Jide PURE 58/47 Reference manual

Jidé s.a. –Rue des Meuneries 11 –B-4650 HERVE (Belgique) –Tél. [phone] –Fax [phone] –www.jide.be - [e-mail]
PURE (EN) June 2018
MANUAL FOR INSTALLATION, USE AND
MAINTENANCE
PURE Full automatic
PURE Manual
Congratulations!
You have chosen an appliance of the Jidé range and we would like to thank you for it. We
are convinced that it will bring you warmth and comfort. In order to derive the greatest
benefit from your fireplace, we greatly stress the importance of following the instructions
and recommendations given in this notice.

Jidé s.a. –Rue des Meuneries 11 –B-4650 HERVE (Belgique) –Tél. [phone] –Fax [phone] –www.jide.be - [e-mail]
PURE (EN) June 2018
2
TABLE OF CONTENTS
INTRODUCTION ...................................................................................................................................... 3
General............................................................................................................................................................ 3
Technical characteristics and compliance .......................................................................................................... 4
Additional parts –Identification plate............................................................................................................... 6
USER NOTICE .......................................................................................................................................... 6
Starting a fire ................................................................................................................................................... 6
Combustion ..................................................................................................................................................... 7
The wood –Choice and usage........................................................................................................................... 9
INSTALLATION NOTICE.......................................................................................................................... 11
Preparation –Arrangements........................................................................................................................... 11
Fitting ............................................................................................................................................................ 13
Fitting of the finishing frame (option)...................................................................................................................................... 13
Fitting of the chimney connection ........................................................................................................................................... 14
Fitting of the connection for the convection air (option) ........................................................................................................ 14
Fitting of the combustion air intake......................................................................................................................................... 15
Electrical connection ...................................................................................................................................... 16
Vermiculite removing ..................................................................................................................................... 17
Ventilation access..................................................................................................................................................................... 17
Manual setting air inlet access................................................................................................................................................. 18
Automatic thermostat access .................................................................................................................................................. 18
MAINTENANCE OF THE FIREPLACE ........................................................................................................ 19
Cleaning –Chimney sweeping......................................................................................................................... 19
TROUBLESHOOTING.............................................................................................................................. 21
Causes - Advice .............................................................................................................................................. 21
DECLARATION OF CONFORMITY JIDÉ .................................................................................................... 23
CE MARKING ........................................................................................................................................ 24
PRODUCT FICHE –EU 2015/1186........................................................................................................... 25
WARRANTY .......................................................................................................................................... 25
Warranty agreement...................................................................................................................................... 25

Jidé s.a. –Rue des Meuneries 11 –B-4650 HERVE (Belgique) –Tél. [phone] –Fax [phone] –www.jide.be - [e-mail]
PURE (EN) June 2018
3
INTRODUCTION
General
To obtain optimum operation of your fireplace in complete safety, we recommend having it
installed by a specialist who will do the work professionally.
The responsibility of Jidé relates to the supply of the appliance. The installation is the
responsibility of the owner who must have it done according to the requirements of this
notice, and in accordance with the applicable regulations and standards of the different
countries governing the installation, insulation and connection of closed wood-burning
fireplaces, in new and old constructions, as well as smoke flues. The appliance may not be
modified as it could present a real danger and will invalidate the warranty.
A list of our dealers-installers is available on our site www.jide.be/en.
Before using your fireplace for the first time and in order to guarantee its good usage and
operation over time, we suggest you carefully read these instructions for use in order to
familiarise yourself with its various functions and characteristics.
Before starting your first fire, please ensure that no material required for the installation is
in the fireplace.
The paint has not been cured and will consequently harden when used for the first time,
causing the release of smoke and odours. We advise you to make a very strong fire and then
ventilate the room well.
Each Pure model is available in two versions: with manual or automatic thermostat. The Pure
range comprises the following models:
PURE 58/47
PURE 67/51
PURE 70/70
PURE 77/51
PURE 77 XL –only available in manual version
PURE 16/9

Jidé s.a. –Rue des Meuneries 11 –B-4650 HERVE (Belgique) –Tél. [phone] –Fax [phone] –www.jide.be - [e-mail]
PURE (EN) June 2018
4
Technical characteristics and compliance
Combining ecology and economy, Jidé has created the Pure range which has an external
combustion air inlet (sealed appliance).
The primary air arrives under the grate and the stainless steel canals to foster fire-lighting in
the fireplace.
The preheated secondary air creates post-combustion by reburning the gases, and this
greatly improves the efficiency.
The preheated tertiary air has a “turbo” effect, sweeping the glass from top to bottom to
keep it clean and creates a sufficient supply to feed the fire without primary air.
Ecological solution: cleaner emissions, less dust and CO
Economic: greatly reduced wood consumption.

Jidé s.a. –Rue des Meuneries 11 –B-4650 HERVE (Belgique) –Tél. [phone] –Fax [phone] –www.jide.be - [e-mail]
PURE (EN) June 2018
5
Jidé subjects its ranges of inserts to tests in approved laboratories so that they meet the
requirements of the European EN standards on safety and efficiency while limiting
CO emissions.
Test results according to the standards: EN 13229:2001 - EN 13229/A1:2003 –
EN 13229/A2:2004
PURE 58/47
Nominal power: 6 kW
Nominal efficiency: 79,4 %
CO emissions: 0,09 %
Fuel: wood
PURE 67/51
Nominal power: 8 kW
Nominal efficiency: 79,4 %
CO emissions: 0,09 %
Fuel: wood
PURE 70/70
Nominal power: 9,5 kW
Nominal efficiency: 79,4 %
CO emissions: 0,09 %
Fuel: wood
PURE 77/51
Nominal power: 9,4 kW
Nominal efficiency: 79,4 %
CO emissions: 0,09 %
Fuel: wood
PURE 77 XL
Nominal power: 12.9 kW
Nominal efficiency: 80,2 %
CO emissions: 0,08 %
Fuel: wood
PURE 16/9
Nominal power: 13 kW
Nominal efficiency: 79,4 %
CO emissions: 0,09 %
Fuel: wood
Characteristics of the PURE
You may face two specific cases:
1No possibility or necessity of an external combustion air inlet: Remove the air box front
side, which allows to take combustion air in the room. Leave also the back air inlet open.
PURE PURE MANUAL
2Plug the external air inlet to the back of the short stainless steel or to the bottom
(remove the plate and fill the back inlet). In this case, keep the air box face.

Jidé s.a. –Rue des Meuneries 11 –B-4650 HERVE (Belgique) –Tél. [phone] –Fax [phone] –www.jide.be - [e-mail]
PURE (EN) June 2018
6
Additional parts –Identification plate
In addition to the fireplace, the packaging contains the following elements:
- A poker;
- A cold handle;
- A glove;
- A speed controller to regulate ventilation (for fireplaces with ventilation);
- A short stainless steel duct 45° right-angled for the smoke link;
- A plate and a fixing screw (to fill the air inlet on the back in case of connection from
the bottom);
- A paint spray for eventual retouching. Attention: before using the fireplace, make
sure to get the spray out and to keep it away with a minimum distance of 2 m.
- On the packaging, instructions for use with identification plate.
All the Jidé fireplaces are registered as soon as they leave production, according to the
information contained on a plaque that accompanies this notice, stating in particular the
power, efficiency and CO emissions of the appliance.
This plaque must be kept and will enable your appliance to be identified in our files
(traceability) if necessary. We advise you to paste it on this user and installation notice or on
your invoice. USER NOTICE
Starting a fire
Before lighting, remove ashes especially on the stainless steel canals.
Do not exceed the maximum loading authorized (see page 10).
IMPORTANT actions before starting your fire:
1For the correct use of the appliance, the door must be opened slightly for 15 minutes -
the time necessary to reach a sufficient temperature in the fireplace.
2When the window is hot, please close the door. Combustion air inlet is regulated by the
automatic thermostat to obtain reduced wood consumption with respect to the heat
recovered. When the fireplace is hot, fans start automatically. For devices with manual
thermostat, you have to reduce the air inlet according to the wished heat.

Jidé s.a. –Rue des Meuneries 11 –B-4650 HERVE (Belgique) –Tél. [phone] –Fax [phone] –www.jide.be - [e-mail]
PURE (EN) June 2018
7
CAUTION
-For good performance do not remove completely the ashes of the stove.
-When the fire needs a reloading, set the speed controller on minimum. Open slightly
the door in order to avoid reverse flow of smokes in the room. After loading, do not
forget to position ventilation on the desired position.
-If you have a device with ventilation, never make it work without ventilation!
In case of momentary power failure, reduce the load and keep a medium heat.
Devices without ventilation MUST be decompressed in opening the two hot air outlet
and fixing 2 ducts of at least 1 meter (on the right and left side of the fireplace).
-The fireplace is designed to a door-closed use, after starting the fire. Reload when only
glowing embers remain.
-We advise you to use fire starter cube which facilitate a quicker and cleaner wood
combustion.
-Do not use inflammable liquid products.
Combustion
Combustion air
Combustion air is settled by an automatic thermostat, which regulate the working speed of
your fireplace, after started.
Thanks to the temperature sensor (on the right side of the device), the thermostat
automatically settle the coming of air, by opening of closing the air inlet. The thermostat is
not influenced by the room temperature. It only settles the one of the fireplace (which will
depends on the speed of the fans). It is therefore normal that if the temperature of the
fireplace is high, the valve will be closed whatever the control switch and the temperature of
the room are.
For fireplaces with manual thermostat, it is up to you to set the air inlet according to the
desired heat.
Convection air
Originally, your appliance operates with ventilation controlled by a speed controller and an
airstat. Depending on the chosen position, the speed controller determines the forced hot
air flow outside your fireplace (maximum power heating is reached with ventilation on the
highest level).
The airstat (on the left side of the device) is an accessory which turns on and off ventilation
according to temperature sensor. This ventilation turns on once the fireplace has reached a
certain temperature. Ventilation must always turn when the fireplace is hot, otherwise the
fans will be degraded. Hot air outlet will allow a hot convection air distribution in the room

Jidé s.a. –Rue des Meuneries 11 –B-4650 HERVE (Belgique) –Tél. [phone] –Fax [phone] –www.jide.be - [e-mail]
PURE (EN) June 2018
8
of the fireplace or in another room. If you have this type of installation, it is essential to take
advice from your approved installer.
There is an option "strop air" which fosters the hot convection air distribution through other
holes, by filling the convection air outlet on the top of the fireplace.
Devices without ventilation MUST have 2 hot air outlets with a finishing grid (not included).
These 2 hot air outlets must be plugged to at least 1 meter flexible diameter 125 mm.
The chimney
The smoke produced by the wood combustion is removed through the chimney flue.
The draft of the chimney reduces the pressure in the fireplace, which removes a part of the
smoke and supplies the combustion.
- A good draft will result in a high temperature difference between the inside of the
chimney and the outside of the house.
- Too great a draft will not enable a high enough temperature to be reached for good
combustion.
- Too small a draft will lead to a risk of reverse flow, fouling of the window and sooting of
the chimney.
An approved chimney sweep should be consulted for any questions regarding the good use
and maintenance of the chimney.
General recommendations
- For devices with an automatic thermostat, it is not recommended to greatly reduce the
operation of the fireplace to such a point that there are no flames, a sign of poor
combustion (speed of the fan too low). The unburned gases are converted into soot.
- In the same way, if overloaded your fireplace will not provide any additional comfort
and will lead to a reduction of efficiency, a pointless increase in the consumption of
wood, a loss of heat and abnormal wear of your fireplace.
- Certain weather conditions (strong wind, fog) may affect the combustion and draft of
the chimney and the air intake will have to be adjusted.
- When removing the ash, pay attention to the persistent presence of embers.
- In the event of a chimney fire, the door must be closed.
- NEVER use flammable liquid products (ex: methanol) to light the fire or reactivate the
fire!

Jidé s.a. –Rue des Meuneries 11 –B-4650 HERVE (Belgique) –Tél. [phone] –Fax [phone] –www.jide.be - [e-mail]
PURE (EN) June 2018
9
The wood –Choice and usage
The Jidé fireplaces are designed to burn hard wood logs only.
The quality of wood is important.
“Green” wood contains a lot of water (approx. 50 %).
“Dry” wood, kept outside for 24 months covered and well ventilated, still contains 15 %
water.
Damp wood is more difficult to consume, presents a lower calorific power and pollutes the
environment.
Damp smoke has disadvantages, for example a reduced draft and the formation of tar in the
flue and on cold surfaces (the window for example).
Split wood presents better combustion and will improve the operation of your fireplace.
The calorific value of wood depends on its type, and the volume of wood required for the
same quantity of heat differs according to this choice. Thus, the “hard” wood varieties such
as beech, oak, whose density is high, will require a lower quantity than other low density
species:
Density
Hornbeam ........................................................................................ 400 –500 kg per m³
Oak................................................................................................... 380 –480 kg per m³
Beech ............................................................................................... 350 –450 kg per m³
Birch................................................................................................. 300 –400 kg per m³
Poplar .............................................................................................. 250 –350 kg per m³
Ideal rate : 15 %
Energy efficiency
Moisture level

Jidé s.a. –Rue des Meuneries 11 –B-4650 HERVE (Belgique) –Tél. [phone] –Fax [phone] –www.jide.be - [e-mail]
PURE (EN) June 2018
10
Loading of the fireplace with wood:
PURE 58/47..........................................................2,3 kg (maximum) of dry wood per hour
PURE 67/51.............................................................3 kg (maximum) of dry wood per hour
PURE 70/70.............................................................3 kg (maximum) of dry wood per hour
PURE 77/51.............................................................3 kg (maximum) of dry wood per hour
PURE 77 XL...........................................................3,5 kg (maximum) of dry wood per hour
PURE 16/9............................................................ 3,5 kg (maximum) of dry wood per hour
CAUTION
**************************************************************************
The overloading of wood of your stove may have some consequences and the damage
hereafter will obviously not be covered by the warranty:
Deformation of the baffle;
Bleaching of the glass;
Degradation of the vermiculite;
Accentuated noise of the ventilator;
Deterioration of the automatic thermostat and of the airstat;
Excessive dilation of the door being able to involve a deformation of this one.
***************************************************************************
Moreover, we recommend you:
Not to burn resinous or treated wood (e.g. painted wood) or any other material containing
toxic products harmful to the environment, or which are aggressive for the components of
the fireplace.
To only burn heating wood, your fireplace is not designed to be used as an incinerator.
Not to overcome the calorific value of wood. Pay attention to the calorific value of
compressed logs. Half a compressed log at a time.