Juniper ACX2200 User manual

ACX2200 Universal Metro Routers
Quick Start
April 2016
Part Number: 530-062854
Revision 01
This document describes how to install the Juniper Networks®ACX2200 Universal Metro Router.
Contents ACX2200 Quick Start Description | 3
Step 1: Prepare the Site for Installation | 5
Step 2: Install the Router | 7
Tools Required to Install the Router in a Rack | 7
Install the Mounting Brackets | 7
Install the ACX2200 Router in the Rack | 8
Step 3: Ground the ACX2200 Router | 10
Tools Required to Ground the ACX Router | 10
Connect the Grounding Cable | 10
Step 4: Connect External Devices and Cables | 12
Tools Required to Connect External Devices and Cables | 12
Connect the ACX2200 Router to a Network for Out-of-Band Management | 13
Connect the ACX2200 Router to a Management Console or Auxiliary Device | 13
Connect Network Interface Cables to the ACX2200 Router | 13
Step 5: Connect Power to the ACX2200 Router | 15
Connect AC Power to an AC-Powered ACX2200 Series Router | 15
Connect DC Power to a DC-Powered ACX2200 Router | 16
Step 6: Perform Initial Software Configuration | 19
Enter Configuration Mode | 19
Configure User Accounts and Passwords | 20
Configure System Attributes | 20
1

Commit the Configuration | 21
Safety Warnings | 23
Compliance Statements for NEBS | 24
Compliance Statements for EMC Requirements for the ACX2200 Router | 25
Canada | 25
European Community | 25
Junos OS Documentation and Release Notes | 26
Requesting Technical Support | 26
Self-Help Online Tools and Resources | 26
Creating a Service Request with JTAC | 27
Revision History | 27
2

ACX2200 Quick Start Description
This Quick Start contains information you need to install and configure the router quickly. For complete
installation instructions, see the ACX2200 Universal Metro Routers Hardware Guide.
WARNING: This Quick Start contains a summary of safety warnings in “Safety
Warnings” on page 23. For a complete list of warnings for this router, including
translations, see the ACX2200 Universal Metro Routers Hardware Guide.
The ACX Universal Metro Routers are Ethernet-optimized mobile backhaul routers that provide both
switching and carrier-class Ethernet routing. The ACX Series routers enable a wide range of business and
residential applications and services, including microwave cell site aggregation, MSO mobile backhaul
service cell site deployment, and service provider or operator cell site deployment. The ACX2200 routers
have high-density Ethernet interfaces and high-capacity switching throughput.
The routers are single-board routers with a built-in Routing Engine and one Packet Forwarding Engine.
The Packet Forwarding Engine has one “pseudo” Flexible PIC Concentrator (FPC 0). Because there is no
switching fabric, the single Packet Forwarding Engine takes care of packet forwarding.
The compact routers are one rack unit (U; that is, 1.75 in., or 4.45 cm) tall. Several routers can be stacked
in a single floor-to-ceiling rack for increased port density per unit of floor space.
The ACX2200 routers contain four Gigabit Ethernet RJ-45 ports, four Gigabit Ethernet combination ports
(either four Gigabit Ethernet RJ-45 ports or four Gigabit Ethernet SFP ports), two Gigabit Ethernet SFP
ports, and two 10-Gigabit Ethernet SFP+ ports. Use only one set of these combination ports (labeled
COMBO PORTS) at a time.
Figure 1 on page 4 and Figure 2 on page 4 shows the front panel of the ACX2200 router.
3

Figure 1: Front Panel of the DC-powered ACX2200 Router
g017848
ACX2200
15
MGMT CONSOLE/AUX
SYS 0 1 EXT REF CLK IN
ALARM
OUTIN IN OUT
1PPS 10MHz
0/0/0
0/0/2
0/0/1 0/1/10/1/0
0/0/3 0/1/2
GE
0/1/3
COMBO PORTS XE
0/3/0 0/3/1GE
0/1/2 0/1/3 0/2/1
0/1/0 0/1/1 0/2/0
9
7
8
6
10
4
1114
1 2
13 12
3 5
9—1—Gigabit Ethernet SFP portsDC terminal
10—2—Combination Gigabit Ethernet SFP portsManagement Ethernet port
11—3—External clocking portsConsole or auxiliary port
12—4—External clocking input portAlarm contact port
13—5—USB portsRJ-45 Gigabit Ethernet network ports
14—6—System LEDCombination Gigabit Ethernet ports
15—7—Grounding terminalESD point
8—Ten-Gigabit Ethernet SFP+ ports
Figure 2: Front Panel of the AC-powered ACX2200 Router
g017875
ACX2200
MGMT CONSOLE/AUX
SYS 0 1 EXT REF CLK IN
ALARM
OUTIN IN OUT
1PPS 10MHz
0/0/0
0/0/2
0/0/1 0/1/10/1/0
0/0/3 0/1/2
GE
0/1/3
COMBO PORTS XE
0/3/0 0/3/1GE
0/1/2 0/1/3 0/2/1
0/1/0 0/1/1 0/2/0
9
7
8
6
10
4
1114
1 2
13 12
3 5
8—1—Ten-Gigabit Ethernet SFP+ portsAC inlets
9—2—Gigabit Ethernet SFP portsManagement Ethernet port
10—3—Combination Gigabit Ethernet SFP portsConsole or auxiliary port
11—4—External clocking portsAlarm contact port
12—5—External clocking input portRJ-45 Gigabit Ethernet network ports
13—6—USB portsCombination Gigabit Ethernet ports
14—7—System LEDESD point
4

Step 1: Prepare the Site for Installation
Prepare your site for installation by observing the following guidelines:
•You can install the router in a four-post rack or cabinet or an open-frame rack.
•The rack rails must be spaced widely enough to accommodate the chassis's external dimensions: 1.7 in.
(4.4 cm) high, 9.4 in. (24 cm) deep, and 17.5 in. (44 cm) wide. The outer edges of the mounting brackets
extend the width to 19.2 in. (48.7 cm).
•One person must be available to lift the router while another secures the router to the rack.
•The rack must be strong enough to support the weight of the fully configured router, up to 7 lb (3.2 kg).
•For service personnel to remove and install hardware components, allow at least 2.16 in. (5.5 cm) in
front of the router.
•The rack or cabinet must have an adequate supply of cooling air.
•Ensure that the cabinet allows the chassis hot exhaust air to exit from the cabinet without recirculating
into the router.
•When deploying the router in environments where the router may operate between 131° F (55° C) and
149° F (65° C), allow a 1 rack unit (U) gap above and below the router.
•When installing the router in a cabinet, ensure that the bottom of the cabinet is closed and there is no
opening.
•You must install the router into a rack that is secured to the building structure.
•Mount the router at the bottom of the rack if it is the only unit in the rack.
•When mounting the router in a partially filled rack, load the rack from the bottom to the top, with the
heaviest component at the bottom of the rack.
•Install the router only in restricted areas, such as dedicated equipment rooms and equipment closets, in
accordance with Articles 110-16, 110-17, and 110-18 of the National Electrical Code, ANSI/NFPA 70.
5

Figure 3: ACX Series Routers Rack Clearance and Chassis Dimensions
RearFront 17.5"
(44.5 cm)
9.4"
(24 cm)
g006404
Front-mounting flange
19.2"
(48.7 cm)
2.16" (5.5 cm)
clearance required
for the cables
.75" (2 cm)
clearance required
for free airflow
3" (7.6 cm)
3" (7.6 cm)
6

Step 2: Install the Router
IN THIS SECTION
Tools Required to Install the Router in a Rack | 7
Install the Mounting Brackets | 7
Install the ACX2200 Router in the Rack | 8
Tools Required to Install the Router in a Rack
To install the router in a rack, you need the following tools:
•Phillips (+) screwdriver, number 2
•ESD grounding wrist strap
Install the Mounting Brackets
Two mounting brackets for front or rear mounting ship with the router (see Figure 4 on page 8 and
Figure 5 on page 8).
Attach both mounting brackets to either the front or rear of the chassis:
1. Align the bracket with the two sets of mounting holes.
2. Insert the four screws at the top and bottom of the bracket and tighten each partially.
3. Tighten the four screws completely.
4. Repeat the procedure for the other bracket.
7

Figure 4: Installing the Mounting Brackets to the Front of the ACX2200 Router
g006405
Figure 5: Installing the Mounting Brackets to the Rear of the ACX2200 Router
g006406
Install the ACX2200 Router in the Rack
The router can be installed horizontally in a rack or cabinet.
NOTE: For additional installation options, contact JTAC.
One person must be available to lift the router while another secures the router to the rack. The chassis
weighs approximately 7 lb (3.2 kg). To install the chassis (see Figure 6 on page 9):
1. Ensure that the rack is in its permanent location and is secured to the building. Ensure that the installation
site allows adequate clearance for both airflow and maintenance.
2. Position the router in front of the rack or cabinet.
3. Have one person grasp both sides of the router, lift the router, and position it in the rack, aligning the
mounting bracket holes with the threaded holes in the rack rails. Make sure the chassis is level.
8

4. Have the second person install a mounting screw into each of the open mounting holes aligned with
the rack, starting from the bottom.
5. Visually inspect the alignment of the router. If the router is installed properly in the rack, all the mounting
screws on one side of the rack should be aligned with the mounting screws on the opposite side, and
the router should be level.
Figure 6: Installing the Front-Mounted Router in the Rack
g006407
Mounting rack
Mounting bracket
9

Step 3: Ground the ACX2200 Router
IN THIS SECTION
Tools Required to Ground the ACX Router | 10
Connect the Grounding Cable | 10
You must ground DC-powered routers before connecting DC power.
Tools Required to Ground the ACX Router
To ground the router, you need the following tools:
•Phillips (+) screwdriver, number 2
•ESD grounding wrist strap
•Two SAE 10-32 screws and flat washers (not provided)
•Grounding lug, Panduit LCD6-14BH-L or equivalent (not provided)
•Grounding cable, use 16-AWG (1.31 mm2) 90° C wire for AC systems (not provided)
Connect the Grounding Cable
You ground the router by connecting a grounding cable to earth ground and then attaching it to the chassis
grounding points. To ground the router:
1. Verify that a licensed electrician has attached the cable lug, which is provided with the router, to the
grounding cable.
2. Attach an ESD grounding strap to your bare wrist, and connect the other end of the strap to an approved
site ESD grounding point. See the instructions for your site.
3. Ensure that all grounding surfaces are clean and brought to a bright finish before you make grounding
connections.
10