Jinling FO-75S1fOL User manual

30" OSCILLATING PEDESTAL FAN
OWNER'S MANUAL
AIR
CIRCULATOR
CAUTION
WARNING
RULES FOR SAFE OPERATION
:
:
:
Read and follow all instructions before operating fan.
Do not use fan if any part is damaged or missing.
- To reduce the risk of fire or electrical shock, do not expose to water or rain.
- To reduce the risk of fire or electrical shock, do not use this fan with any solid state
speed control device.
- Automatically operated device - To reduce the risk of injury, disconnect from power
supply before servicing.
- If the power supply cord is damaged, contact your local service centre or a qualified
electrician to install an appropriate replacement cord to prevent any injury or damage.
- The appliance does not apply to be used in locations where special conditions prevail,
such as the presence of a corrosive or explosive atmosphere ( dust, vapour or gas ).
- This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
1. Never insert fingers or any other objects through the grill guard when fan is in
operation.
2. Disconnect the fan from its power source when moving from one location to another.
3. Disconnect the fan from its power source when removing guards for cleaning.
4. Be sure fan is on a stable, flat surface when in operation.
5. Do not use fan in windows. Rain and moisture may create electrical hazard.
6. Close supervision is necessary when this fan is used near children, the elderly and
pets.
7. Do not place the fan near an open flame, cooking or heating appliance, or hot surface.
8. This fan should not be operated outside.
Do not alter the fan's assembly.
Be sure that both front and rear guard screws are completely tightened in
locking position before operation.
CAUTION:
WARNING:
COLUMN ASSEMBLY INSTRUCTIONS:
1. Attach coupling to the base with the screws as shown.
2. Loosen set k on the outer tube coupling and extend inner tube to desired height
tighten.
Set knob must be fully tightened before assembling the motor to the inner
tube.
nob
CAUTION:
FO-75S1fOL(2)
MODEL
10307
1

COLUMN / MOTOR ASSEMBLY INSTRUCTION:
GRILL / MOTOR ASSEMBLY
INSTRUCTIONS:
OPERATING INSTRUCTIONS
1. Align motor flange and column.
2. Insert the pivot bolt through the
motor flange, column and washer,
tighten firmly.
3. Insert smaller position screw
through bottom radius, attach
with washer, tighten firmly.
1. Unscrew the set screws from the
motor.
2. Set the rear guard in its proper position.
3. Attach the rear guard by inserting and tightening the set
screw to the motor ( through the eyelets on the guard ).
4. Insert the blade on the shaft until it reaches a stopping
point and the set screw is in line with the flat groove on
the shaft.
Be sure the set screw of your blade is facing the motor
of your fan. you may need to loosen the set screw at the
rear of the blade to slide easily onto the shaft.
5. Securely tighten the blade set screw.
DO NOT ALTER THE ANGLES OF BLADE.
6. Turn the clips on the front guard outward.
7. Mount the front guard with the groove at the guard's top sliding into its proper position
( the nameplate in its proper direction ).
8. Fastened and lightly tighten grille screws and washers on front guard and into back guard.
9. Press both front guard and back guard together.
10. Push front guard's clips downward into a locking.
11. Completely tighten grill screws washers on front guard and into back guard.
Loosen the position
screw first and then loosen the pivot bolt. Tilt motor to the desired angle then firmly
tighten the pivot bolt first and then tighten the position screw.
NOTE:
CAUTION:
TO ADJUST AIRFLOW UPWARD OR DOWNWARD:
●Loosen the screw on the
oscillation rod and move to the end of the
oscillation cam. Tighten the screw to lock the
position.
To oscillate the fan:
SETTING OSCILLATING MODE :
( )See Figure 1
●Loosen the screw
on the oscillation rod and move to the
center of the oscillation cam. Tighten the
screw again to lock the position.
Select air speed by setting switch to either high-low-off.
: Unplug from electrical supply source before cleaning.
1. Use soft damp cloth to clean, then wipe with dry cloth.
2. Do not use a cleaning solution that is harmful to paints or plastics.
3. Do not bend the blades.
To stop the oscillation:
WARNING
SPEED CONTROL:
CLEANING
ING
( )
: Disconnect from mains before
changing the setting.
Surges in electrical power or excessive heat may cause the fan
to turn off. Wait approximately 15 minutes for the fan to resume operation.
See Figure 2
CAUTION
IMPORTANT:
RAT
FO-75S1fOL(2) # 120V~ 60Hz 220W 1.9A10307
screw
fan motor
Figure 2
oscillation
cam
screw
fan motor
Figure 1
oscillation
cam
Set screw
Screw
Screws
Coupling
Base
Nut
Inner Tube
Outer Tube
Set Knob
Pivot Bolt
Position Screw
Connector
Flange
Plinth
Oscillation
cam
Screws
2
For Questions and Assistance, please contact us at:
http://www.help2uonline.com
3