JTL VM3010A User manual

Quick Start Guide
VM3010A
P/N 102221-0
Mounting
Mounts with the following hole patterns can be used on the VM3010A: AMPS,
VESA 75 or VESA 100. Use M5 (12mm) screws. Usage of thread locking products
like Loctite® is recommended.
Example of mounting with RAM mounts
For information about additional accessories, please contact your
JLT sales representative.
jltmobile.com
For further support or guidance, visit:
jltmobile.com/support

First startup
To start the unit, press and hold power button for 3 seconds. On first startup of a JLT
unit with a JLT OS image preloaded, Android setup will start. Do not shut down the
unit until the setup is completed, otherwise the image may be corrupt. If the system
already has been corrupted, a disk restore can be made from a JLT OS image,
contact your local JLT sales representative for more information.
Note: If your unit is provided with a specific customer image, this step may be skipped.
Touch screen, PCT option
The VM3010A is equipped with a Projected Capacitive Touch screen, also called
PCT or PCAP. The touch screen is calibrated from factory and needs no further
calibration. It’s normally operated with fingers and may also be used with purpose-
designed stylus for PCT or PCAP. A stylus designed for resistive touch screens will
not work.
Installing SIM-card and Micro SD-card
The VM3010A supports data connection using 4G LTE SIM-cards**
and fits up to two Micro-SIM cards.
INSTRUCTIONS
1. Remove the service window by unscrewing the two screws
2. Remove the screws and carefully lift the cover
3. Locate the appropriate card slot (see the picture below) and insert the card.
SIM-card should be inserted with the IC contact patch side facing towards the front
side of the unit (as shown in the picture below)
Micro SD-card should be inserted with the label side facing towards the back of the
unit (as shown in the picture below)
**4G LTE support is an optional feature
***Heater is optional
LED indicators
LEFT SIDE INDICATORS
(from the top)
1. Wi-Fi
2. Bluetooth
3. UPS battery
RIGHT SIDE INDICATORS
(from the top)
1. Light sensor (no function)
2. Blanking
3. Heater*** default no function
Key Function
F1 + F2 Touch keypad lock/ unlock
F2 + F3 Lamp on/off
F3 + F4 Volume adjustment
F4 + F5 Brightness adjustment
F5, long press Camera
Fn, followed by F6 - F10 Function key form F6 - F10
Power input
Input 10V-60V with power isolation and ignition control
Fuse specification: 2x 15A, 250 volt, UDA type
POWER CABLE DESCRIPTION
Red VCC+
Black VCC-
Green Ground
White Ignition input****
Without Ignition Function
With Ignition Function
Buttons
NOTE
As the surface is made of glass it will withstand most common substances, but DO
NOT use fluids like bleach or any strong alkali cleaning agents such as Sodium or
Potassium hydroxide for cleaning as it may etch the glass and leave persistent gray
patterns on the surface.
Docking and undocking
INSTRUCTIONS
1. Align the golden connector and guide pin holes on the unit with the golden
connector and guide pins on the docking station
2. Insert the device into the guide pin holes on the docking station
3. Slightly push the upper part of the unit towards the docking station until
you hear a “click” sound, indicating the unit is fixed on the docking station
To undock the unit, push the release latch on top of the docking station
and lift the unit
DIGITAL MICROPHONEDIGITAL MICROPHONE
POWER BUTTON/
POWER INDICATOR
LED INDICATORLED INDICATOR
SPEAKERS
FUNCTION BUTTONS
COM1 AND COM2
USB 2.0 X2)
CAN BUS / AUDIO
SERVICE WINDOW*
LAN PORT
*Notice: Service window covers SD Card Slot/ sim card slot, USB
Type-C and DC in power input jack
WI-FI ANTENNA CONNECTOR
GPS ANTENNA CONNECTOR
WWAN ANTENNA CONNECTOR
WIDE RANGE POWER INPUT
1. 2. 3.
Components and interfaces
****The ignition cable (White) must be connected
to the battery positive (via the fuse) if the customer
does not want to have ignition function.