JLB Racing CHEETAH User manual

ShenZhen Golden cheetah technologyCo.,Ltd
WWW.jlbracing.cn
CHEETAH
INSTRUCTION MANUAL

Bright front LED
The gear box structure is easy to repair
All bearing throughout
Solid metal chassis
Sealed,tunable limited-slip differentials
Oil-filled ultra AL shocks with progressive dual-springs
Fully assembled and Ready-To-Race
Thank you for purchasing this JLB racing model.This manual contains
instructions on operating and maintaining the Cheetah .Please take a monent
to read through this manual to familiarize yourself with this model.
Tools lncluded
Requires
11
INTRODUCTION
Charger
Transmitter
Hex Key
4 PCS AAA Batteries
(For Transmitter)
Scale：1/10
Drive System:4WD
length:510mm
width:390mm
hight:210mm
wheelbase:310mm
Power Battery
FEATURES
PRODUCT CONTENTS
12mm
NOTE: not include

22
IMPORTANT INFORMATION
The Cheetah is a powerful RC car that will bring much
enjoyment.However,improper use can cause damage
and bodily injuries.Please read the following information
carefully to avoid casualties.
This model can be operated with Ni-MH or Lithium Polymer
batteries. Due to the battery’s high energy,density,please pay
attention to the following information to avoid injuries or
damages.
WARNING:

Front Bumper
Steer Block
Wheel Hex Hub
Body Mount Bracket
Chassis
Battery
Motor
Electronic Speed Control
Receiver
Servobuckle
Shock
Shock Stay
Down Suspension Arm
Tail wheel
Shock Stay
Motor Mount
33
Steering Servo
Turnbuckle(toe link)
LED Light
TOP Suspension Arm
Center Shaft
PARTS NAME
Tail Holder
Battery Tape
Motor lock
Second floor

44

55

Red wire “A”
Blue wire “B”
Black wire “C”
Servo Receiver
Power
Switch
Set Key
ESC
Motor
ELECTRONICS SRTUP
Hold the SET button
Red flashing, loosening
Neutral point Top polint of tjll throttle Top polint of tjll broke
Green LED flashes once Green LED flashes twice
Green LED
flaches thrice
66
Begin to use the new ESC
1.Connect the ESC,motor,receiver,battery
and servo according to the following diagram
The #A,#B,#C wires of the ESC can be connected
with the motor wires freely.If the motor runs in the
opposite direction,please swap any two wire
connections.
Note:You can use the transmitter to set the throttle
channel to the “Reverse”direction,and then the
motor will run oppositely.Please calibrate the
throttle range again after changing the direction of
throttle channel.
2.Throttle Range Setting(Throttle Range Calibration)
In order to make the ESC match the throttle range,you must calibrate it when you begin to use a new ESC,
or anew transmitter,or after changing the setting of the neutral position of throttle channel.ATV or EPA
parameters,otherwise the ESC cannot work properly.
1).Switch off the ESC, turn on the transmitter, set the
direction of throttle channel to “REV”,set the
“EPA/ATV” value of throttle channel to “100%”,and
disable the “ABS” brake function of your
transmitter.(Note1)
2).Hold the “SET”key and then switch on the ESC,
when the red LED begins to flash,release the key
immediately.
(Please check the picture on the right side)
3). Set the THREE points according to the
steps shown in the picture on the right side.
a)Neutral point
b)End point of forward direction
c)End point of backward direction
4). When the process of calibration is finished,
the motor can be started after 3 seconds.
Note1: If you don’t release the “SET”key
after the red LED begins to flash,the ESC
will enter the program mode,in such a case,
please switch off the ESC and re-calibrate the
throttle range again from step 1 to step 4.
NOTE:standby application

7
Front Suspensive Assembly
Front Gear Box Assembly
CORRECT
15X10X4
15X10X4
KM2.5X8

1.Fill shock body with 4/5 silicone fluid(purchase seperately),pump the shock shaft
up and down to remove any air bubbles.
2.Wait the air bubbles pumped out,then pull down the shock shaft to the bottom,fill
the silicone fluidup to 2 mm,after that,tighten the shock head1.
3.Install the spring,shock assemblingfinished.
Shock Assembling Steps:
8
Shock Assembly
Front Suspension Arms Assembly

9
Rear suspensive arm Assembly
Adjusting the Slipper clutch
NOTE: the slipper clutch adjustment too loose or tight
may result in damsge the gear during racing.
Tail wheels Assembly
127

10
Steering Assembly
Chassis Assembly
NOTE: Rotating the nut 98 to seek
suitable degree of tightness.
Motor Mount Assembly
NOTE: Adjustment 86 to seek
suitable degree of tightness.

11
ALL Assembly
TIPS:The slipper clutch adjustment short cut
Use wrench 10mm key,Insert the hold as the picture below.
Grasp the both sides of rear wheels,rotate in the same direction.

EA1001 EA1002 EA1003 EA1004 EA1005 EA1006
EA1007 EA1008 EA1011 EA1012
EA1013 EA1014 EA1015 EA1016 EA1017 EA1018
EA1019 EA1020 EA1021 EA1022 EA1023 EA1024
EA1025
EA1041
EA1029 EA1030
EA1031 EA1033 EA1034 EA1035 EA1036
EA1037 EA1038 EA1039 EA1040
x4
x1
x1
x4
EA1028
x1
x4
1212
SPARE PARTS
EA1009 EA1010
right x1
x4
PM3x12
x2
EA1026 EA1027
x2
EA1032
x1
x2x2 x2
x2
x1
x2
Down suspensive TOP suspensive
x2
x1
x2
x2
x2
x1
pM3x10
pM3x12
PM3x10
x2
x4
x4
x2
x2
x2
x2
x2
x2
x2
x2
x1
x10
x2
x4
x2
x2
4x50mm
3x30mm
x2
x4
x2
EA1042
x1
x1
x2
PM4X10
x4
PWM2.5X4
x1
x1
x2
x1
x1
x1
x1
x1
x2
KM3X12
PM3X12
PM3X116
x2
x2 PM3X10 x2
PM3X10
PIN3X17
IM3X3
x2 x2
PM3X8 x2
x2
PM3x12 PM3x10
x2
x2
x4
x1
left x1
x1
x1
pM3x10
x10
3.0mm
x4
x1
x2
x2 x2
x1 x1
x2
x4
x1
x1
im4x4
x2
x1
x2
x1
x1

EA1045 EA1046 EA1047
EA1043 EA1044
BE003
SPARE PARTS
EA1055 EA1056 EA1057 EA1058 EA1059 EA1060
EA1061 EA1062
EA1063
EA1066
BE001 BE002
x2
x1
x1
x2
x2
EA1048
EA1049
x10
iM4x4
EA1050 EA1051 EA1052 EA1053 EA1054
x1 x1 x2
FRONT
REAR
x1
x1
KM3X12
x2
x2x1
KM3X12 x3
x1
PM3X8 x4
x1
x1
KM2.5*8
x8
x1 x1 x1 x1
x1
x2
x2
pM3x12
pM4x12
x1 x1
x2
x2
M10
x1
80A
x1 x1
10x15x4
x4
5x10x4
x4
5x8x2.5
x4
x10 x10
SW001
pM3x24 pM3x16
SW002
x10
pM3x12
SW003
x10
pM3x10
SW004
x10
pM3x8
SW005
x1
EA1067
SPARE PARTS
11.1V-4000MAH
x10
1.0x7.8mm
PN001
EA1068
x4x4
EA1069
x1
x10
2.5x13mm
PN002
x10
3.0x117mm
PN003
x10
pM3x6
SW006
1213
EA1070
x1
EA1071
x2
EA1075
x8
EA1076
PM4X10
PWM2.5X4
x2
x4 x4
EA1077
x1
OP-gear-seat

1414
x10
SW007
KM4x10
x10
SW008
KM3x12
x10
SW009
KM2.5x8
x10
SW010
pM2.5x8
SW011
pwM2.5x4
x10
x10
SW014
pM4x10 pM4x12
x10
SW015
x10
IM4x4
x10
SW016 SW017
IM3X3
x10
M3 NYLON
NT001
x10
ID 3.0x2.0mm
x10
ID 4.5x1.5mm
OR002
x10
ID12x1.5mm
OR003
x10
ID 16x1.0mm
OR004
M10
x10
NT002
x10
SW012
KM4x20
x10
SW013
pM3x20
x10
3MM
EC001
x10
M5 NYLON
NT003 OR001
x10
10X5X0.3MM
SP001 EA1078
OP-dog-bone
x2
EA1080
3670-2500KV
x1
EA1081
21KG
metal Gear
SteeringServo
x1
SPARE PARTS
EC1009
upgrade X1
EA1082
X1

1515
Bill Of Material
2

1516
CHEETAH
1:10 Scale 4WD Brushless monster truck.
ProductFeature:
Superior metal chassis design
The whole kit strength is enhanced greatly, not afraid to general crash. It's crash worth mor
e
than 70% compared to common model cars. And the chasis is with strength metal second floor which
can protect the vehicle fram of impact resistance strength and prolong lifetime.
Tough Suspension
CHEETAH giving you the assurance that you'll be able to deal out the same abuse that all the other
nitro-powered trucks can handle! Beefy parts mean the CHEETAH can take plenty of abuse and
punishment, giving you plenty of big-air thrills.
Thick Super Heavy-Duty Dogbons
Extra-thick, super duty dogbones provide the insurance you'll want when you take the CHEETAH way
off-road and into rough country! The thick diameter, larger ends and sleek black anodizing add
up to all the assurance you'll want that the drivetrain won't let you down when the going gets
tough! You'll be able to commit the full power of the Brushless motor to the ground
without worrying about drivetrain breakages or anything else.
Big Bore Aluminum Shocks
Four huge Big Bore shocks give all the suspension action you need to get out and blast through
the roughest of tracks or off-road terrain. With slick aluminum bodies, they are lightweight and
strong, with almost no friction 'stiction' between the shock piston and shock body. The extra-large
capacity gives you extra control and damping action so you have the driving feel that makes off-road
driving so much fun!
CHEETAH Wheelie Bar
The Wheelie Bar is included as OP part, ready for you to bolt on in case you want to pull impressiv
e
wheelies. This design makes the car looks high-end. This car has a relaxed air or cartwheel stunt
s
and Turning somersault.Also, the special balance feature will not make the car overturned easily.
All-Terrain Tyres
With the aggressive tyres, you can go off-road to on-road with cool, predictable handling and
very little drama. The centre tread lines give you stability on paved surfaces while the side
treads and heavy-duty sidewall teeth grip any sort of dirt, mud, muck, leaves, etc.
High CG&High stability
He can easily through any terrain,The high CG gives you extra control and cornering ability,
allowing you to rule the corners on the track and pull off spectacular stunts to impress.
RTR
They are Ready-To-Run. Just a few steps are needed to get your car up and running. Ready-To-Run
models bring you the same high performance and quality.cheetah also could be a high end model
car kit, if you prefer.

Shenzhen Golden cheetah technology co;Ltd
WWW.Jlbracing.cn
Tel： [phone]
Fax：[phone]
Email contact：[email protected]
Address: 2F D-Building Jinhao pioneer Park Dafu Industrial Zone Guanlan city
Longhua new district Shenzhen China 518110