Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV... User manual

E Series™ Broadband
Services Routers
ERX™ Module Guide
Release
11.3.x
Published: 2010-09-27
Copyright © 2010, Juniper Networks, Inc.

This guide provides an overview and description of the line modules (LMs), switch route
processor (SRP) modules, and I/O modules available for the following Juniper Networks
E Series Broadband Services Routers: ERX14xx models, ERX7xx models, and the ERX310
router.
Unless otherwise specified, all line modules pair with I/O modules to create a module
combination. Each module combination provides particular capabilities and connections
in an ERX router.
NOTE: A release may support multiple versions of a module. For information,
see Software Compatibility in JunosE System Basics Configuration Guide,
Chapter 6, Managing Modules.
Table 1 on page 3 lists the module combinations supported by ERX routers.
This book also contains three appendixes:
•Module Protocol Support on page 87
•Module LEDs on page 109
•Module Name Cross-Reference Information on page 115
•Product Reclamation and Recycling Program on page 119
For more information about ERX routers and modules, refer to the following books:
•Modules that have reached end-of-life—E Series End-of-Life Module Guide
•Module installation and maintenance—ERX Hardware Guide
•Managing ERX routers—JunosE System Basics Configuration Guide
•Configuring ERX modules—JunosE Link Layer Configuration Guide
Copyright © 2010, Juniper Networks, Inc.2
ERX 11.3.x Module Guide

Table 1: ERX Module Combinations
Page
First
JunosE
Support
I/O Module
Label
Line
Module
LabelCombination Name and Type
Fast Ethernet
85.0.0FE-8 I/OGE/FEFE-8 (8 ports) (256-MB memory)
96.0.0FE-8 SFP
I/O
GE/FEFE-8 SFP (8 ports) (256-MB memory)
Gigabit Ethernet (1-port)
115.0.0GE I/O SFPGE/FEGE 1000Base-SX (256-MB memory)
135.0.0GE I/O SFPGE/FEGE 1000Base-LH (256-MB memory)
155.0.0GE I/O SFPGE/FEGE 1000Base-ZX (256-MB memory)
172.0.0GE I/O
MULTI
MODE
GE/FEGE multimode
192.0.0GE I/O
SINGLE
MODE
GE/FEGE single-mode
Gigabit Ethernet (2-port)
215.3.0GE-2 SFP
I/O or
2XGE APS
I/O SFP or
GE-2 APS
I/O SFP
GE-2GE2 1000Base-SX
235.3.0GE-2 SFP
I/O or
2XGE APS
I/O SFP or
GE-2 APS
I/O SFP
GE-2GE2 1000Base-LH
255.3.0GE-2 SFP
I/O or
2XGE APS
I/O SFP or
GE-2 APS
I/O SFP
GE-2GE2 1000Base-ZX
3Copyright © 2010, Juniper Networks, Inc.

Table 1: ERX Module Combinations (continued)
Page
First
JunosE
Support
I/O Module
Label
Line
Module
LabelCombination Name and Type
GE High Density (HDE)
277.0.0GE-2 SFP
I/O or
2XGE APS
I/O SFP or
GE-2 APS
I/O SFP
GE-HDEGE High Density (2 ports)
297.0.0GE-8 I/OGE-HDEGE High Density (8 ports)
OC3/STM1 ATM
315.0.0, 5.3.0OC3-4 I/O
MULTI
MODE
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC3/STM1 ATM multimode without
APS/MSP redundancy (256-MB memory)
335.1.2
5.2.0
(APS/MSP)
4XOC3 APS
I/O
MULTI
MODE
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC3/STM1 ATM multimode with APS/MSP
redundancy
355.0.0, 5.3.0OC3-4 I/O
SINGLE
MODE
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC3/STM1 ATM single-mode intermediate
reach without APS/MSP redundancy
(256-MB memory)
375.1.2
5.2.0
(APS/MSP)
4XOC3
APS I/O
SINGLE
MODE
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC3/STM1 ATM single-mode intermediate
reach with APS/MSP redundancy
395.0.0, 5.3.0OC3-4 I/O
LONG HAUL
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC3/STM1 ATM single-mode long reach
without APS/MSP redundancy (256-MB
memory)
OC3/STM1 GE/FE
416.1.0OC3–2 GE
APS I/O
OC3/STM1
GE/FE
OC3/STM1 GE/FE
OC3/STM1 POS
Copyright © 2010, Juniper Networks, Inc.4
ERX 11.3.x Module Guide

Table 1: ERX Module Combinations (continued)
Page
First
JunosE
Support
I/O Module
Label
Line
Module
LabelCombination Name and Type
452.0.0OC3-4 I/O
MULTI
MODE
OCx/STMx
POS
OC3/STM1 POS multimode without
APS/MSP redundancy
475.1.2
5.2.0
(APS/MSP)
4XOC3 APS
I/O
MULTI
MODE
OCx/STMx
POS
OC3/STM1 POS multimode with APS/MSP
redundancy
492.0.0OC3-4 I/O
SINGLE
MODE
OCx/STMx
POS
OC3/STM1 POS single-mode intermediate
reach without APS/MSP redundancy
515.1.2
5.2.0
(APS/MSP)
4XOC3 APS
I/O
SINGLE
MODE
OCx/STMx
POS
OC3/STM1 POS single-mode intermediate
reach with APS/MSP redundancy
532.0.0OC3-4 I/O
LONG HAUL
OCx/STMx
POS
OC3/STM1 POS single-mode long reach
OC12/STM4 ATM
555.0.0, 5.3.0OC12 STM4
I/O
MULTI
MODE
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC12/STM4 ATM multimode without
APS/MSP redundancy (256-MB memory)
572.0.0 (128
MB)
5.0.0 (256
MB)
OC12 STM4
APS
MULTI
MODE
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC12/STM4 ATM multimode with
APS/MSP redundancy
595.0.0, 5.3.0OC12 STM4
I/O
SINGLE
MODE
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC12/STM4 ATM single-mode
intermediate reach without APS/MSP
redundancy (256-MB memory)
612.0.0 (128
MB)
5.0.0 (256
MB)
OC12 STM4
APS
SINGLE
MODE
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC12/STM4 ATM single-mode
intermediate reach with APS/MSP
redundancy
5Copyright © 2010, Juniper Networks, Inc.

Table 1: ERX Module Combinations (continued)
Page
First
JunosE
Support
I/O Module
Label
Line
Module
LabelCombination Name and Type
635.0.0, 5.3.0OC12 STM4
I/O
LONG HAUL
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC12/STM4 ATM single-mode long reach
without APS/MSP redundancy (256-MB
memory)
652.0.0 (128
MB)
5.0.0 (256
MB)
OC12 STM4
APS
LONG HAUL
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC12/STM4 ATM single-mode long reach
with APS/MSP redundancy
OC12/STM4 POS
672.0.0OC12 STM4
I/O
MULTI
MODE
OCx/STMx
POS
OC12/STM4 POS multimode without
APS/MSP redundancy
692.0.0OC12 STM4
APS
MULTI
MODE
OCx/STMx
POS
OC12/STM4 POS multimode with
APS/MSP redundancy
712.0.0OC12 STM4
I/O
SINGLE
MODE
OCx/STMx
POS
OC12/STM4 POS single-mode
intermediate reach without APS/MSP
redundancy
732.0.0OC12 STM4
APS
SINGLE
MODE
OCx/STMx
POS
OC12/STM4 POS single-mode
intermediate reach with APS/MSP
redundancy
752.0.0OC12 STM4
I/O
LONG HAUL
OCx/STMx
POS
OC12/STM4 POS single-mode long reach
without APS/MSP redundancy
772.0.0OC12 STM4
APS
LONG HAUL
OCx/STMx
POS
OC12/STM4 POS single-mode long reach
with APS/MSP redundancy
OC48/STM16
794.1.xOC48
FRAME APS
OC48OC48/STM16 POS single-mode short
reach
Copyright © 2010, Juniper Networks, Inc.6
ERX 11.3.x Module Guide

Table 1: ERX Module Combinations (continued)
Page
First
JunosE
Support
I/O Module
Label
Line
Module
LabelCombination Name and Type
Service Module (SM)
805.1.0No I/O
module
SERVICE
MODULE
SM
SRPs
814.1.3, 5.0.4,
5.1.2, 5.2.0
SRP I/OSRP-5G+SRP-5G+ (1-GB memory)
824.1.3, 5.0.4,
5.1.2, 5.2.0
SRP I/OSRP-10GSRP-10G (2-GB memory)
834.0.0SRP I/OSRP-40G
PLUS
SRP-40G PLUS (2-GB memory)
845.3.0SRP-SE I/OSRP-SE10GSRP-SE10G (1-GB memory)
T3
854.1.0 (128
104 MB)
5.0.0 (256
MB)
4xDS3 ATM
I/O
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
T3 ATM (4 ports)
7Copyright © 2010, Juniper Networks, Inc.

FE-8 Module Combination (8 Ports) (256-MB Memory)
GE/FE
Line module label
FE-8 I/O
I/O module label
•8
Number of I/O ports
•First supported: 5.0.0
•Final supported: Not applicable
•The GE/FE line module must have a minimum of 256 MB of memory to be used
with JunosE Release 5.3.0 or a higher-numbered release.
Software release
•130 W
•Fast Ethernet
Description
•EFA ASIC
Type
•IEEE 802.3 standards compliance
•10/100Base-T
Capability
•See “Ethernet Modules” on page 87 for information about the layer 2 and layer
3 protocols and applications that this module combination supports.
Software features
•ERX7xx models
•ERX14xx models
•ERX310 router
Model compatibility
•SRP-5G+
•SRP-10G
•SRP-40G
•SRP-40G PLUS
•SRP-SE10G
SRP module compatibility
•Not applicable
Module redundancy support
•RJ-45 connectors
•For 10-Mbps operation, use CAT 3, 4, or 5 UTP cable.
•For 100-Mbps operation, use only CAT 5 UTP cable.
•The transmitted signal complies with IEEE 802.3/802.3u for cable lengths up
to 100 m (328 feet).
•See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
Cables and connectors
•See “Module LEDs” on page 109.
LEDs
•See Monitoring Ethernet Interfaces in JunosE Physical Layer Configuration Guide,
Chapter 5, Configuring Ethernet Interfaces.
Alarms, errors, and events
Copyright © 2010, Juniper Networks, Inc.8
ERX 11.3.x Module Guide

FE-8 SFP Module Combination (8 Ports) (256-MB Memory)
GE/FE
Line module label
FE-8 SFP I/O
I/O module label
•8
Number of I/O ports
•First supported: 6.0.0
•Final supported: Not applicable
Software release
•130 W
•Fast Ethernet
•The FE-8 SFP I/O module uses a range of small form-factor pluggable (SFP)
transceivers to support different modes and cable lengths.
Description
•EFA ASIC
Type
•IEEE 802.3 standards compliance
•100Base-FX
Capability
•See “Ethernet Modules” on page 87 for information about the layer 2 and layer
3 protocols and applications that this module combination supports.
Software features
•ERX7xx models
•ERX14xx models
•ERX310 router
Model compatibility
•SRP-5G+
•SRP-10G
•SRP-40G
•SRP-40G PLUS
•SRP-SE10G
SRP module compatibility
•Not applicable
Module redundancy support
•LC full duplex
•Tx power:
•min: –15 dBm
•max: –8 dBm
•Center wavelength: 1300 nm
•Rx input power:
•min: –28 dBm
•max: –14 dBm
•Rated for 10 km (6.2 miles) over 9-micron core cable
•See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
Cables and connectors (single-mode
fiber)
9Copyright © 2010, Juniper Networks, Inc.
FE-8 SFP Module Combination (8 Ports) (256-MB Memory)

•LC full duplex
•Tx power: –20 dBm minimum and –14 dBm maximum
•Center wavelength: 850 nm
•Rx input power: –31 dBm minimum and –14 dBm maximum
•Rated for 2 km (1.2 miles) over 62.5/125-micron core cable
•See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
Cables and connectors (multimode
fiber)
•See “Module LEDs” on page 109.
LEDs
•See Monitoring Ethernet Interfaces in JunosE Physical Layer Configuration Guide,
Chapter 5, Configuring Ethernet Interfaces.
Alarms, errors, and events
Copyright © 2010, Juniper Networks, Inc.10
ERX 11.3.x Module Guide