CONGRATULATIONS
You have completed the installation for this model!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
S T E P 6
Back out the socket cup set screws installed in STEP 1, to
expose 1 1/4-inch.
From under the vehicle, place a supplied fender washer,
flat washer, lock washer and then hex nut onto the socket
cup set screw and secure. Note: For added protection
it is recommended that you apply a bead of silicone
between the vehicle and the fender washer. After the
bolt assembly is tightly secured, it is also recommend-
ed that vehicle under-coating material is applied to
the exposed assembly
S T E P 5
With a drill and a 1/2-inch drill bit, drill through the
impression made in the wax squares. Note: Before drilling,
make sure that you are not going to be drilling into
any gas lines, brake lines, transmission lines, electrical
wiring, transfer case (4x4 vehicles) or anything else
that might cause a reduction in your weekly pay.
Always wear eye protection when drilling!
Remove the wax squares.
Run speaker wire from the amplifier’s location to the
Stealthbox®location and check for proper operation of
the woofer.
S T E P 4
Place the Stealthbox® into the mounting location and press
firmly onto the Stealthbox®.
Remove the Stealthbox® carefully, leaving the wax square
in place. The socket cup set screws will leave an impression
onto the wax square.
Page 2 • JL Audio, Inc 2007
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc.“Ahead of the Curve”and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU#011239 -09-06-2007 • Printed in USA • ©2007 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902
#6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign
patents pending. For more detailed information please visit us online at www.jlaudio.com.
(954) 443-1100
www.jlaudio.com
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
I N C L U D E D H A R D W A R E
(2) 3/8-inch -16 x 2-1/2-inch Socket Cup Set Screw (2) 3/8-inch -16 Hex Nut
(2) 3/8-inch Lock Washer (2) 3-inch x 3-inch Wax Square
(2) 3/8-inch Flat Washer
(4) 3/8-inch Fender Washer
S P E C I F I C A T I O N S
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 10W3v3
Nominal Impedance: 4 ohms mono
Continuous Power Handling: 600 Watts
P O W E R R E C O M M E N D A T I O N
JL Audio recommends using a high quality amplifier such as the JL Audio 500/1v2.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 500/1v2
when being used to power your Stealthbox®.
The JL Audio 500/1v2 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 6.5-inch / Front Doors
Fits JL Audio Models: TR650-CSi, TR650-CXi, VR650-CSi, VR650-CXi, XR650-CSi, XR650-CXi,
C5650, C5-650x & ZR650-CSi
Rear Speaker Size / Location: 5.25-inch / Rear Door
Fits JL Audio Models: TR525-CXi, VR525-CXi, VR525-CSi, C5-525x & C5-525
