JONARD TOOLS FCCN-125 User manual

FCCN-125 & FCCN-250
FERRULE END-FACE CLEANER INSTRUCTION MANUAL
IMPORTANT - HOW TO REALIGN THE CLEANING CLOTH
Stopper
Full Empty
CAUTION ANGLE NOTICE
Misalign
Realign
Cleaning cloth
Misalign Withdraw
Push the stopper
backward
Pull the stopper forward
ATTENTION
DANGER
WARNING
Please hold the base of the cleaning guide when you tilt the tip upwards. FCCN-250 can be tilted
on an angle of 15,30 or 45 degrees. FCCN-125 can be tilted on an angle of 15 or 30 degrees. Do
not tilt cleaning guide down: ONLY TILT UPWARDS. When you feel the click button does not move
smoothly, please check the indicator window (cleaning cloth may be empty).
Jonard Tools assumes no liability whatsoever for actions by a third party, other accidents, intentional
or accidental misuse, or use under other abnormal conditions by the user.
• Do not use or leave in places exposed to high temperatures or in places where flammable
gases are generated.
• Do not peer through the ferrule end-face and adapters.
• Do not use with live fiber.
• Do not subject to strong impact by dropping or throwing this.
• Do not disassemble, make repairs or modify.
• Do not splash with water or other liquids.
• Should this become splashed with liquid, immediately stop cleaning.
• Malfunctions caused by splashing or moisture are outside the scope of the warranty and
cannot be repaired.

FCCN-250
1. Open tip cover.
2. Insert your ferrule or connector into
ferrule guide until ferrule or connector
housing contacts the face of the
protection cap.
3. Maintain pressure on the ferrule or
connector. Depress and release the
button one time. Note: for extremely
dirty connectors, two button pushes
may be necessary.
4. Remove your ferrule or connector
from the ferrule guide and close the
tip cover of the protection cap.
FCCN-250
1. Remove protection cap.
2. Insert cleaning tip into adapter.
3. Push in until stopper of cleaning guide
comes in contact with the adapter.
Maintain pressure to realize spring
pressure inside adapter.
FCCN-125
1. Remove protection cap.
2. Insert cleaning tip into adapter.
3. Push in until stopper of cleaning guide
comes in contact with the adapter.
Maintain pressure to realize spring
pressure inside adapter.
FCCN-125
1. Open tip cover.
2. Insert your ferrule or connector into
ferrule guide until ferrule or connector
housing contacts the face of the
protection cap.
3. Maintain pressure on the ferrule or
connector. Depress and release the
button one time. Note: for extremely
dirty connectors, two button pushes
may be necessary.
4. Remove your ferrule or connector
from the ferrule guide and close the
tip cover of the protection cap.
FEATURES
• Adjustable angled head (up to 45°) is perfect for getting into hard-to-reach places
• Flip-open cap makes it easy to insert connectors for cleaning
• Remove cap to clean fiber in bulkhead adapters
• Static-free cloth provides up to 350 swipes per cleaner
• Perfect for cleaning any LC, MU, FC, SC or ST connector
PART DESCRIPTION
OPERATING INSTRUCTIONS - CLEANING THROUGH ADAPTER
OPERATING INSTRUCTIONS - CLEANING CABLE CONNECTORS
FCCN-250 FCCN-125
Before insertion After insertion
Prohibited
Inserts straight
Prohibited Inserts straight Prohibited Inserts straight
Before insertion After insertion
Prohibited
Inserts straight
4. Depress and release the click button
one time. Note: for extremely dirty
connectors, two click button pushes
may be necessary.
5. Remove ferrule mate from adapter and
replace protection cap before storage.
4. Depress and release the click button
one time. Note: for extremely dirty
connectors, two click button pushes
may be necessary.
5. Remove ferrule mate from adapter and
replace protection cap before storage.