JMQ A8 User manual

Manual for treadmill A8
Please read carefully before use this treadmill and keeping properly

1
1.DIRECTORIES
number
content
page
1
directories
1
2
grateful
2
3
Safe use instructions
2
4
Packing specifications
6
5
Assembly instructions
8
6
Electric control
instructions
12
7
Maintenance
instructions
19
8
Error removal
24
9
Repair terms
29
10
Exercise guidelines
30
11
Warm exercise
33

2
2、GRATEFUL
Thanks choose home use treadmill series A.
Our products will improve your health, the
more familiar with your treadmill, the
more easy and comfortable for use.So
please read this manual carefully before
use new treadmill.
To guarantee the maximum quality of
products, all parts of this treadmill use
high quality material, and pass strict
inspection and test. Refer to this
manual,can guide you assembly, use and
maintenance of this treadmill correctly.
Thanks for using！
3、SAFE USE INSTRUCTIONS
A、We consider many safety problems when design and
manufacture this treadmill, to ensure your safety,
please read all contents of this manual carefully

3
before use.We do not bear the consequences of any
abnormal operation.
RISK
B、Do not use the heart rate device together with
other wireless heart rate devices, or it can cause
electrical interference.
WARNING
Please follow the instructions below to avoid any hurt
to you or others.
1，To avoid any accidents or danger, please make sure
this treadmill is fully grounded before using.
2，While running, please clamp the safety lock(red) to
an appropriate position of your clothes, then when
in an emergency, you can pull of the safety lock
timely to stop the machine and make sure safe.
3，a、Please refer to your health care doctor’s opinion
before exercising.
b、Please wear comfortable sportswear when
exercising, don’t wear shoes with soft sole,
or shoe shavings will be involved into motor and

4
control system, and cause operating malfunction
c、Keep the room clean and tidy, avoid sundries being
electrostatically absorbed enter treadmill
interior, and cause operating malfunction.
d、User weight should not exceed 120kg.
4，This product is for one person use only when it is
running. To avoid any accidents, please do not let
children or pets play around to avoid accidents
5，Minimum spacing requirements for placing the
treadmill in the home after expand for use, means
distance from wall or furniture, no less than 100cm
respectively for front and both sides, no less than
200cm for rear, use 4 non-slip mat 10cm*10cm under
the parts of the treadmill which touch the ground.
6，Pleae do not use this treadmill if power line broken.
7，If the treadmill is damaged or broken, please do not
use and contact for repair.
8，Please do not touch any moving parts when the
treadmill is running, never press or stuff any
objects into the treadmill.
9，This machine is suitable for indoor use, please do
not use outdoors or in the gym.

5
10，Place the treadmill on clean and smooth floor, keep
good ventilation condition, ensure the unit
ventilated. Make sure there are no sharp objects
nearby. Do not use it near water or fire sources.
11，Please use the handrail when getting on or getting
off from the machine. Do not get off from the
treadmill when the walking machine is not stopped
completely.If need an emergency jump, you must pull
off the safety lock,then the treadmill will stop
immediately.
12，Do not use this machine when you are using oxygen
equipment or when spray is being used near it.
13，To make sure the treadmill running properly, please
do not install any accessories which are not
supplied by the original factory.
14，Must keep all parts of the treadmill installed
firmly.
15，Please turn off and unplug the power after using
the treadmill.
16，When not using the treadmill, please keep the
security lock safely to prevent any third parties
use it.

6
4. Packing List

7
A8 Single function screw pack
A8 Multifunction screws pack

8
5、Installation process
1：As shown in the figure below, the 2# transport
wheel set is fixed on the bottom pipe of the 1# main
frame with F# screw M8*45, I# M8 flat washer and H#
M8 lock nut.。

9
2：1. Rotate the armrest in the direction indicated
by the arrow in the figure above, and fix it on the
column tube of the main frame with G# screw M8*15,
I#M8 flat pad (screw fixing as shown below);
F
I
H
12

10
2. Rotate the electronic watch to the correct
position and lock it with the knob on the back;
3. Fix the column and frame with the E# knob and lock
it;
4. Fix the 3# side cover on the main frame with J#
screw M4*15.
The following steps are for the installation of
multi-function accessories
Step three:
1, the 6# massage bracket is fixed on the column with
G# screw M8*15 and I# flat pad M8, and then fixed
E
G
I
J3
3
1

11
with 7# massage stand with F# screw M8*45, I# flat
pad M8 and H# anti-loose nut M8 On the 6# massage
stand.
2, respectively, put the 11# sponge jacket on the
round tube of the 7# massage stand, and fix the 9#
dumbbell frame on the 7# massage stand with K# screw
M6*20.
3. Fix the 8# massage head on the flat plate at the
upper end of the 7# massage stand with its own screws,
flat pad and elastic pad, and finally put the 10#
dumbbell into the 9# dumbbell frame.
GI
GI
6
7
FIH
K
9
8
11
10

12
6,Electronic control operation

13
Boot start: Normal start after 3 seconds
countdown.
The number of programs is P1~P12 automatic
programs.
Safety lock function
Unplugging the safety lock immediately shows
that the "E7" treadmill is quickly stopped, and a
slamming alarm sounds. When the safety lock is
placed, the electronic watch is fully displayed for
2 seconds, and the data is all cleared.
Key Function
Start button, stop button:
“START ”is the start button. When the
treadmill is stopped, press the start button, the
speed displays “1.0”, and the treadmill starts.
The treadmill runs automatically for 60 minutes.
“STOP”is the stop button. When the treadmill
is running, press the stop button, all data is
cleared, the treadmill stops and returns to
manual mode, and the treadmill stops. These
two buttons are included on the handle.
Program key:

14
"PROGAM" is the program key. In the standby
state, press this button to cycle through the
manual mode to the automatic program P1 –
P12; the manual mode is the system default
operation mode, the default speed of the
manual mode is 1.0km/h, and the maximum
running speed is 12.8km/h.
Mode key:
“MODE”is the mode button. In the standby
mode, press this button to cycle through three
different countdown modes of operation from
time, distance and calories. H-1 is the time
countdown mode, H-2 is the distance
countdown mode, and H-3 is the calorie
countdown mode; when selecting various
modes, the speed increase/decrease key can be
used to set the relevant countdown value. When
you are done, press the “START”button to
start the treadmill.
Speed button:
“SPEED+”and “SPEED -”are speed addition
and subtraction keys: they can be used to adjust

15
the speed after the treadmill is started, stepping
0.1Km/time, “SPEED+”and “SPEED -”can
be used to parameterize the treadmill. To adjust
the set value.
Indication Function
Speed display
Displays the speed value of the current
run.
Time display
Shows the running time in manual mode or
the running time countdown in mode and
program.
Distance display
Displays the distance total in manual and
program mode or the inverse of the mode
running distance.
Calorie display
Shows the calorie accumulation during
exercise in manual and program mode or the
calorie count in mode run.

16
The range of data displayed by each
window:
TIME: 0:00 –60 (MIN)
DISTANCE: 0.00 –99 (KM)
CALORIES: 0.0 –990 (KC)
SPEED: 1.0 –12.8 (KM/H)
Automatic program
The default running time is
10 minutes. After the program is selected,
the running time is set. The program
segment of each program is divided into 10
segments, and the running time of each
program block is evenly distributed. The
motor stops the meter clear after the
running time is completed. The following
is a motion chart of 12 programs.
Time
Time set / 10 = Running time each stage

17
Phase
1
2
3
4
5
6
7
8
9
10
P1
SPEED
3
3
6
5
5
4
4
4
4
3
P2
SPEED
3
3
4
4
5
5
5
6
6
4
P3
SPEED
2
4
6
8
7
8
6
2
3
2
P4
SPEED
3
3
5
6
7
6
5
4
3
3
P5
SPEED
3
6
6
6
8
7
7
5
5
4
P6
SPEED
2
6
5
4
8
7
5
3
3
2
P7
SPEED
2
9
9
7
7
6
5
3
2
2
P8
SPEED
2
4
4
4
5
6
8
8
6
2
P9
SPEED
2
4
5
5
6
5
6
3
3
2
P10
SPEED
2
5
7
5
8
6
5
2
4
3
P11
SPEED
2
5
6
7
8
9
10
5
3
2
P12
SPEED
2
3
5
6
8
6
9
6
5
3
Parameter setting in 3 modes
The countdown time setting is initially
10:00 minutes, the setting range is
5:00---60:00 minutes, and the step is

18
1:00.
The calorie setting of the calorie count
is: 50 kcal, the setting range is 20---990
kcal, step 10.
The initial distance of the countdown
distance is 1.0 km, the setting range is
1.0---99.0 km, and the step is 1.0.
The cycle switching sequence is: manual,
time, distance, calories.
other
When a countdown parameter is run, the
display shows END, and a 0.5 second alarm
every 2 seconds until the treadmill stops,
stops the alarm, and then returns to the
manual mode state.
When setting a parameter, you can set the
loop. For example, the time setting range
is 5:00-30:00. When it is set to 99:00,
press the "+" button again. When you return
to 5:00, you can loop continuously. Add or
subtract the "+" and "-" symbols.
Countdown time, countdown calorie, and

19
countdown distance can only be set to one
of them. Run the last setting, the set
parameters are counted down, and the other
displays positive count.
The standard value for calories is 30
kcal/km.
Bluetooth sharing music (optional
feature)
Turn on the treadmill
power switch, manually search for the
Bluetooth device (JF-BTMP3) with the
mobile phone, find the Bluetooth device to
click and connect. After the connection is
successful, the music on the mobile phone
can be transmitted to the power amplifier
device on the treadmill through Bluetooth,
and operated on the computer. Lower tone,
volume addition and subtraction, etc.
7, maintenance guide