JL Audio M-SWMCPv3-1.315 User manual

Installation Instructions for
M-SWMCPv3-1.315 • M-SWMCPv3-1.660 • M-SWMCPv3-1.900
M-SWMCPv3-2.000 • M-SWMCPv3-2.250
M-SWMCPv3-2.375 • M-SWMCPv3-2.500
PIPE MOUNTING FIXTURES (SWIVEL)
FOR ETXv3 ENCLOSED SPEAKER SYSTEMS
LIMI TED WARRANTY  MARIN E PRODUCTS USA
JL AUDIO warrant s this product to be free of defects in materials and workmanship for a period of t wo (2) years from the
original d ate of purchase.
This warranty is not tra nsferable and applies on ly to the origi nal pu rchaser from an author ized JLAUDIO dea ler. Should service
be necessar y under this warranty for any reason due to manufac turing defect or malfu nction, JL AUDIO will (at its d iscretion),
repai r or replace the defective product with new or rema nufac tured product at no charge. Damage caused by the following is not
covered u nder wa rranty: accident, misuse, abuse, product modification or neglect, fa ilure to follow i nsta llat ion instruc tions ,
unaut horiz ed repa ir attempts, misrepresentations by t he seller. This warr anty does not cover incidental or consequentia l damages
and does not cover t he cost of removing or reinstalling the un it(s). Cosmet ic damage due to accident or normal wear and tear is not
covered u nder wa rranty.
Any applicable i mplied warrantie s are li mited i n duration to the period of the ex press warra nty as provided herein begin ning
with the date of the origina l purchase at retail, and no wa rranties , whether express or implied, shall apply to this product
thereafter. Some states do not a llow limitations on implied warranties, therefore these exclusions may not apply to you. This
warr anty gives you specific legal rights, a nd you may a lso have other rights which vary from state to s tate.
For Service Information in the U.S.A. please call
JL Audio Customer Service:(9 5 4) 4 43-110 0
9:00 AM – 5:30 PM (Eastern Time Zone)
JL Audio, Inc
10369 North Commerce Pkwy.
Miramar, FL 33025, USA
International Warranties:
Produc ts purchased out side the United States of America are covered only
by that country’s dis tributor and not by J L Audio, Inc.
w w w . j l a u d i o . c o m
JL Audio® and the J L Audio logo are reg istered tradem arks of JL Audio, In c. “Ahead of the Curve ” and its respec tive logo is a trade mark of JL Audio, Inc .
©2014JLAu dio, Inc. • Formore de tailed infor mation please v isit us online at ww w.jlaudio.com. Due to our policy o f continuous pro duct develop ment, all speci fications ar e subject to chan ge without noti ce.
SKU# 011429
Printed in U.S.A. • 040815
For best adhesion, it is recommended to clean the inside
of the aluminum cap with acetone (not included), prior
to attaching it to the speaker enclosure. Apply a circular
bead of silicone adhesive (included) to the inside of the
aluminum logo cap, about 1/2-inch (13 mm) from the
outer edge.
17
Align the aluminum logo cap to the desired angle of
rotation, and press it onto the back of the enclosure.
Apply masking tape (not included) to hold the cap in
place until the silicone cures (at least 24 hours).
18
Remove adhesive backing and install the JL Audio logo
badge (Sport Grille Models Only).
13
If a dierent speaker angle is desired, remove the speaker
mounting screws and washers.
14
Rotate the enclosure to the desired angle, install the
5/16 - 18 x 1/2” set screw into the base of the xture, and
fully tighten.
16
Rotate the speaker to the desired angle. Reinstall the
speaker and speaker mounting screws and washers.
Hand-tighten the screws in a criss-cross pattern.
15

Have a helper support the enclosure during this step.
Use the supplied butt connectors to connect the red (+)
and black (-) speaker cable exiting the ETXv3 enclosure
to the speaker cable exiting the pipe. e green and white
wires will not be used in this application.
9
Adjust the angle of the xture until level, mark the
location for the speaker cable hole. Remove the xture
assembly, and drill a 1/2” hole on the mark.
5
Align the two upper halves of the xture around the pipe.
Hand-tighten four 1/4 - 20 x 1-1/4” machine screws with
1/4” lock washers into the xture. DO NOT TIGHTEN
FULLY AT THIS POINT.
11
Compress the base and two upper halves of the xture
together while pushing the fork out through the small
pin holes on the opposite side. Flip the fork, and
reinstall, along with the two #8 - 32 x 3/8” machine
screws and lock washers.
3
Remove the four 1/4 - 20 x 1-1/4” machine screws and
1/4” lock washers to separate the two upper halves of
the xture. Pass the speaker cable exiting the enclosure
through the opening on the underside of the xture.
7
Slide the excess speaker cable and the butt connectors
into the opening in the pipe as you raise the enclosure to
ush the xture to the pipe.
10
In applications that require the logo to be inverted,
remove the two #8 -32 x 3/8” machine screws and lock
washers.
2
For applications where the cable cannot be routed
through the pipe, the cable can be passed through one of
the openings on the side of the xture.
6
Remove one of the 1/4 - 20 x 1-1/4” machine screws
and 1/4” lock washers at a time. Apply Loctite® red
thread-locking compound (included), reinstall, and fully
tighten. Repeat the same process for the other three
screws. (Continued on reverse.)
12
Determine the speaker mounting location, and
temporarily secure the xture around the pipe by hand
tightening the four 1/4 - 20 x 1-1/4” machine screws and
1/4” lock washers.
4
Apply Loctite® red thread-locking compound
(included) to two 5/16” - 18 x 1-1/4” machine screws
(included), thread them into the base of the xture, and
push down on the xture to ensure no gap while fully
tightening.
8
Be sure the indicated stopping points are on opposite
sides of the xture as shown. e enclosure can rotate
up to 205.5 degrees in the clockwise direction, and 128.5
degrees in the counter-clockwise direction.
1
128.5 205.5
IMPORTANT: Swivel mounting xtures should only be
attached to horizontal pipes. ETXv3 enclosures should
only be mounted directly above (12 O’clock position) or
directly below (6 O’clock position) a horizontal pipe.
NOTE: The M-SWMCPv3-2.000 fixture and
M770-ETXv3-SG -WH Enclosed Speaker
System are used in this manual for illustrative
purposes only. The fixture installation steps
are the same for all ETXv3 Enclosed Speaker
Systems and all M-SWMCPv3 Swivel-Mount
Fixtures listed on front cover.
WARNING: Do not mount enclosures to a horizontal
pipe in any position other than directly above or directly
below.
WARNING: Never attach swivel mounting xtures to
vertical or angled pipes.
IMPORTANT WARNING
WARNING