Jmaz Lighting HALO H6 WASH User manual

HALO H6 WASH
USER MANUAL
WWW.JMAZLIGHTING.COM

1. Thank you for choosing our Halo H6 Wash, for your own safety, please read this
user manual carefully before using.
No.
Item
Quan
tit
Unit
1 PAR Light 1 piece
2 Power cable with blue head 1 piece
3 User manual 1 piece
★For security reasons and in accordance with the terms, reassemble or modify the product is not allowed without
permission. Please note that due to human damage caused by improper use of the product, it will break the
warranty qualification. Moreover, the unprofessional operation may lead to short circuits, burns or electric shock,
and so on.
★This device has been full inspection before shipping. For your safety, please operate it according the User
Manual.
★If any damage caused by improper operation will result in the termination of the warranty claims. The
manufacturer does not accept any responsibility of property damage due to improper operation or personal injury
due to non-compliance with the operating instructions.
★Keep the manual in a safe place for future reference as well as after the product sale, lease, etc.
★Note: Based on product improvements, specification may change without notice. Changes in product
specifications related rights will be reserved.
2. Safety Instruction
1. When opening the packing, take all accessories out, and remove the light to a horizontal table for good
operation. First check whether the accessories are complete, then check carefully whether the whole light has no
damage. If there is any damage, please contact us as soon as possible.
2. AC Power: Check whether the local power supply is accordance with the
requirements of the product rated voltage.
3. The product is only suitable for indoor working environment. The light should
keep dry, keep away from wet, overheat or dusty environment. Don't come into contact with water and other
liquids to prevent or reduce the risk of electric shock or fire.
4. Please do not install the light directly on the surface of the combustible substance.
5. The people who install, operate and maintain of light professional certificate required.
6. When there are faults of the light, please stop using the light immediately. Don't try to repair, please contact the
nearest authorized technical assistance center, if the parts damage, always use the same type of parts replaced.
7. Don't touch any electrical wiring in the process of operation to prevent the risk of electric shock.
8. To make sure the light working environment temperature, the highest do not exceed 40℃, the lowest do not
exceed - 20 ℃.
9. Under the stable cooling working situation, the highest temperature of the housing of the light can reach 80 ℃,
please do not touch.
10. The light is design according to the type of electric shock protection. The light should be use in good
connection grounding power system and the earth sign port of the light should be connected to the installing
fixtures.

11. Do not use the damage of the insulating layer wire and also do not use the power cord overlap on the other
wire. When not in use or clean the light, please disconnect the power, don't pull the plug in hard or just drag the
wires.
12. There are no components inside for maintenance. Before start operation the light, please check whether all of
the shell is installed. In the case of the shell open used the light is prohibited.
Note: Before performing any installation, repair and cleaning of the lamp, please confirm that the
power cable has been cut off.
3. Product Specification
1. Voltage: AC100-240V 50-60Hz
2. Power Consumption: 250W
3. Light Source: 18 × 12W RGBAUV 6in1 LEDs
4. Beam Angle: 25° / 40°
5. Source life: 100,000 hours
6. Color: 1670 million kinds of colors
7. Working modes: Sound (Audio) Active, Show Mode, DMX, Master/ Slave.
8. Powercon: Input / Output
9. DMX Channel: 10 CH
10. W: 3.75KG
11.Size: 386*346*165mm
4. Display Main function
Interface
Function
Remark
D001
D001-D512
NO stands for no DMX signal, OK stands for receiving DMX
signal.
DMX NO
Press the confirmation key to determine (press 5 seconds to
enter the background, set various parameters)
TEMP
Temp of Light
Press 5 seconds to enter the background to set whether the
digital tube enters the sleep mode
Err’C
ClrNum
Color
Selection:001-006 1-6 Color Selection
6
R DIM
000-255 Red Dimming
0
G DIM
000-255 Green Dimming
0
B DIM
000-255 Blue Dimming
0
W DIM
000-255
White Dimming

5. Address Background Description
0
C DIM 000-255 Yellow Dimming
0
Y DIM
000-255 Purple Dimming
0
Strobe
000-100 Strobe from slow to fast
0
Program:00
00-16
Selection of Built-in 16 program
Speed
00-20
0 invalid
0
01-10:Jump changes,the higher the value, the faster the speed
11-
2:Gradual changes, the higher the value, the faster the
speed
Reset
ON-OFF
Restore factory value setting.
OFF
OFF is the default value. ON is valid, press the confirmation key
Interface Function Remark
Default
R DIM
000-255 Red Light Power upper limit selection
230
Max 230
G DIM
000-255 Green Light Power upper limit selection
70
Max 230
B DIM
000-255 Blue Light Power upper limit selection
85
Max 230
W DIM
000-255 White Light Power upper limit selection
85
Max 230
C DIM
000-255 Yellow Light Power upper limit selection
Max 230
Y DIM
000-255 Purple Light Power upper limit selection
Max 230
HighTemp
00—99
Upper limit of temperature protection power
（
99%
means 100%
）
70
Pwr 70%
HighTemp
ut45—ut80
Set the starting point of power reduction
temperature
60
At 60’c
Pwr Dowr
000-100
High temperature power down speed setting (fast
to slow)
30
Spd 030
Strobe
00-02
00:Strobe close
，
01-02
：
Two strobe modes
selction
1
1
Program ON- OFF Auto-run Mode Selection：OFF means closed
，
ON

6.Temperature Background (nixie tube display sleep enable) Description
Interface
Function
Remark
BckLight
ON-OFF
Whether to enable the nixie tube to display sleep
function (not used by default)
ON
7. LCD Display Function Instruction
8. DMX 512 Channel-10CH
Ch Function Value Description
1CH Master Dimmer
0
NO
001-255 Dark to Bright
2CH
R
0
NO
ON
ON means Open
MIC Set
ON- OFF
Voice control:
：
OFF means closed
，
ON means
Open
OFF
OFF
DimDilay
00-02 Represents two kinds of DimDilay
2
2

001-255 Dark to Bright
3CH G
0
NO
001-255 Dark to Bright
4CH B
0
NO
001-255 Dark to Bright
5CH W
0
NO
001-255 Dark to Bright
6CH C
0
NO
001-255 Dark to Bright
7CH Y
0
NO
001-255 Dark to Bright
8CH Strobe
0
NO
001-255 Slow to Fast
9CH Built-in Program
0
NO
001-255 16 color selection
10CH Built-in Speed
0 NO
001-255
0 invalid
1-127Jump changes,the higher the value,
the faster the speed
128-255 Gradual changes ,the higher the
value, the faster the speed

JMAZ LIGHTING
Technical Support
Phone: [phone]
E-mail: [e-mail]
Web: www.jmazlighting.com
Address: 2422 Lee Ave, South El Monte, CA 91733