JL Audio Stealthbox SB-KW-TRX4/10TW3 User manual

SB-KW-TRX4/10TW3 INSTR_SKU# 011451
Enclosure Type: Sealed
Driver Type: 10TW3-D4
Nominal Impedance: 2 ohms
Continuous Power Handling: 400 watts (RMS method)
INSTALLATION GUIDE
for the
SB-KW-TRX4/10TW3
SKU# 94624
2015 & Up Kawasaki Teryx 4
Continued on Next Page
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your
authorized JL Audio dealer. The installation professionals employed by your
dealer have the necessary tools and experience to disassemble and reassemble
your vehicle properly. If you prefer to perform your own installation, please read
this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely
vital that the Stealthbox®be properly mounted to the vehicle
according to these instructions. Failure to mount the enclosure
properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the
enclosure caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a
collision or sudden deceleration.
INSTALLATION
D IFFICU LT Y:
ESTIMATED TIME:
1 HOUR
25
OUT
OF

INCLUDED HARDWARE
Continued on Next Page
Page 2 • JL Audio, Inc., 2016
SB-KW-TRX4/10TW3 INSTR_SKU# 011451
Note: For optimum performance, JL Audio recommends applying the included Foam Strips (or sound damping material) to surrounding plastic panels to reduce unwanted vibrations.
BOM ID Qty SKU Description
1 1 153693 Bracket
2 2 153737 3/8” Stainless Steel Flat Washer
3 2 153731 3/8” Stainless Steel Serrated Spring Lock Washer
4 2 153730 3/8 - 16 x 1-1/4” Stainless Steel Serrated Flange Bolt
- 2 151345 Wax Squares (not shown)
- 2 150249 Foam Strips (not shown)

POWER RECOMMENDATION
JL Audio recommends high quality ampliers such as the JL Audio MX300/1. The diagram below shows the recommended crossover settings for the MX300/1. For a detailed description of the
amplier settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
CONNECTIONS
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using an 8 AWG power kit such as the XD-PCS8-1B for your
Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for
both channels of the amplier. JL Audio recommends using 12AWG speaker wire for subwoofers such as the XC-BCS12-25.
Continued on Next Page
Page 3 • JL Audio, Inc., 2016
SB-KW-TRX4/10TW3 INSTR_SKU# 011451

Page 4 • JL Audio, Inc., 2016 Continued on Next Page
STEP 6
From the backside of the rear panel, position
the Bracket around the frame. Slide a 3/8”
Serrated Spring Lock Washer and a 3/8” Flat
Washer over each of the 3/8 - 16 x 1” Serrated
Flange Bolts, thread the assemblies through
the holes in the Bracket and rear panel,
into the threaded inserts on the back of the
Stealthbox®, and fully tighten.
STEP 5
Connect speaker cable to the barrier strip on
the enclosure. Put the Stealthbox® back into
position.
STEP 4
Remove the Stealthbox® once more, leaving
the Wax Squares in place. Using a 3/8” drill bit,
drill a hole through the rear panel on each of
the impressions.
Before drilling, always make sure that you
are not going to be drilling into any gas
lines, brake lines, tires, transmission lines,
electrical wiring, exhaust systems or any
other critical system.
STEP 3
Temporarily place the Stealthbox® on the floor
behind the driver’s seat to determine where
the 3/8 - 16 x 1” Serrated Flange Bolts meet the
rear panel.
Remove the Stealthbox®, and position the Wax
Squares on the panel at the bolt locations. Put
the Stealthbox® back in position, pressing
firmly against the enclosure to leave bolt
impressions on the Wax Squares.
STEP 2
Thread the supplied 3/8 - 16 x 1” Serrated
Flange Bolts into the two threaded inserts on
the back of the Stealthbox®, and hand tighten.
STEP 1
Attach Foam Strips from one of the
included sheets to the rear and bottom of the
Stealthbox®, evenly spaced, as shown.
SB-KW-TRX4/10TW3 INSTR_SKU# 011451
STEP 7
Route speaker cable as necessary.
Note: For optimum performance, we
recommend applying Foam Strips from the
remaining sheet (or sound damping
material) to surrounding plastic panels to
reduce unwanted vibrations.

Page 5 • JL Audio, Inc., 2016
CONGRATULATIONS!
You have completed the installation for this model! Enjoy your new Stealthbox®!
SB-KW-TRX4/10TW3 INSTR_SKU# 011451
MID/HIGH FREQUENCY DRIVER FITMENT
VeX™ Enclosed Speaker Systems are ideal for powersports and o-road vehicle applications. Each
weatherproof pod can be mounted to a roll cage precisely aimed for optimum sound. Mounting
xtures are available to t a variety of roll cage diameters.
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, and “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc.,. “Ahead of the
Curve”, its respective logo, and “How we play” are trademarks of JL Audio, Inc.,.
Printed in USA • ©2016 JL Audio, Inc.,. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431
#6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending. For more detailed information please visit us online at www.jlaudio.com.
[phone]
www.jlaudio.com
JLA-SKU# 011451 • ver. 05.04.2016 • 10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA