JL Audio Stealthbox SB-POL-SLINGSUBD/10W3v3-4 User manual

Enclosure Type: Sealed
Driver Type: 10W3v3
Nominal Impedance: 4 or 2 ohms
Continuous Power Handling: 500 watts (RMS method)
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your
authorized JL Audio dealer. The installation professionals employed by your
dealer have the necessary tools and experience to disassemble and reassemble
your vehicle properly. If you prefer to perform your own installation, please read
this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely
vital that the Stealthbox®be properly mounted to the vehicle
according to these instructions. Failure to mount the enclosure
properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the
enclosure caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a
collision or sudden deceleration.
INSTALLATION
D IFF IC U LT Y:
ESTIMATED TIME:
1 HOUR
Continued on Next Page
15
OUT
OF
SB-POL-SLINGSUBD/10W3v3 INSTR_SKU# 011482
INSTALLATION GUIDE
for the
SB-POL-SLINGSUBD/10W3v3-4
SB-POL-SLINGSUBD/10W3v3-2
SKU# 94637 (4 W)& 94638 (2 W)
2015-Up Polaris Slingshot

INCLUDED HARDWARE
Continued on Next Page
Page 2 • JL Audio, Inc., 2017
SB-POL-SLINGSUBD/10W3v3 INSTR_SKU# 011482
BOM ID Qty SKU Description
1 2 153814 8 - 32 x 1/2” Pan Head Phillips Machine Screw
2 1 153850 ABS Plate
3 2 153855 M6 - 1 x 50mm Hex Drive Flanged Button Head Screw
4 4 153858 Nylon Plastic Washer
5 2 153853 M6 - 1 x 25mm Hex Drive Flanged Button Head Screw
6 4 153856 M6 - 1 U-Nut
7 1 153848 Bottom Bracket
8 1 150285 Nylon Cable Tie
9 1 153847 Top Bracket
- 1 153857 3/4” x 3/4” EPDM Foam (not shown)
- 1 150249 Foam Tape (not shown)
Note: For optimum performance, JL Audio recommends applying the included Foam Strips (or sound damping material) to surrounding plastic panels to reduce unwanted vibrations.

POWER RECOMMENDATION
JL Audio recommends high quality ampliers such as the JL Audio MX500/1. The diagram below shows the recommended crossover settings for the MX500/1. For a detailed description of the
amplier settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
CONNECTIONS
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your
Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for
both channels of the amplier. JL Audio recommends using 12 AWG speaker wire for subwoofers such as our XC-BCS12-25.
Continued on Next Page
Page 3 • JL Audio, Inc., 2017
SB-POL-SLINGSUBD/10W3v3 INSTR_SKU# 011482

Page 4 • JL Audio, Inc., 2017 Continued on Next Page
STEP 8
From inside the storage compartment, pass
the Nylon Cable Tie through one of the inner
holes in the Top Bracket and ABS Plate, around
the front of the compartment latch, and back
through the opposite inner hole in the ABS
Plate and Top Bracket, into the storage
compartment, as shown.
STEP 7
Position the Top Bracket assembly behind the
rear plastic panel, with its center cutout around
the compartment latch, as shown. Position the
ABS Plate between the Top Bracket and the
compartment latch, aligning the holes in both
parts.
Secure with a pair of 8 - 32 x 1/2” Pan Head
Phillips Machine Screws, as shown.
STEP 6
Slide an M6 - 1 U-Nut over each of the outer
holes in the Top Bracket, as shown. Be sure the
U-Nuts are oriented downward.
STEP 5
Position the Bottom Bracket assembly behind
the hinge, under the storage compartment, as
shown. The center, flat section of the Bottom
Bracket should be placed against the rear
plastic panel. Center the Bottom Bracket below
the storage compartment opening.
STEP 4
Slide an M6 - 1 U-Nut over each of the outer
holes in the Bottom Bracket, as shown. Be sure
the U-Nuts are oriented outward.
STEP 3
Route speaker cable into the storage
compartment.
STEP 2
Open the storage compartment, and remove
the compartment door.
STEP 1
Slide the seat forward.
SB-POL-SLINGSUBD/10W3v3 INSTR_SKU# 011482

Page 5 • JL Audio, Inc., 2017 Continued on Next Page
STE P 14
Pictured is the Stealthbox fully installed.
Slide the seat back.
Note: For optimum performance, we
recommend applying the included Foam Strips
(or sound damping material) to surrounding
plastic panels to reduce unwanted vibrations.
STE P 13
Lift up on the enclosure, and fully tighten both
M6 - 1 x 50mm Hex Drive Flanged Button Head
Screws and both M6 - 1 x 25mm Hex Drive
Flanged Button Head Screws.
STE P 12
Slide a 1/4” Nylon Plastic Washer over each
of the two M6 - 1 x 25mm Hex Drive Flanged
Button Head Screws. Pass an assembly through
each of the holes in the bottom of the
enclosure, and thread it into the M6 - 1 U-Nut.
Do not fully tighten at this time.
ST E P 11
Slide a 1/4” Nylon Plastic Washer over each
of the two M6 - 1 x 50mm Hex Drive Flanged
Button Head Screws. Pass an assembly through
each of the holes in the top of the enclosure,
and thread it into the M6 - 1 U-Nut.
Do not fully tighten at this time.
STEP 10
Connect the speaker cable to the terminal cup
on the back of the enclosure, and slide the
Stealthbox® into the storage compartment.
STEP 9
With the Top Bracket in the horizontal position,
fully tighten the Nylon Cable Tie so that each of
the M6- 1 U-Nuts on the Top Bracket is aligned
with the factory holes in the rear plastic panel.
Remove the adhesive backing from the 3/4” x
3/4” EPDM Foam, and attach the foam to the
rear panel, above the storage compartment
opening, as shown.
SB-POL-SLINGSUBD/10W3v3 INSTR_SKU# 011482

Page 6 • JL Audio, Inc., 2017
MID/HIGH FREQUENCY DRIVER FITMENT
SB-POL-SLINGSPKRS/M770 speaker pods are also available for your vehicle. Each weatherproof pod is
designed for a perfect t and houses a premium JL Audio component system.
SB-POL-SLINGSPKR/M770
SKU# 94636
All specifications are subject to change without notice. “JL Audio®”and the JL Audio logo,“Stealthbox®” and the Stealthbox logo, and “How we play®” are registered trademarks of JL Audio, Inc.
“Ahead of the Curve” and its respective logo are trademarks of JL Audio, Inc.
Printed in USA • ©2017 JL Audio, Inc. • For more detailed information please visit us online at www.jlaudio.com.
[phone]
www.jlaudio.com
JLA-SKU# 011482 • ver. 05.23.2017 • 10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
CONGRATULATIONS!
You have completed the installation for this model! Enjoy your new Stealthbox®!
SB-POL-SLINGSUBD/10W3v3 INSTR_SKU# 011482
®