JL Audio PS-SWMCP User manual

Installation Instructions for all
PS-SWMCP
swivel fixtures for round pipes
PIPE MOUNTING FIXTURES (SWIVEL)
FOR PS650VEX™ ENCLOSED SPEAKER SYSTEMS

Loosen the pre-installed M4 x 4 mm Set Screw in the
clamp receiver. Slide an M6 x 16 mm Machine Screw
through the center hole of the clamp receiver, into the
center hole in the xture base, and hand tighten.
1
Secure the clamps to the clamp receiver using a pair of
M6 x 45 mm Machine Screws, M6 Flat Washers, and M6
Locknuts as illustrated. e locknut should be installed
into the hex shaped recess on one end of each clamp.
Hand-tighten, allowing just enough freedom to rotate the
enclosure around the pipe.
3
Place the supplied plastic strip around the pipe to
prevent scratching. Push the clamps over the pipe
(remove the plastic strip). Align the clamps with the
clamp receiver on the enclosure.
2
Position the enclosure at the desired location, tightening
the M6 x 45 mm Machine Screws as necessary. Fully
tighten the pre-installed M4 x 4 mm Set Screw in the
clamp receiver to hold its position. Mark the location
of the clamps on the pipe, then remove the enclosure
from the pipe.
4

Apply Loctite® red thread-locking compound to two M6
x 16 mm Machine Screws, slide them through the slots
in the clamp receiver, into the appropriate holes in the
xture base, and fully tighten.
5
Realign the clamps with the clamp receiver on the
enclosure, and secure them to the clamp receiver using a
pair of M6 x 45 mm Machine Screws, M6 Flat Washers,
and M6 Locknuts as illustrated, and fully tighten. Note:
e locknut should be installed into the hex shaped
recess on one end of each clamp.
7
Remove the center M6 x 16 mm Machine Screw from the
clamp receiver, apply Loctite® red thread-locking
compound, reinstall, and fully tighten.
6
Remove adhesive backing and install the JL Audio logo
badge.
8

If you wish to rotate the speaker’s grille/logo badge
alignment, remove the six #8 x 1-1/4” speaker mounting
screws and #8 Flat Washers.
9
For best adhesion, it is recommended to clean the inside
of the aluminum cap with acetone (not included) prior to
attaching it to the enclosure. Apply a circular bead of
silicone adhesive to the inside of the aluminum logo cap,
about 1/2-inch (13 mm) from the outer edge.
11
Align the aluminum logo cap to the desired angle of
rotation, and press it onto the back of the enclosure.
Apply masking tape (not included) to hold the cap in
place until the silicone cures (at least 24 hours).
12
Rotate the speaker to the desired angle. Reinstall the
speaker and speaker mounting screws and washers.
Hand-tighten in a criss-cross pattern.
10

• For marine installations, do not connect the speaker’s
LED lights to the vessel’s navigational lighting circuits.
• For short-circuit protection, install a supplied fuse-
holder onto EACH speaker’s BLUE (+12V) LED power
connection lead.
• Connect all BLUE (+12V) leads together (parallel) and
connect to a switched +12V supply. Connect all
YELLOW (GND) leads together and connect to a
negative ground or to the NEGATIVE battery post.
• We recommend activating the speakers’ LEDs thru a
lighting circuit that supplies +12V via an existing switch.
If an existing switched circuit is not available, you may
install a dedicated toggle/rocker style switch that will
supply positive (+12V) power. Fuse this connection
according to how many LED circuits you have (LED
circuits x 150 mA).
[GND]
LED
[+12V]
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
LED
Fuse
Fuse
Fuse
[GND]
[+12V]
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
LED
LED
LED
LED
Fuse
Fuse
Fuse
Fuse
Fuse
For LED Models Only:
Example: One speaker pair of
LED circuits connected in parallel.
Example: Two speaker pairs of
LED circuits connected in parallel.

Mounting Fixture is made in the USA by Axia Alloys
Protected by US Patents #8,136,771 & #8,398,035
Included Hardware:
(hardware pictured for one)

NOTE: The PS-SWMCP-B-2.000 Fixture and PS650-VeX-SG-TMB Enclosed Speaker
System are used in this manual for illustrative purposes only. The fixture installation
steps are the same for all PS650-VeX Enclosed Speaker Systems and all PS-SWMCP
swivel fixtures for round pipes.
BOM ID Quantity Description
1 4 Axia Alloys Strap Clamp
26 M6 x 16 mm Socket Cap Machine Screw
3 2 M4 x 4 mm Set Screw (pre-installed)
4 4 M6 Nylon Insert Locknut
5 2 Clamp Receiver
6 1 Loctite® Red read-Locking Compound
7 4 M6 Flat Washer
8 4 M6 x 45 mm Socket Cap Machine Screw
9 1 Plastic Strip
10* 2 Fixture Base
11* 1 Silicone Adhesive
12* 12 #8 Flat Washer
13* 12 #8 x 1-1/4” Pan Head Screw
Note: Not all wires may be used in normal applications.
Wire Size Wire Color Use
16 AWG Red/Stripe Speaker Positive (+)
Black/Stripe Speaker Negative (–)
20 AWG
Red Not Used
Green Not Used
Blue LED Positive (+)
Yellow LED Negative (–)
* Included with VeX™ speaker enclosures.

LIMITED WARRANTY  MARINE PRODUCTS USA
JL AUDIO warrants this product to be free of defects in materials and workmanship for a period of two (2) years from the
original date of purchase.
This warranty is not transferable and applies only to the original purchaser from an authorized JLAUDIO dealer. Should service
be necessary under this warranty for any reason due to manufacturing defect or malfunction, JL AUDIO will (at its discretion),
repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not
covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions,
unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages
and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not
covered under warranty.
Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein beginning
with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product
thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For Service Information in the U.S.A. please call
JL Audio Customer Service: [phone]
9:00 AM – 5:30 PM (Eastern Time Zone)
JL Audio, Inc
10369 North Commerce Pkwy.
Miramar, FL 33025, USA
International Warranties:
Products purchased outside the United States of America are covered only
by that country’s distributor and not by JL Audio, Inc.
w w w . j l a u d i o . c o m
JL Audio® and the JL Audio logo are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
©2016 JLAudio, Inc. • For more detailed information please visit us online at www.jlaudio.com. Due to our policy of continuous product development, all specifications are subject to change without notice.
SKU# 011455
Printed in U.S.A. • 061316