Juuko B0129 User manual
User Manual
Model: B0129
Product Description
The B0129 RF Transceiver Module is a compact surface-mounted module for multi- channel RoLa
operation in the 2400 MHz ISM band. The module is completely shielded and pre-certied for
operation under US radio regulations for license-free use.
Technical data
Block Diagram
Theory of Operation/Technical Description
- RF circuit function:
The major part of this IC is a 2401-2478 MHz compliant
transceiver.
- RF signal ow:
The Control signal is encoded into a Data Stream to be the
modulation input for the transceiver.
-Description of Antenna system:
The antenna shall be connected to the RF pin. The RF pin is
matched to 50 Ohm. If the antenna connector is placed
away from the module at the motherboard, the track
between the RF pin and the connector should be a 50 Ohm
transmission line.
RF
Tranceiver
CC1200
Filter
1.8-3.7 V
SI
SCLK
SO
RESET
GPIO
CSN
GND
Pin Assignment
GND
ANT
GND
VCC
SI
SCLK
SO
RESET
GPIO
CSN
GND
The nal host product must be submitted to SHUN
HU Technology Co., Ltd. for conrmation that the
installation of the module into the host is in
compliance. with the regulations of FCC and IC
Canada. Specically, if an antenna other than the
model documented in the Filing is used, a Class 2
Permissive Change must be led with the FCC.
TCXO
52Mhz
Dimensions
Frequency
Modulation method
Channel bandwidth
Supply voltage
30.38×18.5×7.45(mm)
2.4GHz
RoLa
500KHz
Temperature range -40°C+85°C
1.8-3.7 Volt
RN489896162JK915
FCC ID
RN489896162-B0129
FCC ID
User Manual
Mechanical Drawing
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interfer-
ence that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisa-
teur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en comprom-
ettre le fonctionnement.
FCC Part 15
* This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference and (2) this device must accept any interference received, including interference that may
cause undesired operation
* You are cautioned that changes or modications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
Antenna gain: 2dBi
C
2.5
20.6
18
1.6
2.1
5
2.5
1.2
4.8
18.5
30.4
14.2
5
7.5
Label
User Manual
The module has received Federal Communications Commission (FCC) CFR47 Telecommunications, Part 15 Subpart C
"Intentional Radiators" modular approval in accordance with Part 15.212 Modular Transmitter approval. Modular approval
allows the end user to integrate the module into a nished product without obtaining subsequent and separate FCC
approvals for intentional radiation, provided no changes or modications are made to the module circuitry. Changes or
modications could void the user's authority to operate the equipment. The end user must comply with all of the
instructions provided by the Grantee, which indicate installation and/or operating conditions necessary for compliance.
The nished product is required to comply with all applicable FCC equipment authorizations regulations, requirements and
equipment functions not associated with the transmitter module portion. For example, compliance must be demonstrated
to regulations for other transmitter components within the host product; to requirements for unintentional radiators (Part
15 Subpart B "Unintentional Radiators"), such as digital devices, computer peripherals, radio receivers, etc.; and to additional
authorization requirements for the nontransmitter functions on the transmitter module (i.e., Verication, or Declaration of
Conformity) (e.g., transmitter modules may also contain digital logic functions) as appropriate.
LABELING AND USER INFORMATION REQUIREMENTS
The
B0129
module has been labeled with its own FCC ID number, and if the FCC ID is not visible when the module is installed
inside another device, then the outside of the nished product into which the module is installed must also display a label
referring to the enclosed module. This exterior label can use wording as follows:
Contains Transmitter Module FCC ID:
RN489896162-B0129 or Contains FCC ID: RN489896162-B0129
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation
A user's manual for the nished product should include the following statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Additional information on labeling and user information requirements for Part 15 devices can be found in KDB Publication
784748 available at the FCC Oce of Engineering and Technology (OET) Laboratory Division Knowledge Database (KDB)
http://apps.fcc.gov/oetcf/kdb/index.cfm.
RF EXPOSURE
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located
or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna
installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
Other Juuko Transceiver manuals
