before
installing or servicing.
NOT FOR HOUSEHOLD USE - MAY CAUSE BURNS
All units must be supplied with a 3-wire service. The
ground wire must be connected with the dryers
back plate.
WARNING NOTE: Do not install dryer over wash basin.
Type Y attachment
If the power supply cord is damaged, it must be
replaced by the manufacturer or its service agent or a
similar qualied person in order to avoid a hazard.
Means for disconnection must be incorporated in the
xed wiring in accordance with the wiring rules.
Installation
Installation must be carried out only by a qualied
electrician
Installation must be carried out in accordance with the
current edition of the local wiring regulations code
having jurisdiction. Installation should be performed
2. Place template against wall at desired height
(see mounting height recommendations) and mark
locations of 4 mounting holes and wire service entry at
knockout (KO) location.
NOTE: For two or more dryers, dryers should be no
closer than 24 inches (610 mm) on centre.
3. Remove and retain 2 cover screws.
4. Connect supply wires to terminal block where
indicated and connect ground wire to baseplate with
ground screw.
Connections:
a. Connect the live wire (black) to the terminal
block marked “L”.
b. Connect the neutral wire (white) to the terminal
block marked “N”.
Note that the colour of live and neutral wires depends
on voltage of supply service.
5. Replace cover screens. Do not over-tighten.
Business2
3
JetDryer Business2 instructions_Oct15_Layout 1 18/07/2016 1:30 pm Page 3

Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
Recommended Mounting Heights
Consumables
Operation
• No touch operation.
• Shake excess water from hands.
• Place hands into the aperture.
• Move hands up and down.
• Green LEDs count down drying time.
• Stops automatically after hands are removed,
or after 30 seconds.
Men’s Ladies Children, ages 11-17 Children, ages 3-10 Disabled
13” 11” 10” 6” 4”
350 mm 300 mm 250 mm 150 mm 100 mm
Product Order Code
JDBUSI2-AF
Moisturising Gel JDBUSI2-GEL
Anti Bacterial Filter
The Anti Bacterial Filter is tted to ensure dust and
airborne bacteria are restricted from entering the internal
components and airow of the dryer. The lter should
be replaced every 3 - 6 months, depending on usage.
Gels
JetDryer Gels perform 3 jobs in one:
1. Moisturise the hands.
2. Sanitise the product internally, and the users hands.
3. Fragrances the surrounding washroom area whilst in use.
The Gels are manufactured from natural sources and are
chemical free.
5. Disassemble
rinse clean usi
then replace. M
should be rep
Cleaning and
Periodic cleanin
ensure optimum
• Switch to servic
the dryer.
• Wipe the cover
solution. Do not
the cover.
Place Gels
here
4. Clean lter c
damp cloth. Re
lter every 3 - 6
into place
Business2
JetDryer Business2 instructions_Oct15_Layout 1 18/07/2016 1:30 pm Page 4

bled
m
e
AF
GEL
1. Pour a cup of water
down drain hole. Use
cleaning brush supplied
to clean drain hole.
2. Remove water tank
and empty.
5. Disassemble water tank and
rinse clean using a disinfectant,
then replace. Moisturising gels
should be replaced every month.
6. Wipe down the external
surfaces of the hand dryer
with a soft cloth. Switch
power back on and test
operation.
Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
Cleaning and Maintenance Instructions
WARNING
• Never spray water directly onto hand dryer
• Never use any abrasives or harsh chemicals
Periodic cleaning of the unit is recommended to
ensure optimum performance.
• Switch to service mode located on the top left side of
the dryer.
• Wipe the cover with a soft cloth and a mild cleaning
solution. Do not Soak. Never use abrasives to clean
the cover.
Place Gels
here
4. Clean lter casing by wiping with soft
damp cloth. Replace the antibacterial
lter every 3 - 6 months. Slide lter back
into place
Business2
JetDryer Business2 instructions_Oct15_Layout 1 18/07/2016 1:30 pm Page 5

Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
Diagram
Parts List
Warranty
Key Descripti
1Cover
2Fan house
3LED light
4Fan house
5Air outlet
6Eradiating
7Left side b
8Incept scr
9Lighting s
10 Air outlet
11 Door of p
12 Fan house
13 Display sc
14 Sensor lig
15 Sensor PC
16
17 Lighting P
Left xer
1 year warrant
18 Fan house
19 Switch bu
20 USB port
Business2
JetDryer Business2 instructions_Oct15_Layout 1 18/07/2016 1:30 pm Page 6

Operating Instructions and Parts Manual
Surface Mounted High Speed Hand Dryer
Parts List
Warranty
Key Description Product Code
1Cover HD-BB7023159-01
2Fan house cover HD-BB7023159-02
3LED light HD-BB7023159-03
4Fan house cover HD-BB7023159-04
5Air outlet HD-BB7023159-05
6Eradiating screen HD-BB7023159-06
7Left side board HD-BB7023159-07
8Incept screen HD-BB7023159-08
9Lighting screen HD-BB7023159-09
10 Air outlet HD-BB7023159-10
11 Door of power switch HD-BB7023159-11
12 Fan house cover HD-BB7023159-12
13 Display screen ornament HD-BB7023159-13
14 Sensor light PCB HD-BB7023159-14
15 Sensor PCB module HD-BB7023159-15
16 HD-BB7023159-16
17 Lighting PCB module
Left xer
Right xer
1 year warranty
HD-BB7023159-17
18 Fan house cover HD-BB7023159-18
19 Switch button HD-BB7023159-19
20 USB port HD-BB7023159-20
Key Description Product Code
21 Bracket HD-BB7023159-21
22 Big pothook HD-BB7023159-22
23 Fixing board HD-BB7023159-23
24 Small pothook HD-BB7023159-24
25 PP seal board HD-BB7023159-25
26 HD-BB7023159-26
27 Connector HD-BB7023159-27
28 Base plate HD-BB7023159-28
29 Hose HD-BB7023159-29
30 Motor PCB HD-BB7023159-30
31 Right side board HD-BB7023159-31
32 Filter HD-BB7023159-32
33 Water tank HD-BB7023159-33
34 Lock HD-BB7023159-34
35 Heater HD-BB7023159-35
36 Passage HD-BB7023159-36
37 Motor cover HD-BB7023159-37
38 Fan house module HD-BB7023159-38
39 Motor bracket HD-BB7023159-39
40 Motor module HD-BB7023159-40
Business2
JetDryer Business2 instructions_Oct15_Layout 1 18/07/2016 1:30 pm Page 7

JetDryer Business2 instructions_Oct15_Layout 1 18/07/2016 1:30 pm Page 8