Juniper MX480 User manual

MX480 3D Universal Edge Router
Quick Start
January 2015
Part Number: 530-040794
Revision 01
This document describes how to install the Juniper Networks®MX480 3D Universal Edge
Router.
Contents MX480QuickStartDescription.........................................3
Step 1: Prepare the Site for MX480 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Rack-MountingRequirements......................................4
Tools Required to Unpack and Prepare the MX480 Router for
Installation ..................................................5
Step 2: Install the Mounting Hardware in a Four-Post Rack or Cabinet or an
Open-FrameRack................................................6
Step3:InstalltheRouter..............................................9
RemoveComponents.............................................9
InstalltheRouterUsingaLift......................................10
Install the Router Without a Mechanical Lift . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ReinstallComponents............................................13
Step4:ConnecttheGroundingCable...................................14
Step 5: Connect External Devices and Line Card Cables . . . . . . . . . . . . . . . . . . . . . 15
Connect to a Network for Out-of-Band Management . . . . . . . . . . . . . . . . . . . 15
ConnectaManagementConsole...................................15
ConnecttheLineCardCables......................................15
Step6:ConnectPowerCables.........................................17
Connect Power to an AC Router with Normal-Capacity Power Supplies . . . . 17
Connect Power to an AC Router with High-Capacity Power Supplies . . . . . . . 17
Connect Power to a DC Router with Normal-Capacity Power Supplies . . . . . 18
Connect Power to a DC Router with High-Capacity Power Supplies . . . . . . . 20
Step 7: Perform Initial Software Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
EnterConfigurationMode.........................................23
Configure User Accounts and Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ConfigureSystemAttributes......................................24
CommittheConfiguration........................................24
SafetyWarnings....................................................26
1Copyright © 2015, Juniper Networks, Inc.

ComplianceStatementsforNEBS.....................................27
Compliance Statements for EMC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Canada .......................................................28
EuropeanCommunity............................................28
Israel .........................................................28
Japan.........................................................28
United States ..................................................29
Junos Documentation and Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
RequestingTechnicalSupport........................................30
Self-Help Online Tools and Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
OpeningaCasewithJTAC.........................................31
RevisionHistory.....................................................31
Copyright © 2015, Juniper Networks, Inc.2
MX480 3D Universal Edge Router Quick Start

MX480 Quick Start Description
This Quick Start contains information you need to install and configure the router quickly.
For complete installation instructions, see the MX480 3D Universal Edge Router Hardware
Guide at http://www.juniper.net/techpubs/.
WARNING: This Quick Start contains a summary of safety warnings in “Safety
Warnings” on page 26. For a complete list of warnings for this router, including
translations, see the MX480 3D Universal Edge Router Hardware Guide at
http://www.juniper.net/techpubs/.
The MX480 3D Universal Edge Router is 8 rack units (U) tall. Five routers can be stacked
in a single floor-to-ceiling rack, for increased port density per unit of floor space. The
router provides eight slots that can be populated with up to six Dense Port Concentrators
(DPCs) or Modular Port Concentrators (MPCs), three Flexible PIC Concentrators (FPCs),
and two SCBs. Each FPC holds up to two PICs and each MPC holds up to two Modular
Interface Cards (MICs).
Each Packet Forwarding Engine enables a throughput of 10 Gbps. Many types of DPCs
are available. For a list of the DPCs supported, see the MX Series 3D Universal Edge
Routers Line Card Guide.
The MX480 supports up to 3 FPCs containing up to 6 PICs or up to 6 MPCs containing
up to 12 MICs. For a list of the supported line cards, see the MX Series Interface Module
Reference.
The router is shipped in a cardboard box strapped securely to a wooden pallet. Plastic
straps secure the top and bottom in place. The router chassis is bolted to this pallet.
Quick Start installation instructions and a cardboard accessory box are also included in
the shipping container.
3Copyright © 2015, Juniper Networks, Inc.
MX480 Quick Start Description

Step 1: Prepare the Site for MX480 Installation
•Rack-Mounting Requirements on page 4
•Tools Required to Unpack and Prepare the MX480 Router for Installation on page 5
Rack-Mounting Requirements
•You can install the router in a four-post rack or cabinet or an open-frame rack.
•The rack rails must be spaced widely enough to accommodate the router chassis's
external dimensions: 14.0 in. (35.6 cm) high, 24.5 in. (62.2 cm) deep, and
17.45 in. (44.3 cm) wide. The outer edges of the mounting brackets extend the width
to 19 in. (48.3 cm).
•The rack must be strong enough to support the weight of the fully configured router,
up to 163.5 lb (74.2 kg). If you stack five fully configured routers in one rack, it must be
capable of supporting about 818 lb (371.0 kg).
•For service personnel to remove and install hardware components, there must be
adequate space at the front and back of the router. Allow at least 30 in. (76.2 cm) in
front of the router and 24 in. (61 cm) behind the router.
•The rack or cabinet must have an adequate supply of cooling air.
•Ensure that the cabinet allows the chassis hot exhaust air to exit from the cabinet
without recirculating into the router.
•The router must be installed into a rack that is secured to the building structure.
•Mount the router at the bottom of the rack if it is the only unit in the rack.
•When mounting the router in a partially filled rack, load the rack from the bottom to
the top with the heaviest component at the bottom of the rack.
Copyright © 2015, Juniper Networks, Inc.4
MX480 3D Universal Edge Router Quick Start

Figure 1: MX480 Rack Clearance and Router Dimensions
Tools Required to Unpack and Prepare the MX480 Router for Installation
To unpack the router and prepare for installation, you need the following tools:
•A mechanical lift—recommended
•Phillips (+) screwdrivers, numbers 1 and 2
•2.5-mm flat-blade (–) screwdriver
•7/16-in. (11 mm) torque-controlled driver or socket wrench
•1/2-in. or 13-mm open-end or socket wrench to remove bracket bolts from the shipping
pallet
•Electrostatic discharge wrist strap
•Antistatic mat
5Copyright © 2015, Juniper Networks, Inc.
Tools Required to Unpack and Prepare the MX480 Router for Installation

Step 2: Install the Mounting Hardware in a Four-Post Rack or Cabinet or an Open-Frame
Rack
To install the mounting shelf on the front rails of a four-post rack or cabinet, or the rails
of an open-frame rack:
1. If needed, install cage nuts in the holes specified in Table 1 on page 6.
2. On the back of each rack rail, partially insert a mounting screw into the lowest hole
specified in Table 1 on page 6.
3. Install the mounting shelf on the back of the rack rails. Rest the bottom slot of each
flange on a mounting screw.
4. Partially insert screws into the open holes in each flange of the mounting shelf (see
Figure 2 on page 7 or Figure 3 on page 8).
5. Tighten all the screws completely.
Table 1: MX480 Mounting Hole Locations
Mounting ShelfDistance Above U DivisionHole
X1.14 U2.00 in. (5.1 cm)4
X0.86 U1.51 in. (3.8 cm)3
X0.50 U0.88 in. (2.2 cm)2
X0.14 U0.25 in. (0.6 cm)1
Copyright © 2015, Juniper Networks, Inc.6
MX480 3D Universal Edge Router Quick Start

Figure 2: MX480 Mounting Hardware for a Four-Post Rack or Cabinet
g004258
Four-post open rack
Small mounting shelf
7Copyright © 2015, Juniper Networks, Inc.
Step 2: Install the Mounting Hardware in a Four-Post Rack or Cabinet or an Open-Frame Rack

Figure 3: Mounting Hardware for an Open-Frame Rack
Copyright © 2015, Juniper Networks, Inc.8
MX480 3D Universal Edge Router Quick Start

Step 3: Install the Router
Because of the router's size and weight, you must remove all components before installing
the router. We also recommend that you install the router using a mechanical lift.
•Remove Components on page 9
•Install the Router Using a Lift on page 10
•Install the Router Without a Mechanical Lift on page 12
•Reinstall Components on page 13
Remove Components
Figure 4: Components to Remove from the Front of the MX480 Router
Figure 5: Components to Remove from the Rear of the MX480 Router
Before lifting the router, you must remove the following components:
•Power supplies
•Switch Control Boards (SCBs)
9Copyright © 2015, Juniper Networks, Inc.
Step 3: Install the Router

•Routing Engines
•Air filter
•Fan tray
•Line cards:
•Dense Port Concentrators (DPCs)
•Flexible PIC Concentrators (FPCs)
•Physical Interface Cards (PICs)
•Modular Port Concentrators (MPCs)
•Modular Interface Cards (MICs)
To remove the components from the router:
1. Slide each component out of the chassis evenly so that it does not become stuck or
damaged.
2. Label each component as you remove it so you can reinstall it in the correct location.
3. Immediately store each removed component in an electrostatic bag.
4. Do not stack removed components. Lay each one on a flat surface.
NOTE: For complete instructions on removing router components, see
“Installing the MX480 Chassis in the Rack Manually” in the MX480 Router
Hardware Guide.
Install the Router Using a Lift
To install the router using a lift:
1. Ensure that the rack is in its permanent location and is secured to the building. Ensure
that the installation site allows adequate clearance for both airflow and maintenance.
For details, see the MX480 3D Universal Edge Router Hardware Guide.
2. Load the router onto the lift, making sure it rests securely on the lift platform (see
Figure 6 on page 11).
Copyright © 2015, Juniper Networks, Inc.10
MX480 3D Universal Edge Router Quick Start