JLG 260MRT Installation and user guide

Service & Maintenance Manual
Model
260MRT
3121801
July 23, 2018 - Rev K

INTRODUCTION
3121801 A-1
SECTION A. INTRODUCTION - MAINTENANCE SAFETY PRECAUTIONS
GENERAL
This section contains the general safety precautions
which must be observed during maintenance of the
aerial platform. It is of utmost importance that mainte-
nance personnel pay strict attention to these warnings
and precautions to avoid possible injury to themselves
or others, or damage to the equipment. A maintenance
program must be followed to ensure that the machine is
safe to operate.
MODIFICATION OR ALTERATION OF AN AERIAL WORK PLATFORM
SHALL BE MADE ONLY WITH WRITTEN PERMISSION FROM THE MANU-
FACTURER.
The specific precautions to be observed during mainte-
nance are inserted at the appropriate point in the man-
ual. These precautions are, for the most part, those that
apply when servicing hydraulic and larger machine
component parts.
Your safety, and that of others, is the first consideration
when engaging in the maintenance of equipment.
Always be conscious of weight. Never attempt to move
heavy parts without the aid of a mechanical device. Do
not allow heavy objects to rest in an unstable position.
When raising a portion of the equipment, ensure that
adequate support is provided.
SINCE THE MACHINE MANUFACTURER HAS NO DIRECT CONTROL OVER
THE FIELD INSPECTION AND MAINTENANCE, SAFETY IN THIS AREA
RESPONSIBILITY OF THE OWNER/OPERATOR.
HYDRAULIC SYSTEM SAFETY
It should be noted that the machines hydraulic systems
operate at extremely high potentially dangerous pres-
sures. Every effort should be made to relieve any system
pressure prior to disconnecting or removing any por-
tion of the system.
MAINTENANCE
FAILURE TO COMPLY WITH SAFETY PRECAUTIONS LISTED IN THIS SEC-
TION COULD RESULT IN MACHINE DAMAGE, PERSONNEL INJURY OR
DEATH AND IS A SAFETY VIOLATION.
•ENSURE REPLACEMENT PARTS OR COMPONENTS ARE
IDENTICAL OR EQUIVALENT TO ORIGINAL PARTS OR
COMPONENTS.
•NO SMOKING IS MANDATORY. NEVER REFUEL DURING
ELECTRICAL STORMS. ENSURE THAT FUEL CAP IS
CLOSED AND SECURE AT ALL OTHER TIMES.
•REMOVE ALL RINGS, WATCHES AND JEWELRY WHEN
PERFORMING ANY MAINTENANCE.
•DO NOT WEAR LONG HAIR UNRESTRAINED, OR
LOOSE-FITTING CLOTHING AND NECKTIES WHICH ARE
APT TO BECOME CAUGHT ON OR ENTANGLED IN
EQUIPMENT.
•OBSERVE AND OBEY ALL WARNINGS AND CAUTIONS
ON MACHINE AND IN SERVICE MANUAL.
•KEEP OIL, GREASE, WATER, ETC. WIPED FROM STAND-
ING SURFACES AND HAND HOLDS.
•USE CAUTION WHEN CHECKING A HOT, PRESSURIZED
COOLANT SYSTEM.
•NEVER WORK UNDER AN ELEVATED SCISSOR UNTIL
PLATFORM HAS BEEN SAFELY RESTRAINED FROM ANY
MOVEMENT BY BLOCKING OR OVERHEAD SLING, OR
SAFETY PROP HAS BEEN ENGAGED.
•BEFORE MAKING ADJUSTMENTS, LUBRICATING OR
PERFORMING ANY OTHER MAINTENANCE, SHUT OFF
ALL POWER CONTROLS.
•BATTERY SHOULD ALWAYS BE DISCONNECTED DUR-
ING REPLACEMENT OF ELECTRICAL COMPONENTS.
•KEEP ALL SUPPORT EQUIPMENT AND ATTACHMENTS
STOWED IN THEIR PROPER PLACE.
•USE ONLY APPROVED, NONFLAMMABLE CLEANING
SOLVENTS.

INTRODUCTION
A-2 3121801
REVISION LOG
Original Issue A - April 13, 2000
Revised B - Jan 24, 2002
Revised C - April 22, 2004
Revised D - July 3, 2006
Revised E - Aug 30, 2006
Revised F - Oct 11, 2007
Revised G - April 28, 2008
Revised H - Dec 19, 2008
Revised I - Oct 20, 2011
Revised J - April 19, 2013
Revised K - July 23, 2018

3121801 i
TABLE OF CONTENTS
TABLE OF CONTENTS
SUBJECT - SECTION, PARAGRAPH PAGE NO.
SECTION 1 - SPECIFICATIONS
1.1 Operating Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.2 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.3 Component Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.4 Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.5 Lubrication Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.6 Cylinder Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.7 Pressure Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.8 Limit Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.9 Major Component Weights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.10 Critical Stability Weights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.11 Serial Number Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.12 Torque Charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
SECTION 2 - PROCEDURES
2.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2 Servicing and Maintenance Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.3 Lubrication Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.4 Cylinders - Theory of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.5 Valves - Theory of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.6 Component Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
2.7 Wear Pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
2.8 Cylinder Checking Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
2.9 Lift Cylinder Removal and Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2.10 Cylinder Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
2.11 Steer Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
2.12 Limit Switch Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
2.13 Pressure Setting Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
2.14 Drive Pump Start-up Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
2.15 Automatic Choke - Field Adjustment (DF-750). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
2.16 Joystick Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
2.17 Tilt Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
2.18 Calibrations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29
2.19 Electronic Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31
2.20 Flash Codes and Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35
2.21 Machine Model Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42
2.22 Machine Configuration Programming Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-43
2.23 Preventive Maintenance and Inspection Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44
SECTION 3 - GENERAL ELECTRICAL INFORMATION & SCHEMATICS
3.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2 Multimeter Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.3 Applying Silicone Dielectric Compound To Amp Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.4 Working With Deutsch Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3.5 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
3.6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
3.7 Electrical Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22

ii 3121801
TABLE OF CONTENTS
LIST OF FIGURES
FIGURE NO. TITLE PAGE NO.
1-1. Serial Number Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1-2. Lubrication Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1-3. Operating Temperature Specifications - Kubota . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1-4. Torque Chart (SAE Fasteners - Sheet 1 of 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
1-5. Torque Chart (SAE Fasteners - Sheet 2 of 5)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
1-6. Torque Chart (SAE Fasteners - Sheet 3 of 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
1-7. Torque Chart (SAE Fasteners - Sheet 4 of 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
1-8. Torque Chart (METRIC Fasteners - Sheet 5 of 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
2-1. Arms and Platform Positioning and Support, Cylinder Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2-2. Lift Cylinder Removal - Cylinder Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
2-3. Lift Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
2-4. Cylinder Barrel Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
2-5. Capscrew Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
2-6. Cylinder Rod Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
2-7. Tapered Bushing Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
2-8. Rod Seal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
2-9. Wiper Seal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
2-10. Installation of Head Seal Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
2-11. Piston Seal Kit Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
2-12. Tapered Bushing Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
2-13. Seating the Tapered Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
2-14. Poly-Pak Piston Seal Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
2-15. Rod Assembly Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
2-16. Steer Cylinder Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
2-17. Leveling Jack Assembly - (Prior to S/N 105371) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
2-18. Leveling Jack Assembly - (S/N 105371to S/N 141689) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
2-19. Leveling Jack Assembly - (S/N 141689 to Present). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
2-20. Valve Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
2-21. Leveling Jacks Directional Valve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
2-22. Automatic Choke Adjustment (DF-750) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
2-23. Joystick Controller - (JLG P/N 1600308). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
2-24. Joystick Controller - (JLG P/N 1600403). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
2-25. Tilt Sensor Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
2-26. Tilt Sensor Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
2-27. Tilt Sensor Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28
2-28. Tilt Sensor Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28
2-29. Hand Held Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31
2-30. Analyzer Flow Chart - Sheet 1 of 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37
2-31. Analyzer Flow Chart - Sheet 2 of 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38
2-32. Analyzer Flow Chart - Sheet 3 of 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39
2-33. Analyzer Flow Chart - Sheet 4 of 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-40
2-34. Analyzer Flow Chart - Sheet 5 of 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41
3-1. Voltage Measurement (DC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3-2. Resistance Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3-3. Continuity Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3-4. Current Measurement (DC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3-5. AMP Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3-6. Connector Assembly (1 of 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3-7. Connector Assembly (2 of 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3-8. Connector Assembly (3 of 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3-9. Connector Assembly (4 of 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3-10. Connector Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
3-11. Connector Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3-12. DT/DTP Contact Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

3121801 iii
TABLE OF CONTENTS
3-13. DT/DTP Contact Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3-14. HD/HDP Contact Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3-15. HD/HDP Locking Contacts Into Position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3-16. HD/HDP Contact Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3-17. HD/HDP Unlocking Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3-18. Electrical Schematic - Sheet 1 of 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
3-19. Electrical Schematic - Sheet 2 of 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
3-20. Electrical Schematic - Sheet 3 of 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
3-21. Electrical Schematic - Sheet 4 of 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
3-22. Electrical Schematic - (w/ Generator) - Sheet 1 of 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
3-23. Electrical Schematic - (w/ Generator) - Sheet 2 of 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27
3-24. Electrical Schematic - (w/ Generator) - Sheet 3 of 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28
3-25. Electrical Schematic - (w/ Generator) - Sheet 4 of 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29
3-26. Electrical Componants Installation - Prior to S/N 141689 - Sheet 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30
3-27. Electrical Componants Installation - Prior to S/N 141689 - Sheet 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31
3-28. Electrical Componants Installation - S/N 141689 to Present - Sheet 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32
3-29. Electrical Componants Installation - S/N 141689 to Present - Sheet 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33
3-30. Hydraulic Schematic - Prior to S/N 141689 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-34
3-31. Hydraulic Schematic - S/N 141689 to Present. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-35
3-32. Hydraulic Diagram (Generator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-36
3-33. Hydraulic Diagram (Leveling Jacks) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-37

iv 3121801
TABLE OF CONTENTS
LIST OF TABLES
TABLE NO. TITLE PAGE NO.
1-1 Operating Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1-2 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1-3 WG750-B Kubota Gasoline/LP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1-4 D905-B Kubota Diesel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1-5 D1005 Kubota Diesel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1-6 Tire Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1-7 Pump Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1-8 Hydraulic Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1-9 Lubrication Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1-10 Cylinder Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1-11 Pressure Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1-12 Major Component Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1-13 Critical Stability Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1-14 Lubrication Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
2-1 Cylinder Component Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
2-2 Holding Valve Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
2-3 Leveling Jacks Directional Valve Torque Specs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
2-4 Joystick Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
2-5 Joystick Plug Loading Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
2-6 Joystick Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
2-7 Joystick Plug Loading Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
2-8 Tilt Sensor Harness Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
2-9 Tilt Sensor Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28
2-10 Help Messages and Flash Codes - Software P1.X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35
2-11 Machine Model Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42
2-12 Machine Configuration Programming Information - Software Version P1.13 . . . . . . . . . . . . . . . . . . . . . . . . . . 2-43
2-13 Preventive Maintenance and Safety Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45
3-1 Elevation System Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
3-2 Chassis Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
3-3 Hydraulic System Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
3-4 Electrical System Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

SECTION 1 - SPECIFICATIONS
3121801 1-1
SECTION 1. SPECIFICATIONS
1.1 OPERATING SPECIFICATIONS 1.2 CAPACITIES
1.3 COMPONENT DATA
Engine
Table 1-1. Operating Specifications
MachineWeight 3701kg(8160lbs)
MachineHeight:
FullyElevated
Stowed
8m(26ft)
2.3m(7.5ft)
MachineWidth 1.8m(5.9ft)
MachineLength 2.7m(8.9ft)
PlatformRailingHeight 1.1m(43.5in.)
PlatformDimensions 2.59x1.65m(8.5x5.4ft)
PlatformCapacity 570kg(1250lbs)
PlatformExtensionCapacity 140kg(300lbs)
MaxTravelSpeed 4.5kmh(2.8mph)
MaxTravelGrade 35%
MaxSlope:
Side to Side
Fore & Aft
3°
5°
TurningRadius:
Inside
Outside
2.1m(6.9ft)
4.4m(14.4ft)
LiftSpeed:
Up
Down
32-34sec
21-27secs
MaxTireLoad 921kg(3300lbs)
MaxGroundBearingPressure 3.2kg/cm²(33psi)
MaxHydraulicsystemPressure 20.68Mpa(3000psi)
ElectricalSystemVoltage 12Volt
Wheelbase 2m(78in.)
GroundClearance 20.3cm(8in.)
MaxWindspeed 12.5m/s(28mph)
MaxHorizontalManualSideForce 400N(90lbf)
NumberofPersons 2
Table 1-2. Capacities
FuelTank 27.2L(7.2gal)
HydraulicOilTank 56.8L(15gal)
HydraulicSystem(includingtank) 68.1L(18gal)
EngineCrankcase:
Gasoline Engine
DieselEngine
3.25L(3.4qts)
4L(4.2qts)
EngineCoolant:
GasolineEngine
DieselEngine
4.7L(1.25gal)
5.7L(1.5gal)
Table 1-3. WG750-B Kubota Gasoline/LP
Type 3cylinder,liquid-cooled
Power 24.5horsepower@3600rpm
Idle 1500rpm
HighEngine 3600rpm
Alternator 40Amp
FuelConsumption:
Low RPM
High RPM
4.9Lph(1.3gph)
9Lph(2.4gph)
Table 1-4. D905-B Kubota Diesel
Type 3cylinder,liquid-cooled
Power 26horsepower@3000rpm
LowIdle 800rpm
HighEngine 3800rpm
Alternator 40Amp
FuelConsumption:
Low RPM
High RPM
2.6Lph(0.68gph)
5.5Lph(1.48gph)

SECTION 1 - SPECIFICATIONS
1-2 3121801
Tires
Pumps
Steer/Drive System
Tire - Pneumatic or foam filled - 26 x 12 15 lug
NOTE: Inflate pneumatic tire to 3.1 bar (45 psi)
Toe-In - Adjust to 12.7 mm (1/2 inch) overall
Drive Motor - Rexroth
Hydraulic Filter - Inline
Full flow paper filter (Cartridge type)
Torque Requirement
All wheel lug nuts should be torqued to 142 Nm (105 ft lb)
every 150 hours.
NOTE: When maintenance becomes necessary or a fastener has
loosened, refer to the Torque Chart in this section to deter-
mine proper torque value.
1.4 LUBRICATION
Hydraulic Oil
NOTE: Hydraulic oils must have anti-wear qualities at least to API
Service Classification GL-3, and sufficient chemical stability
for mobile hydraulic system service. JLG Industries recom-
mends Mobilfluid 424 hydraulic oil, which has an SAE vis-
cosity of 10W-30 and a viscosity index of 152.
NOTE: Aside from JLG recommendations, it is not advisable to mix
oils of different brands or types, as they may not contain
the same required additives or be of comparable viscosi-
ties.
1.5 LUBRICATION SPECIFICATIONS
Table 1-5. D1005 Kubota Diesel
Type 3cylinder,liquid-cooled
Power 23.5horsepower@3000rpm
BorexStroke 76.0mmx73.6mm
Displacement 61.08in3
LowIdle 800rpm
HighIdle 3800rpm
Alternator 12V, 30Amp
Starter 12V,1.0Amp
FuelConsumption 1.32Lph(0.35gph)
Table 1-6. Tire Specifications
Description (Standard) (Non-Marking)
Size 26x12-15
LoadRange 8Ply
Pressure 55psi
Table 1-7. Pump Specifications
Description Drive Pump Lift/Steer Pump
Type Piston Gear
MaxOutput 83.3lpm(22gpm)@3000rpm 18lpm(4.75gpm)@3000rpm
Displacement 28cm³/rev
(1.7in³/rev)
1.4cm³/rev
(0.36in.³/rev)
Table 1-8. Hydraulic Oil
HYDRAULIC SYSTEM OPERATING
TEMPERATURE RANGE SAE VISCOSITY GRADE
-18to-5°C
(0 to +23°F)
10W
-18to+100°C
(0 to +210°F)
10W-20,10W-30
+10to+100°C
(+50 to +210°F)
20W-20
Table 1-9. Lubrication Specifications
KEY SPECIFICATIONS
MPG MultipurposeGreasehavingaminimumdrippingpointof350
degreesF.Excellentwaterresistanceandadhesivequalities,
andbeingofextremepressuretype.(TimkenOK40pounds
minimum.)
EPGL ExtremePressureGearLube(oil)meetingAPIserviceclassifi-
cationGL-5orMIL-SpecMIL-L-2105.
EO Engine(crankcase)Oil.Gas-APISF/SGclass,MIL-L-2104.Die-
sel-APICC/CDclass,MIL-L-2104B/MIL-L-2104C.
HO HydraulicOil.APIserviceclassificationGL-3,e.g.Mobil424.

SECTION 1 - SPECIFICATIONS
3121801 1-3
1.6 CYLINDER SPECIFICATIONS
1.7 PRESSURE SETTINGS
1.8 LIMIT SWITCHES
The machine is equipped with the following limit switches:
Tilt Alarm - Illuminates a light on the platform and sounds an
alarm when the machine is 3° out of level side to side or 5° fore
and aft.
Platform Overload - When platform becomes overloaded, the
LED on the platform controller illuminates and the lift up and
drive functions are cut out. Platform is overloaded with 652 kg
(1437.5 lbs).
High Drive Cut-Out - High drive speed is cut out when the
platform is raised above the stowed position.
Max Drive Height - The drive function is cut out when the plat-
form is raised by 2.3 - 2.4 m (7.5 - 8 ft).
1.9 MAJOR COMPONENT WEIGHTS
1.10 CRITICAL STABILITY WEIGHTS
DO NOT REPLACE ITEMS CRITICAL TO STABILITY, SUCH AS ENGINES, AXLES OR
TIRES, WITH ITEMS OF DIFFERENT WEIGHT OR SPECIFICATION. DO NOT MOD-
IFY UNIT IN ANY WAY TO AFFECT STABILITY.
Table 1-10. Cylinder Specifications
Description Bore Stroke Rod Dia.
LiftCylinder 10.2cm
(4in.)
119.4cm
(47in.)
6.4cm
(2.5in.)
SteerCylinder 5.1cm
(2in.)
20cm
(7.84in.)
2.8cm
(1.12in.)
Table 1-11. Pressure Settings
MainRelief(±3.4bar/50psi) 227.5bar(3300psi)
SteerRelief-Left 158.8bar(2300psi)
SteerRelief-Right 117.2bar(1700psi)
LiftUpRelief 158.8bar(2300psi)
LevelingJackRelief 207bar(2500psi)
Table 1-12. Major Component Weights
Component Weight
Platform 295kg
(650lbs)
PlatformandExtension 454kg
(1000lbs)
ManualPlatformExtension 159kg
(350lbs)
ArmAssembly(IncludesLiftCylinder) 925kg
(2040lbs)
Chassis-w/StandardTires 1869kg
(4120lbs)
Table 1-13. Critical Stability Weights
Component Weight
TireandWheelAssembly-Std(each) 23kg
(50lbs)
Tire and Wheel Assembly - FF (each) 69 kg
(152lbs)
KubotaGas/DFEngine(Dry) 61.7kg
(136lbs)
KubotaDieselEngine(Dry) 42kg
(93lbs)

SECTION 1 - SPECIFICATIONS
1-4 3121801
1.11 SERIAL NUMBER LOCATIONS
For machine identification, a serial number plate is affixed to
the machine. The plate is located on the rear center of the
machine frame, just below the middle step of the ladder. In
addition, if the serial number plate is damaged or missing, the
machine serial number is stamped on the right front frame rail,
adjacent to the sizzor arms.
Figure 1-1. Serial Number Location

SECTION 1 - SPECIFICATIONS
3121801 1-5
Figure 1-2. Lubrication Diagram
Table 1-14. Lubrication Chart
INDEX NO COMPONENT NUMBER/TYPE LUBE POINTS LUBE METHOD INTERVAL
HOURS
1 HydraulicOilReservoir FillCap/DrainPlug HO-CheckHOLevel
HO-ChangeHO
10/500
2 HydraulicFilterElement N/A InitialChange-50Hours 250
3 EngineCrankcase,
EngineOilFilter,
EngineFuelFilter,
EngineFuelFilter(KubotaDF752)
FillCap/DrainPlug,
FilterElement,
FilterElement,
FilterElement
CheckEngineOilLevel,
InitialChange-50Hours,
Check&Cleanevery100hrs,
Check&Cleanevery100hrs
10/100,
200,
400,
Yearly
4 RailSlides N/A MPG-Brush 100
KEY TO LUBRICANTS:
MPG - Multi-purpose Grease
EPGL - Extreme Pressure Gear Lube
HO - Hydraulic Oil (Mobil 424)
TO AVOID PERSONAL INJURY, USE SAFETY PROP FOR ALL MAINTENANCE
REQUIRING PLATFORM TO BE ELEVATED.
NOTE: Be sure to lubricate like items on each side
Recommended lubricating intervals are based on
machine operations under normal conditions. For
machines used in multi-shift operations and/or exposed
to hostile environments or conditions, lubrication fre-
quencies must be increased accordingly.
NOTE: Operate hydraulic functions through one complete cycle
before checking hydraulic oil level in tank. Oil should be
visible in ADD sight window on hydraulic tank. If oil is not
visible, add oil until oil is visible in both ADD and FULL
sight windows on tank. Do not overfill tank.
Any time the pump coupling is removed, coat splines of
coupling with Texaco Code 1912 grease prior to assembly.

SECTION 1 - SPECIFICATIONS
1-6 3121801
4150548_E
Figure 1-3. Operating Temperature Specifications - Kubota

SECTION 1 - SPECIFICATIONS
3121801 1-7
1.12 TORQUE CHARTS
Figure 1-4. Torque Chart (SAE Fasteners - Sheet 1 of 5)
Torq ue
To r qu e Torq ue To r qu e Torque Torque

SECTION 1 - SPECIFICATIONS
1-8 3121801
Figure 1-5. Torque Chart (SAE Fasteners - Sheet 2 of 5))
Torq ue Tor que Torq ue
Torqu e To rqu e

SECTION 1 - SPECIFICATIONS
3121801 1-9
Figure 1-6. Torque Chart (SAE Fasteners - Sheet 3 of 5)
Clamp LoadTo r que
To r qu e
Torq ue Torque
Tor que
Torq ue

SECTION 1 - SPECIFICATIONS
1-10 3121801
Figure 1-7. Torque Chart (SAE Fasteners - Sheet 4 of 5)
To rqu e
To rqu e
Torque
To rq ue
To rqu e
To rq ue

SECTION 1 - SPECIFICATIONS
3121801 1-11
Figure 1-8. Torque Chart (METRIC Fasteners - Sheet 5 of 5)
Torq ue To rqu e Tor qu e To rqu e
To rqu e
To rq ue

SECTION 1 - SPECIFICATIONS
1-12 3121801
NOTES: