JL Audio Stealthbox SB-P-CYNNE/10W6v2/BK User manual

INSTALLATION GUIDE
for the
SB-P-CYNNE/10W6v2/BK
SB-P-CYNNE/10W6v2/BK
2003 - 2006
2003 - 2006
Porsche Cayenne
Porsche Cayenne
Thank you for choosing a JL Audio Stealthbox®for your automotive sound system. With proper
installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox®installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage
extends to 1 year if your system is installed or approved by your authorized JL Audio dealer. If you
prefer to perform your own installation, please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox®be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
STEP 1
Remove any contents from the cargo area.
Continued on Next Page
STEP 2
Remove the flooring.
STEP 3
With a T-30 wrench or socket, remove the pair of hold down
cleats(A).
With an 10mm socket, remove the bolt(B) that secures the
side panel to the vehicle.
SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231
SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231
INSTALLATION
DIFFICULTY:
3
5
OUT
OF
ESTIMATED TIME:
23 HOURS
A
A
B

Continued on Next Page
SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231
SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231
STEP 7
Remove the plastic cover from the upper d-pillar trim.
Remove the phillip head screw that has been exposed .
STEP 6
Remove the top sill plate.
STEP 5
Remove the lower d-pillar trim.
STEP 4
Remove the bottom sill plate.
Page 2 • JL Audio, Inc 2007
STEP 9
With a T-30 socket, remove the bolt and metal bracket that
is located between the two rear seats.
STEP 11
Flip the driver’s side rear bottom cushion towards the front
of the vehicle.
STEP 10
Grab a hold of the back of the driver’s side rear seat as in
the picture.
Lift the right side of the seat up and out of the hinge
bracket.
Pull the left side of the seat towards the middle of the
vehicle, sliding the seat off of a hinge pin.
Once the seat is off both hinge points, remove the seat
from the vehicle.
STEP 8
Remove the upper d-pillar trim.

Continued on Next Page
SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231
SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231
STEP 15
Remove the plastic ring from the rear seat’s upper latch pin.
STEP 14
With a 17mm socket and ratchet, remove the seat belt
retracting unit.
STEP 13
Remove the trim panel.
STEP 12
Remove the plastic collar that is around the hinge pin.
Page 3 • JL Audio, Inc 2007
STEP 17
An airbag is located behind the c-pillar trim. Use caution
while removing this panel. All wiring/connections should be
protected.
As in the illustration, reach around to the rear of the c-pillar
trim and carefully remove the c-pillar trim from the c-pillar,
by pulling towards you.
STEP 19
From the driver’s side rear door opening. Pull the front of the
cargo side trim panel from the vehicle’s body. Do not fully
remove this side trim panel at this time.
STEP 18
With a T-25 socket remove the bolt that secures the front
of the side trim panel to the c-pillar.
STEP 16
Pull the SRS plastic badge from the upper c-pillar trim.
With a T-25 socket, remove the bolt that has been
exposed.

Continued on Next Page
SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231
SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231
STEP 23
With a T-30 socket, remove the bolts that secure the pocket
to the body of the vehicle.
STEP 22
Pull the side trim panel out of vehicle.
STEP 21
Pull the rest of the side trim panel from the body of the
vehicle.
Once the side trim panel is loose, disconnect the power
outlet 12V plug from the wire harness.
STEP 20
With a T-25 socket, remove three bolts that secures this
rear side trim panel.
Page 4 • JL Audio, Inc 2007
STEP 25
Place the supplied top mount plate into position. The plate
will only fit one way. The hole in the mounting plate will line
up with the access hole from the removed grommet.
STEP 27
Thread in one of the supplied socket cup set screws into the
bottom of the Stealthbox®, leaving 1-inch exposed.
STEP 26
Run speaker wire from the amplifier’s location to the
Stealthbox®location and check for proper operation of
the woofer.
STEP 24
Found in the rearmost driver’s side floor corner, remove
the rubber grommet in the cargo area.
Unsecure the wire harness from the wheel well.
*Make sure the ignition is not turned on*
Loosen the bolt that secures the brown wires to the
flooring of the vehicle.
Once loose, turn this wire assembly counter clockwise until
the wires are routed as illustrated in the picture. Secure the
bolt.

VEHICLE SHEET METAL
SOCKET CUP SET SCREW
HEX BOLT
BOTTOM MOUNTING PLATE
LOCK WASHER
FLAT WASHER
STEALTHBOX WALL THREADED INSERT
SOCKET CUP SET SCREW
TOP MOUNTING PLATE
COUPLER
Continued on Next Page
SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231
SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231
STEP 31
Place a supplied 3/8-inch lock washer and then a supplied
flat washer onto the supplied 3/8-inch bolts.
Place two of these mounting bolt assemblies through the
supplied L-bracket. The L-bracket can only be posistioned
one way. Line up the mounting holes of the L-bracket to the
threaded inserts of the Stealthbox®.
Place the L-bracket into the mounting position and guide the
bolt assemblies through the two holes in the metal lip, as
seen in the picture to the left.
Place a supplied flat washer and supplied hex nut onto each
protruding bolt, behind the metal lip.
With an 9/16-inch box end wrench holding the nuts, use a
9/16-inch socket to secure the L-bracket to the metal lip.
STEP 30
Once the Stealthbox® is in position, place the supplied piece
of black carpeting between the Stealthbox® and the rear side
of the wheel well. You need to cover the corner of the wheel
well just in front of the Stealthbox®.
STEP 29
Place the Stealthbox®into position by guiding the socket
cup set screw assembly through the hole in the top
mounting plate installed in STEP 25.
The bottom of the Stealthbox® will not touch the mounting
plate. The coupler will be touching the mounting plate.
STEP 28
Fully thread the supplied coupler to the first socket cup set
screw from STEP 27.
Thread the second supplied socket cup set screw into the
coupler.
Page 5 • JL Audio, Inc 2007
STEP 33
From under the vehicle, place the supplied mounting plate,
flat washers, lock washers and then hex nut onto the
protruding socket cup set screw. Using an 9/16-inch socket,
secure this bottom mounting assembly.
Note: For added protection, it is recommended that
you apply a bead of silicone between the vehicle and
the mounting plate. After the bolt assembly is tightly
secured, it is also recommended that vehicle under-
coating material is applied to the exposed assembly.
STEP 35
Reconnect the power outlet 12V plug to the wire harness,
unplugged in STEP 22.
STEP 34
Place the factory side trim panel, removed in STEP 22, back
into place.
STEP 32
With a 9/16-inch socket and the remaining supplied pair of
bolt assemblies, secure the L-bracket to the Stealthbox®.

Continued on Next Page
SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231
SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231
STEP 39
Replace the trim and the plastic collar that goes around the
hinge pin, from STEP 12 & 13.
STEP 38
With a 17mm socket, secure the seat belt retracting unit,
from STEP 14.
STEP 37
With a T-25 socket, secure the front of the side trim panel
to the c-pillar, from STEP 18.
STEP 36
With a T-25 socket, secure the rear of the side trim panel
to the d-pillar, from STEP 20.
Page 6 • JL Audio, Inc 2007
STEP 41
Secure the upper d-pillar trim to the d-pillar, secure the trim
with the mounting screw that was removed and repalce the
plastic cover, from STEPS 7 & 8.
STEP 43
Replace the lower d-pillar trim, from STEP 5.
STEP 42
Replace the top sill plate, from STEP 6.
STEP 40
With a T-25 socket, secure the top c-pillar trim to the
c-pillar, from STEPS 16 & 17.

SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231
SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231
STEP 47
Replace the flooring and any contents, from STEP 1 & 2.
CONGRATULATIONS
You have completed the installation for this model!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
STEP 46
Replace the rear seat removed in STEP 9 & 10.
STEP 45
With a T-30 wrench or socket, mount the pair of hold down
cleats(A), from STEP 3.
With a 9mm socket, mount the bolt(B) that secures the side
panel to the vehicle, from STEP 3.
STEP 44
Replace the cargo door sill plate, from STEP 4.
Page 7 • JL Audio, Inc 2007
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc.“Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU#011231-04-23-200
JLA-SKU#011231-04-23-200
7
7• Printed in USA • ©2007 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902
#6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign
patents pending. For more detailed information please visit us online at www.jlaudio.com.
[phone]
www.jlaudio.com
10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
INCLUDED HARDWARE
(2)
(2)
3/8-inch -16 x 2 1/4-inch Socket Cup Set Screws
3/8-inch -16 x 2 1/4-inch Socket Cup Set Screws
(7)
(7)
3/8-inch Flat Washer
3/8-inch Flat Washer
(1)
(1)
3/8-inch -16 Socket Cup Set Screw Coupler
3/8-inch -16 Socket Cup Set Screw Coupler
(5)
(5)
3/8-inch Lock Washer
3/8-inch Lock Washer
(1)
(1)
Aluminum Top Mounting Plate
Aluminum Top Mounting Plate
(4)
(4)
3/8-inch -16 x 1 1/4-inch Hex Bolts
3/8-inch -16 x 1 1/4-inch Hex Bolts
(1)
(1)
Aluminum Bottom Mounting Plate
Aluminum Bottom Mounting Plate
(3)
(3)
3/8-inch -16 Hex Nuts
3/8-inch -16 Hex Nuts
SPECIFICATIONS
Enclosure Type:
Acoustic Suspension (sealed)
Acoustic Suspension (sealed)
Driver Type:
10W6v2-D4
10W6v2-D4
Nominal Impedance:
2 ohms mono
2 ohms mono
Continuous Power Handling:
400 Watts
400 Watts
POWER RECOMMENDATION
JL Audio recommends using a high quality amplifier such as the JL Audio 500/1.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 500/1 when
being used to power your Stealthbox®.
+12VDC RemoteGround
JL AUDIO 500/1
five-channel system amplifier
+_
_
+
Subwoofer Output
MONO OUTPUT ONLY
40
45
55 65 85
120
200
Filter Freq. (Hz)
Mode / Slope
Off / 12dB / 24dB
Amp LP Filter
Infrasonic Freq. (Hz)
15
18
25 30 40
50
60
Off / 30Hz
Infrasonic Filter
0.5
0.7
1.1 1.6 2.7
4.3
"Q"
20
25
35 45 55
70
85
Center Freq.
0
+4 +10 +13
+15
Boost (dB)
Off / On
Bass EQ
Remote Bass Port
Advanced
Bass
Control
Preamp Output Section
Full Range / Amp Filter / Out Filter
Output Mode Filter Slope
12dB / 24dB
40
45
55 65 85
120
200
Filter Freq. (Hz)
Left Ch. Right Ch.
Filter Mode
LP / HP
Amplifier Input Section
Input Sens.
Left Ch. Right Ch.
Signal Sensing
Off / On
Input Voltage
Low / High
The JL Audio 500/1 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
MID/HIGH FREQUENCY DRIVER FITMENT
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location:
6.5-inch / Front Doors
6.5-inch / Front Doors
Fits JL Audio Models: TR650-CSi,
TR650-CXi, VR650-CSi, VR650-CXi, XR650-CSi, XR650-CXi,
TR650-CXi, VR650-CSi, VR650-CXi, XR650-CSi, XR650-CXi,
C5-650, C5-650x & ZR650-CSi
C5-650, C5-650x & ZR650-CSi
Rear Speaker Size / Location:
6.5-inch / Rear Doors
6.5-inch / Rear Doors
Fits JL Audio Models:
TR650-CXi, VR
TR650-CXi, VR
650
650
-CXi, C5-650x & XR
-CXi, C5-650x & XR
650
650
-CXi
-CXi
A
B
A