JONATHAN Y JYL7604A User manual

PIECE DESCRIPTION PICTURE
QUANTITY
PIECE DESCRIPTION PICTURE QUANTITY
A Mounting
Bracket 1X I bulb 1X
B mounting screw 2X J glass shade 1X
C Base 1X K Frame 1X
D washer 2X L tube 1X
E
screws
2X M Cap Nut 1X
F wire connector 3X N washers 2X
G ground screw 1X O studs 2X
H socket 1X P
top hood
1X
Model#: JYL7604A
Product Dimensions: 10.5''L X 8.875"WX 15"H
* Please make sure that you have all parts indicated before you begin assembly of this item
* This item should be assembled on a soft surface to prevent scratching the finish during assembly
* To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and
installation
*The external flexible cable or cord of this lamp cannot be replaced
If the cord is damaged, the lamp shall be destroyed
Part List and Hardware List
WARNING
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT
BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR
OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
CARE AND MAINTENANCE
To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the
surface of the fixture.
To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at
the fuse box. Next, use a dry or slighly damperned clean clorth (use clean water, never a solvent) to wipe the interior surface of
the fixture.
Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
NOTICE& IMPORTANT SAFETY INSTRUCTIONS

2. Fix the mounting bracket(A) to the outlet box with mounting screw(B).
3. Loose the studs(O) to remove from the Frame(K) .
4. Loose the Cap Nuts(M) and washer(N) to remove from the Frame(K) .
5. Fix the glass(J) to the tube(L) by using Cap Nuts(M) and washer(N)
6. Insert the bulb (I) into the socket (H).
7. Fix the Frame(K)) to the top hood (P)by Using 2pcs studs(O) .
8. Make wire connections, with wire connectors(F), following the reference chart listed below.
*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped
and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
Grounding Instructions:
a) For installation in the United States: Wrap ground wire from outlet box around green
ground screw(G) on mounting bracket, no less than 2" from wire end. Tighten ground screw. If
fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector.
b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire
around green grounding screw on mounting bracket. Tighten ground screw.
9. Fix the base(C) to the Mounting bracket(A) by Using 2pcs screws(E) and washer(D) .
PLEASE USE TYPE"A" BULB MAX 25-WATT OR CFL BULB MAX
9-WATT OR LED BULB MAX 5-WATT
THERE IS 1PC 4 WATT LED BULB IN THE BOX
ENJOY YOUR LAMP
* Parallel Cord (round & smooth) * Parallel Cord (square & ridged)
Clear, Brown, Gold or Black without Tracer (colored stripes) Clear, Brown, Gold or Black with Tracer (colored stripes)
Insulated Wire (not green) with copper metal conductor Insulated Wire (not green) with Silver metal conductor.
Connect, Hot, Black or Red Outlet Supply Wire to: Connect, Neutral, White Outlet Supply Wire to:
Black White
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and
hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 20 minutes.
1. Loose The Screws(E) to Remove the Mounting bracket(A) from the base(C).