Juniper MX2010 User manual

MX2010 Universal Roung Plaorm
Published
2023-10-05
RELEASE

Table of Contents
MX2010 Quick Start Descripon
Step 1: Prepare the Site for Installaon
Rack-Mounng Requirements | 2
Moving Requirements and Guidelines Using a Router Transport Kit | 5
Tools Required to Unpack and Prepare the Router for Installaon | 8
Step 2: Install the Mounng Hardware
Install the Mounng Hardware | 9
Step 3: Install the Router
Unpack the Router | 12
Remove Components | 15
Install the Router Using a Pallet Jack with Aachment | 22
Install the Pallet Jack Aachment | 22
Use the Pallet Jack with Aachment to Install the Router | 23
Install the Router Using a Router Transport Kit | 29
Unpack the Router Transport Kit | 29
Install the Router Transport Kit onto the Router | 33
Secure the Router to the Transport Plaorm | 35
Use the Router Transport Kit to Install the Router in a Four-Post Rack | 38
Use the Router Transport Kit to Install the Router in an Open-Frame Rack | 48
Step 4: Connect the Grounding Cable
Step 5: Reinstall Components
Step 6: Connect External Devices and Line Card Cables
Connect to a Network for Out-of-Band Management | 58
ii

Connect a Management Console | 58
Connect the Line Card Cables | 58
Step 7: Connect Power Cables
Connect Power to a Three-Phase Delta AC Power Distribuon Module | 60
Connect Power to a Three-Phase Wye AC Power Distribuon Module | 64
Connect AC Power Supply Modules | 68
Connect Power to a DC Power Distribuon Module | 71
Connect DC Power Supply Modules | 74
Step 8: Perform Inial Soware Conguraon
Enter Conguraon Mode | 78
Congure User Accounts and Passwords | 78
Congure System Aributes | 79
Commit the Conguraon | 81
Safety Warnings
iii

MX2010 Quick Start Descripon
This Quick Start contains informaon to help you quickly install and congure the MX2010 Universal
Roung Plaorm. For complete installaon instrucons, see the MX2010 Universal Roung Plaorm
Hardware Guide at hps://www.juniper.net/documentaon/.
WARNING: This Quick Start contains a summary of safety warnings in "Safety
Warnings" on page 82. For a complete list of warnings for this router, including
translaons, see the MX2010 Universal Roung Plaorm Hardware Guide at hps://
www.juniper.net/documentaon/.
The MX2010 Universal Roung Plaorm is shipped in a wooden crate. A wooden pallet forms the base
of the crate. The MX2010 chassis is bolted to this pallet. The shipping crate also contains a large rack
mount tray, electromagnec interference (EMI) cover, a cardboard accessory box, and a Quick Start (this
document).
NOTE: The shipping container and router (fully populated) weighs approximately 1343 lb (609.17
kg), depending on your conguraon.
The MX2010 Universal Roung Plaorm with standard cable managers and EMI cover measures
59.50 in. (151.13 cm) high, 19 in. (48.26 cm) wide, and 36.20 in. (91.95) deep (from the front-mounng
anges to the rear of the chassis). An extended cable manager extends the depth to 40.15 in. (102 cm).
One router can be installed in a 34-U or taller open-frame or four-post rack if the rack can support the
combined weight, which can be greater than 985 lb (445.79 kg).
NOTE: The dimensions also include the cable managers and EMI cover.
NOTE: If you are installing the MX2010 router into a network cabinet, make sure that no
hardware, device, rack, or cabinet components obstruct the 34-U rack space from access during
installaon.
The MX2010 router has 10 dedicated line-card slots, which means a maximum of 10 Modular Port
Concentrators (MPCs) including adapter cards (ADCs), and Modular Interface Cards (MICs), a host
subsystem consisng of two Control Board with Roung Engines (CB-REs), and eight Switch Fabric
Boards (SFBs).
1

Adapter cards provide housing to MPCs. The MPCs aach to the adapter cards, which in turn connect to
the backplane.
Up to two MICs can be installed in each MPC. Fully populated, the MX2010 router supports up to 20
MICs.
For a list of the supported MPCs and MICs, see the MX Series Interface Module Reference .
Step 1: Prepare the Site for Installaon
IN THIS SECTION
Rack-Mounng Requirements | 2
Moving Requirements and Guidelines Using a Router Transport Kit | 5
Tools Required to Unpack and Prepare the Router for Installaon | 8
Rack-Mounng Requirements
• You can install the router in an open-frame rack, a four-post rack, or a cabinet.
NOTE: The shipping and installaon site must be an ESD-approved area.
• The rack rails must be spaced widely enough to accommodate the chassis’s external dimensions:
59.50 in. (151.13 cm) high, 36.20 in. (91.95 cm) deep, and 19 in. (48.26 cm) wide (from the front-
mounng anges to the rear of the chassis). An extended cable manager extends the depth to 40.15
in. (102 cm). See Figure 1 on page 4 and Figure 2 on page 5).
In an open-frame rack, center-mounng is required to provide an even distribuon of weight for
greater stability. For center-mounng, use the mounng brackets aached to the center of the
chassis for rack mounng.
• The rack must be strong enough to support the weight of the fully congured router, up to 985 lb
(446.79 kg).
2

• For the cooling system to funcon properly, the airow around the chassis must be unrestricted.
Allow at least 36 in. (91.44 cm) of clearance between front-to-rear-cooled routers. Allow 2.8 in.
(7 cm) between the side of the chassis and any non-heat-producing surface such as a wall.
NOTE: To help redirect exhaust air away from the chassis, there is an oponal adjustable air
bae that can be installed on the upper fan tray access.
• For service personnel to remove and install hardware components, there must be adequate space at
the front and back of the router. Allow at least 36 in. (91.44 cm) in front of the router and
36 in. (91.44 cm) behind the router.
• The rack or cabinet must have an adequate supply of cooling air.
• Ensure that the cabinet allows the hot exhaust air of the chassis to exit from the cabinet without
recirculang into the router.
• The router must have the shipping covers installed to help move the router into the rack or cabinet.
• The router must be installed into a rack or cabinet that is secured to the building structure.
• The cabinet must be clear of any hardware, device, rack, or cabinet component that obstructs the 34-
U rack space from being access during installaon.
3

Figure 1: MX2010 Rack Clearance and Router Dimensions for Four-Post Rack
4

Figure 2: MX2010 Rack Clearance and Router Dimensions for Open-Frame Rack
Moving Requirements and Guidelines Using a Router Transport Kit
The router requires a minimum 42 in. (106.7 cm) diameter of space to turn the chassis on the router
transport kit (see Figure 3 on page 6).
5

NOTE: The router transport kit handles can be removed to accommodate aisle width.
Figure 3: Turning Diameter of Router Transport Kit
The weight of the router transport kit is 138.5 lb (63 kg). The maximum recommended height the router
should be lied from the oor using the router transport kit is 1.5 in. (3.8 cm).
Viewed from the side, the router with the router transport kit installed measures 59.50 in. (151.13 cm)
high and 36.20 in. (91.95 cm) wide, with the transport kit measuring 23.40 in. (59.4 cm) high (see Figure
4 on page 7).
6

Figure 4: Measurements of the Router Transport Kit Installed on the MX2010 (Side View)
Viewed from the front, the router with the router transport kit installed measures 30.78 in. (78.2 cm)
wide (see Figure 5 on page 8).
7