JLab JBuds Air User manual

JBUDS AIR EARBUDS
AUTO-CONNECTING EARBUDS
Press and hold both touch sensors 3+ seconds to power ON.
One earbud turns solid white and the other earbud blinks blue/white indicating ready to pair to your device.
ADDING NEW /ADDITIONAL BLUETOOTH DEVICES:
Turn OFF Bluetooth from any previously connected device. Turn ON Bluetooth from new device. Take earbuds out of the case.
Earbuds will automatically enter Bluetooth Pairing. Select “JLab JBuds Air” in new device settings to connect.
FIRST TIME SETUP
1
CONNECTING TO BLUETOOTH
Select “JLab JBuds Air” in your device settings.
Voice prompt “Bluetooth connected” followed by solid white lights will indicate you are connected.
2
Press and hold
3+ seconds
Bluetooth
Settings
JLab JBuds Air
C
U
S
T
O
M
E
R
S
U
P
P
O
R
T
U
.
S
.
B
A
S
E
D
We love that you are rocking JLab!
We take pride in our products and fully stand behind them.
YOUR WARRANTY
All warranty claims are subject to JLab authorization
and at our sole discretion. Retain your proof of
purchase to ensure warranty coverage.
CONTACT US
Reach out to us at [email protected]
or visit jlab.com/contact
L
I
M
I
T
E
D
T
W
O
Y
E
A
R
REGISTER TODAY
jlab.com/register
Product updates | How-to tips
FAQs & more

Match the corresponding L and R
letters on the charging case for
proper charging. The earbuds
will auto power OFF and start
charging.
Blue lights will indicate earbuds
are charging and will turn OFF
when fully charged.
Earbuds will auto power ON and reconnect
to your device when taken out of the case.
RIGHT
EARBUD
LEFT
EARBUD
LEFT
EARBUD
RIGHT
EARBUD
VOLUME DOWN: Single tap
SIRI (iOS) or “OK GOOGLE”
(ANDROID): Double tap
ANSWER: Single tap
HANGUP: Double tap
REJECT INCOMING CALLS:
Press & hold 1+ sec
TRACK BACK: Press & hold 1+ sec
TURN ON: Press & hold 3+ sec
CHANGE EQ: Triple tap
(JBuds Air will cycle 3 EQ settings)
VOLUME UP: Single tap
ANSWER: Single tap
HANGUP: Double tap
REJECT INCOMING CALLS:
Press & hold 1+ sec
PLAY / PAUSE: Double tap
TRACK FORWARD: Press & hold 1+ sec
TURN ON: Press & hold 3+ sec
CHANGE EQ: Triple tap
(JBuds Air will cycle 3 EQ settings)
VOICE PROMPTS
“Ready to Pair”: JBuds Air are
ready to pair to Bluetooth device
“Bluetooth Connected”:
Earbud is connected to device
“Battery Full”: 100-75%
“Battery Medium”: 75-20%
“Low Battery”: Less than 25%
When power decreases to 10%,
“Low Battery” will play
BUTTON FUNCTIONS
Tap either the right or left earbud 3 times for different EQ settings (JBuds Air will cycle 3 EQ settings).
CUSTOM EQ3SOUND MODES
JLab SIGNATURE
JLab C3™ signature
sound with amplified
bass and vocals
BALANCED
Even sound with
no additional
enhancements
BASS BOOST
Amplified bass
and sub-bass
CHARGING EARBUDS
Connect the JBuds Air to computer
or USB 5V 1A (or less) output device.
LEDs pulse white when charging and
turn solid white when fully charged. OR
CHARGING CASE
1 2
TURN OFF EARBUDS WITHOUT CHARGING CASE:
Enter your Bluetooth device settings and disconnect the JBuds Air. Earbuds will power OFF after 3 minutes.

TROUBLESHOOTING
FITTING
Instructional videos at: JLAB.COM/MANUALS
ECHOES ON CALLS
If you experience microphone echo/call quality with the JBuds Air, make sure the Cush Fin is not blocking the microphone port.
Microphone open
Microphone covered
Try all the optional Cush Fins and
ear tips for best fit and proper seal.
The Cush Fin should be aligned by
positioning the contour around the
microphone hole.
Cush Fin™
Ear tip
TROUBLESHOOTING
NO AUDIO IN ONE EARBUD (MANUAL RESET)
Bluetooth
Settings
JLab JBuds Air i
Enter your Bluetooth device settings
and forget the JBuds Air.
Take both earbuds out of the
charging case. Wait for one of the
earbuds to turn solid white and
one to blink blue/white.
You are now ready to pair to your
Bluetooth device.
2
3
4
1
Open the charging case door and
leave both earbuds inside. Starting
with ONE earbud, quickly press the
button 7x times. Light will blink blue
4x times. Leave the earbuds in the
charging case.
Repeat with the other earbud.
Quickly press the button 7x times.
Light will blink blue 4x times.
Bluetooth
Settings
JLab JBuds Air
BLUETOOTH DEVICE DOES NOT CONNECT / RECONNECT
Enter your Bluetooth device
settings and forget the JBuds Air.
2On your device, turn OFF then
ON Bluetooth.
3
4
1
Bluetooth
Settings
Bluetooth
Settings
JLab JBuds Air i
Open the charging case and
wait for one earbud to turn
solid white and one to
blink blue/white.
Select “JLab JBuds Air” in
device settings to reconnect.

CAUTIONS
• Avoid extreme heat, cold, and humidity.
• Avoid dropping or crushing the earbuds.
• Wax may build up in the earbud tips, lowering the sound quality.
Carefully remove the wax with a cotton swab or other small tool to improve the sound quality.
• If you experience discomfort or pain, try lowering the volume or discontinuing use temporarily.
• If you experience regular discomfort while using this product, discontinue use and consult your physician.
• We recommend you treat your earbuds as you would a nice pair of sunglasses and keep them in safe location when not in use.
JLAB.COM
• Fully dry off the earbuds before putting in the charging case to
avoid any damage to the case. The earbuds are sweat/water
resistant but the case is not.
• Either earbud can connect to your device and be used
independently. Simply take out the earbud from charging case
and it will auto connect.
• Choosing the correct ear tip makes a significant improvement in
audio quality due to proper seal for the driver. Try all ear tips for
best results.
QUICK TIPS WARNING
Fully dry off the earbuds before
putting in the charging case to
avoid any damage to the case.
The earbuds are sweat/water
resistant but the case is not.
Shop products |Product alerts |Burn-in your headphones
JLab Store + Burn-in Tool