JMS Daytona Sensors Smart Spark Super Speedway Trans Am TA2... User manual

1.
INSTALLATION GUIDE
WHAT'S IN THE BOX
CAUTION: This system is designed for racing and it has
approved for by the Trans Am Racing Series TA2 racing class.
Carefully read instructions before proceeding. Not legal for sale
or use in California or on any pollution controlled vehicles.
OVERVIEW
• Supports Approved TA2 GM LS Racing Engines
(Carbureted LS Engines With 58 Tooth Crank Trigger)
• Preprogrammed with Approved TA2 Ignition Timing
Advance Tables
• Unit is Sealed for the TA2 Racing Series
• Status LEDs - Display Device and Trigger Input Status
• Fully Encapsulated Construction
• Heavy Duty 12 Pin Deutsch Connectors used for
Signal Connections
• Designed & Assembled in the USA
Smart Spark TA2 Super Speedway (P/N TA2SSLS-K) was
specically designed for the Trans Am TA2 racing series. It is a
complete plug n’ play racing ignition system that is designed to
be used on LS based TA2 racing engines. This fully encapsulated
device is preprogrammed with approved TA2 ignition timing
advance tables. The TA2 Super Speedway version of our Daytona
Sensors Smart Spark ignition system has been designed to meet
specic Trans Am TA2 racing requirements.
STEPS 1—4
1. Mount the TA2 module in a convenient location. For hookup,
refer to the gure 3 diagram and the appropriate wire overview
at the end of the instructions.
2. Connect the ground terminal (black and black/white wires) to a
suitable engine or chassis ground.
3. Connect +12V power (pink wire) to the ignition switch. This
circuit should be protected with a 20 amp ATC fuse.
4. Connect the tach signal (white wire) as shown in the basic
hookup on next page.
1. Smart Spark TA2 SS Controller
(P/N TA2SSLS-B)
2. Smart Spark TA2 SS Harness
(P/N TA2SSLS-H)
2.

FIGURE 3- BASIC HOOKUP
+12V
IGNITION
SWITCH +12V PWR PINK (PL2 PIN 6)
TACH WHITE (PL2 PIN 11)
PL1 PL2
RPM
TACH
CHASSIS GROUND BLACK (PL2 Pin 7)

JMS–Daytona Sensors warrants to the original purchaser:
Your product will be free from defects in materials & workmanship
for a period of twelve (12) months from the original purchase
date. The warranty only covers the product itself & not the cost
of removal & re-installation of the product. We may extend
the limited warranty on a case by case basis, based on the
circumstances of the warranty claim. Our products are designed
exclusively for use in racing applications. JMS–Daytona Sensors
products that are not installed according to the supplied
instructions, may not be covered by warranty.
Specic conditions that will VOID the product warranty:
• If the product case has been opened or the product has
been modied or repaired.
• If the product was not installed or used correctly.
• If the product has been tampered with by: negligence,
misuse or accident.
• If the product is returned without explanation of the
problem or Return Authorization.
Contact us at 601-766-9424 for a Return Authorization Number:
All warranty returns should be returned freight pre-paid &
should include inside of the box: Proof of Purchase & a Letter
that contains both the Return Authorization Number and a Clear
Explanation of the EXACT problem.
The Return Authorization Number should also be clearly written
on the outside of the box.
Send all returns to:
JMS Returns
240 Springview Commerce Drive, Bld 1, Ste J
DeBary, FL 32713
This product was designed for RACING. JMS–Daytona Sensors is
not liable for any and all consequential damages arising from the
breach of any implied or written warranty in regards to the sale of
this product, in excess of the purchase price.
Technical Support & Contact Information:
JMS–Daytona Sensors
240 Springview Commerce Drive, Bld 1, Ste J
DeBary, FL 32713
601-766-9424 or 386-304-0700
Technical Support Hours:
Monday - Friday 9:00am - 5:00pm (Central Standard Time)
Installation videos available online: www.youtube.com/jmschip
If you have any questions, please contact JMS technical support
via email: [email protected]
Follow Us on Social Media
For a chance to be featured, tag your posts with: #SmartSparkSS
Warranty & Contact Information
WIRING OVERVIEW
BLACK 12 PIN DEUTSCH CONNECTOR SIGNALS
PIN SIGNAL DESCRIPTION
1Coil Drive 1 Coil 1 drive signal
2Coil Drive 2 Coil 2 drive signal
3Coil Drive 3 Coil 3 drive signal
4Coil Drive 4 Coil 4 drive signal
5Coil Drive 5 Coil 5 drive signal
6+12V Power Switched +12V power
7Ground Connects to engine or chassis ground
8Coil Drive 6 Coil 6 drive signal
9Coil Drive 7 Coil 7 drive signal
10 Coil Drive 8 Coil 8 drive signal
11 Tach Connects to tachometer
(standard 12V square wave signal)
Facebook: @jmschips / @daytonasensors
Instagram: @jmschip
YouTube: www.youtube.com/jmschip
WIRING OVERVIEW
GRAY 12 PIN DEUTSCH CONNECTOR SIGNALS
PIN SIGNAL DESCRIPTION
1CKP Crankshaft position sensor signal input
2 CMP Camshaft position sensor signal input