Figure31:QFX10016SIB..............................................52
Figure 32: SIBs Installed in a QFX10016 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Figure33:SIBLEDs.................................................54
Chapter 7 Line Card Components and Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Figure34:QFX10000-36QPortPanel..................................56
Figure 35: All Ports Are Enabled for 40-Gigabit Ethernet by Default . . . . . . . . . . . 57
Figure 36: 100-Gigabit Ethernet Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 37: 100-Gigabit Ethernet Port Disables Two Associated 40-Gigabit
EthernetPorts..................................................57
Figure 38: Use the First and Fourth Port in Each 6XQSFP Cage to Channelize a
Port Range ....................................................58
Figure 39: LED Indicators for QSFP+ and QSFP28 Ports . . . . . . . . . . . . . . . . . . . . 60
Figure40:QFX10000-30CPortPanel..................................61
Figure 41: Disabled Ports in Channelization Mode . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure 42: Indicators for QSFP28 Ports on QFX10000-30C Line Cards . . . . . . . . 63
Figure 43: QFX10000-60S-6Q Port Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Figure 44: QFX10000-60S-6Q Port Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Figure 45: Supported Placement for Copper and Fiber SFP+ Transceivers . . . . . 68
Figure 46: Belly-to-Belly SFP Transceivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Figure 47: SFP+ Port Indicators and Status LEDs on a QFX10000-60S-6Q Line
Card..........................................................69
Figure 48: LED Indicators on QSFP+ and QSFP28 Ports on QFX10000-60S-6Q
LineCard......................................................69
Figure 49: QFX10K-12C-DWDM Port Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Figure 50: QFX10K-12C-DWDM Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Figure 51: DWDM Port and Ethernet Link State LEDs . . . . . . . . . . . . . . . . . . . . . . . 75
Figure52:LineCardLEDs............................................85
Part 2 Site Planning, Preparation, and Specifications
Chapter8 PreparationOverview.............................................105
Figure 53: Clearance Requirements for Airflow and Hardware Maintenance for
aQFX10008ModularChassis.....................................111
Figure 54: Clearance Requirements for Airflow and Hardware Maintenance for
aQFX10016ModularChassis......................................112
Part 3 Initial Installation and Configuration
Chapter 12 Unpacking and Mounting the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Figure 55: Shipping Crate and Accessory Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Figure56:BracketBoltRemoval......................................144
Figure57:UnpackingaLineCard......................................146
Figure 58: Mounting Brackets for Four-Post Rack Installation . . . . . . . . . . . . . . . 152
Figure 59: Loading the QFX10016 into a Rack Using a Mechanical Lift . . . . . . . . 154
Figure 60: Attaching Front-Mounting Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Figure 61: Front Panel Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Figure 62: Attaching Front Panel Brackets on a QFX10008 . . . . . . . . . . . . . . . . . 157
Figure 63: Attaching Front Panel Brackets on a QFX10016 . . . . . . . . . . . . . . . . . . 158
Figure 64: Front Panel Installation on a QFX10008 . . . . . . . . . . . . . . . . . . . . . . . 159
Copyright © 2017, Juniper Networks, Inc.x
QFX10016 Switch Hardware Guide
