Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - E120 AND E320 MODULE GUIDE REV... User manual

E Series™ Broadband
Services Routers
E120 and E320 Module Guide
Release
11.3.x
Published: 2010-10-01
Copyright © 2010, Juniper Networks, Inc.

This guide provides an overview and description of the line modules (LMs), switch route
processor (SRP) modules, switch fabric modules (SFMs), and input/output adapters
(IOAs) available for the Juniper Networks E120 and E320 Broadband Services Routers.
NOTE: A release may support multiple versions of a module or IOA. For
information, see Software Compatibility in JunosE System Basics Configuration
Guide, Chapter 6, Managing Modules.
Table 1 on page 3 lists the modules and IOAs supported by the router.
This guide also contains the following appendixes:
•IOA Protocol Support on page 49
•Module and Slot Combinations on page 73
•Module Name Cross-Reference Information on page 77
•Product Reclamation and Recycling Program on page 79
For more information about E120 routers, E320 routers, modules, and IOAs, refer to the
following guides:
•Modules that have reached end-of-life—E Series End-of-Life Module Guide
•Module installation and maintenance—E120 and E320 Hardware Guide
•Managing routers—JunosE System Basics Configuration Guide
•Configuring modules—JunosE Link Layer Configuration Guide
Copyright © 2010, Juniper Networks, Inc.2
E120 and E320 11.3.x Module Guide

Table 1: Modules and IOAs
PageFirst JunosE SupportModule LabelModule/IOA Type
Line Module
57.0.1ES2
4G
LM
LM-4
77.2.0ES2
10G
UPLINK
LM
LM-10 Uplink
98.0.0ES2
10G LM
LM-10
1110.1.0ES2
10G ADV LM
LM-10 ADV
SRP Module
127.0.1SRP-100SRP-100
148.2.0SRP-120SRP-120
167.3.0SRP-320SRP-320
SFM Module
187.0.1SFM-100SFM-100
198.2.0SFM-120SFM-120
207.3.0SFM-320SFM-320
Gigabit Ethernet IOA
217.0.1ES2-S1
GE-4
IOA
GE-4 IOA
257.2.0ES2-S1
GE-8
IOA
GE-8 IOA
299.0.0ES2-S3
GE-20
IOA
GE-20 IOA
337.2.0ES2-S2
10GE PR
IOA
10GE PR IOA
OC3/STM1 ATM IOA
3Copyright © 2010, Juniper Networks, Inc.

Table 1: Modules and IOAs (continued)
PageFirst JunosE SupportModule LabelModule/IOA Type
377.0.1ES2-S1
OC3-8
STM1
ATM IOA
OC3/STM1-8 ATM IOA
OC12/STM4 ATM IOA
397.0.1ES2-S1
OC12-2
STM4
ATM IOA
OC12/STM4-2 ATM IOA
OC12/STM4 POS IOA
417.0.1ES2-S1
OC12-2
STM4
POS IOA
OC12/STM4-2 POS IOA
OC48/STM16 IOA
437.0.1ES2-S1
OC48
STM16
POS IOA
OC48/STM16 POS IOA
Redundancy IOA
457.0.1ES2-S1
REDUND
IOA
REDUND IOA
Service IOA
467.0.1ES2-S1
SERVICE
IOA
SERVICE IOA
SRP IOA
477.0.1SRP IOASRP IOA
Copyright © 2010, Juniper Networks, Inc.4
E120 and E320 11.3.x Module Guide

LM-4 Line Module
ES2 4G LM
Module label
•Not applicable
Number of ports
•First supported: 7.0.1
Software release
•176 W maximum
•Acts as frame forwarding engines for the physical interfaces
•Responsible for processing data traffic
•Pairs with IOAs to process data from different types of network connections
Description
•FFA ASIC
Type
•Supports a line rate of 128–byte packets on IOAs
•The 100–Gbps switch fabric allocates 3.4 Gbps of overall bandwidth to each regular
line module slot and 10 Gbps of overall bandwidth to each of the turbo slots (slot
2 and slot 4).
•The 320–Gbps switch fabric allocates 10 Gbps of overall bandwidth to each line
module slot. The line interface on the ES2 4G LM when installed in a 320 Gbps
fabric configuration is 3.9 Gbps; you can achieve this rate with random packet sizes
in the range 64–1518 bytes or a mixture of packet sizes that represent Internet mix
traffic (IMIX).
•See JunosE System Basics Configuration Guide, Chapter 6, Managing Modules for
more information.
Capability
•Not applicable
Software features
•E320 router
•E120 router
Model compatibility
•Not applicable
Line module compatibility
•SRP-100
•SRP-120
•SRP-320
SRP module compatibility
•Yes (Redundancy IOA must be installed in either slot 0 or slot 11)
•Can only back up another ES2 4G LM
Line module redundancy
compatibility
•Not applicable
Port redundancy support
•Not applicable
Cables and connectors
When lit, LED indicates:
•OK (green)—Self-test passed
•FAIL (red)—Failure detected
•ONLINE (green)—Online with no alarms or errors
•REDUN (green)—Redundant card available
LEDs
5Copyright © 2010, Juniper Networks, Inc.
LM-4 Line Module

•See Monitoring Modules in JunosE System Basics Configuration Guide, Chapter 6,
Managing Modules.
Alarms, errors, and events
Copyright © 2010, Juniper Networks, Inc.6
E120 and E320 11.3.x Module Guide

LM-10 Uplink Line Module
ES2 10G UPLINK LM
Module label
•Not applicable
Number of ports
•First supported: 7.2.0
Software release
•150 W maximum
•Acts as frame forwarding engines for the physical interfaces
•Processes up to 10 Gb of data traffic
•Pairs with ES2–S2 10GE PR IOA only
•In a SRP-100 configuration, it must be installed in a turbo slot only (slot 2 or slot 4)
•If you install the line module in a slot other than slot 2 or slot 4, it will be disabled
•If you install a LM-10 Uplink module next to a configured line module that is already
installed in slot 3 or slot 5, the LM-10 Uplink module will be disabled
•If you install a line module in slot 3 or slot 5 next to a previously installed LM-10
Uplink module, the non-LM-10 Uplink module will be disabled
•In a SRP-120 and SRP-320 configuration, it can be installed in any slot
Description
•IXP network processor
Type
•Supports a line rate of 128–byte frames on IOAs
•The 100–Gbps switch fabric allocates 3.4 Gbps of overall bandwidth to each regular
line module slot and 10 Gbps of overall bandwidth to each of the turbo slots (slot 2
and slot 4).
•The 120–Gbps and 320–Gbps switch fabrics allocate 10 Gbps of overall bandwidth
to each line module slot.
•See JunosE System Basics Configuration Guide, Chapter 6, Managing Modules for more
information.
Capability
•Not applicable
Software features
•E320 router
•E120 router
Model compatibility
•Not applicable
Line module compatibility
•SRP-100
•SRP-120
•SRP-320
SRP module compatibility
•Yes (Redundancy IOA must be installed in either slot 0 or slot 11)
•Can only back up another ES2 10G UPLINK LM
Line module redundancy
compatibility
•Not applicable
Port redundancy support
•Not applicable
Cables and connectors
7Copyright © 2010, Juniper Networks, Inc.
LM-10 Uplink Line Module

When lit, LED indicates:
•OK (green)—Self-test passed
•FAIL (red)—Failure detected
•ONLINE (green)—Online with no alarms or errors
•REDUN (green)—Redundant card available
LEDs
•See Monitoring Modules in JunosE System Basics Configuration Guide, Chapter 6,
Managing Modules.
Alarms, errors, and events
Copyright © 2010, Juniper Networks, Inc.8
E120 and E320 11.3.x Module Guide

LM-10 Line Module
ES2 10G LM
Module label
•Not applicable
Number of ports
•First supported: 8.0.0
Software release
•198 W maximum
•Acts as frame forwarding engines for the physical interfaces
•Processes up to 10 Gb of data traffic
•Pairs with ES2–S2 10GE PR IOA and ES2–S1 GE-8 IOA
•In a SRP-100 configuration, it must be installed in a turbo slot only (slot 2 or slot 4)
•If you install the line module in a slot other than slot 2 or slot 4, it will be disabled
•If you install the LM-10 module next to a configured line module that is already
installed in slot 3 or slot 5, the LM-10 module will be disabled
•If you install a line module in slot 3 or slot 5 next to a previously installed LM-10
module, the non-LM-10 module will be disabled
•In a SRP-120 and SRP-320 configuration, it can be installed in any slot
Description
•TFA ASIC
Type
•Supports a line rate of 128–byte frames on IOAs
•The 100–Gbps switch fabric allocates 3.4 Gbps of overall bandwidth to each regular
line module slot and 10 Gbps of overall bandwidth to each of the turbo slots (slot 2
and slot 4).
•The 120–Gbps and 320–Gbps switch fabrics allocate 10 Gbps of overall bandwidth
to each line module slot.
•See JunosE System Basics Configuration Guide, Chapter 6, Managing Modules for more
information.
Capability
•Not applicable
Software features
•Not applicable
Line module compatibility
•SRP-100
•SRP-120
•SRP-320
SRP module compatibility
•Yes (Redundancy IOA must be installed in either slot 0 or slot 11)
•Can only back up another ES2 10G LM
Line module redundancy
compatibility
•Not applicable
Port redundancy support
•Not applicable
Cables and connectors
When lit, LED indicates:
•OK (green)—Self-test passed
•FAIL (red)—Failure detected
•ONLINE (green)—Online with no alarms or errors
•REDUN (green)—Redundant card available
LEDs
9Copyright © 2010, Juniper Networks, Inc.
LM-10 Line Module

•See Monitoring Modules in JunosE System Basics Configuration Guide, Chapter 6,
Managing Modules.
Alarms, errors, and events
Copyright © 2010, Juniper Networks, Inc.10
E120 and E320 11.3.x Module Guide