Juvent 1000 User manual

UVENT
J
UVENT
J
Dynamic Motion Therapy
Instruction Manual

2Juvent 1000 Instruction Manual
Table of Contents
Symbols Used for the Juvent DMT Platform
Juvent Device and RFID Rail Stand Set Up Procedure
Precautions
Medical Device Warnings and Precautions
Indications for Use
Medical Device Description
Disposing of the Medical Device
System Specifications
Environmental Conditions That Affect Use
Electrical Requirements
Operating Instructions
Care of the Juvent 1000
Storage of the Juvent 1000
FCC Information
Troubleshooting
3
11
12
13
14
15
16
17
18
18
19
23
23
24
27

Juvent Device and RFID Rail Stand Set Up Procedure
3Juvent 1000 Instruction Manual
Remove the rail stand from the box and assemble it using the following instructions
and tools.
Authorized Representative
Juvent Ltd.
46 Offington Park
Sutton
Dublin 13, Ireland
Tel: [phone]
Manufactured For:
Juvent Inc.
300 Atrium Dr.
Somerset, NJ USA
Tel: [phone]
P/N: J300155 Rev A
Juvent
1000 Rail Stand
Model No: J100044
3 Side Rail Assembly1
4 Hand Rail Adjust Tubes2
5 Rail Mast Fitting1
6 Side Rail Clamp1
7 Mast Weldment1
8 Strut Tube1
9 Base Frame Weldment1
10 Card1
Parts List Call Out

Assembly Process
4Juvent 1000 Instruction Manual
A
A
Orientation
Markers
Steps
1. Place base onto floor.
2. Remove screws.
3. Insert mart into base tubes.
4. Mount strut tube.
5. Reassemble screws and tighten.
6. Slide chrome tube up to
second hole location.
7. Remove the screw, Slide
handle bar onto chrome
tube, and slide tray
assembly into chrome tube.
8. Reassemble screw and
tighten.
Chrome Tube
Handle bar
shown removed
Tray
Tilt adjust
knob
Screw
SECOND
HOLE

Assembly Process
5Juvent 1000 Instruction Manual
10. Removed base tube screws.
Slide the hand rail assembly
into the base tubes.
Reassemble the rail mast
fitting and reassemble base
tube screws. Then tighten.
9. Slide the hand rail adjust tubes
onto the side rails. Snap into first
hole.

6Juvent 1000 Instruction Manual
Juvent RFID System Bill of Materials
The RFID setup kit contains the following:
1. J100014: Juvent 1000 production plate assembly modified for
RFID-controlled use.
2. J200118: Juvent RFID system power supply.
3. J200117: Serial RS-232 male-to-male null-modem cable.
4. J300159: Juvent 1000 RFID system full instruction manual.
5. J300161: Juvent 1000 RFID system one-page manual
6. J100044: Railstand assembly modified for RFID use.
7. J100051: RFID reader assembly (is pre-attached to railstand by
Juvent).
8. A length of Velcro cable-attachment banding.
9. J700018: Proper Posture Card.

Set Up Procedure
7Juvent 1000 Instruction Manual
1. Remove the Juvent 1000 Device
from its box and place it on the
stand as shown. (Figure 1)
Figure 1
2. Connect one end of the RS-232
serial cable to the 9-pin connector on
the RFID box, as shown in Figure 2. Two
screws are provided on the serial
connector; use them to lock the connector
in place. If using a screwdriver, be careful
not to overtighten the screws.
3. The Juvent system power supply has two
output cords. With the power supply on
the floor, only one cord will reach the
RFID unit. Plug the longer cord into the
RFID unit as shown in Figure 3.
Figure 2
Figure 3

8Juvent 1000 Instruction Manual
4. The cables for the RFID unit are to be
run down the outside of the center pole,
on the side facing away from the user.
Secure the cables with approximately
4 inches of the Velcro supplied.
(Figure 4)
NOTE: Do not make the bend too tight
in the cables exiting the RFID unit.
5. As the cables exit the RFID unit,
position the cables as shown in Figure
5, using more lengths of Velcro.
6. Continue by fastening the cables in the
center of the middle pole. Fasten the
cables near the base of the pole. Peel
the liner of the double sided tape on
back of the power supply and place onto
the bar. Affix power supply with two
longer Velcro strips.
(Figure 6 and 7)
Route the power supply cable through
the retaining clip as shown.
(Figure 8)
Figure 4
Figure 5
Figure 6
Figure 7 Figure 8

Juvent 1000 Instruction Manual
7. Connect the free end of the RS-232 cable
to the Juvent 1000 device as shown in
Figure 9. Tighten the two screws, but do
not overtighten.
Plug the free end of the power supply cord
into the Juvent 1000 as shown in
Figure 10.
8. Plug the AC power plug into an AC
outlet (Ensure the outlet is not
controlled by a wall switch).
9. Turn on the Juvent 1000 power switch.
(Figure 11)
10. At this point the device and RFID
“Standby” indicators should be on.
Figure 9
Figure 10
Figure 11
9

10 Juvent 1000 Instruction Manual
Test Operation
11. Stand on the device and place your special Juvent test card over the “Start
Treatment” area and verify the following:
A. The red RFID standby indicator went off and the green treatment
indicator turned on.
B. The device’s blue LCD lights up.
C. The device runs through the 12 second “Self test cycle” and begins the
10 minute treatment countdown.
If your first card did not activate the system, repeat the test operation with the second
card.
12. If the system still does not activate, check all connections.
13. Troubleshooting: See page 24 or call Juvent engineering - 1-877-209-9600
NOTE: Periodically ensure that all electrical connections are properly in place.

11Juvent 1000 Instruction Manual
Power has been turned on. Juvent
1000 is in standby mode, and will
begin treatment when user steps
on the Platform.
Juvent 1000 is calibrating system
parameters to the user.
Standby
Calibration
Juvent 1000 is in pause mode.Pause
Alerts user to refer to the manual.
Attention icon will display with
another icon.
Attention
Juvent 1000 has sensed a
malfunction. Flashes in
conjunction with Attention symbol.
Malfunction
Juvent 1000 has a low battery.
Battery needs to be recharged
(not operational at present time).
Battery
Symbols Used in the Operation of the
Juvent 1000 DMT Platform
Symbol Name Description

12
Precautions
Juvent 1000 Instruction Manual
There have been no reports of adverse effects with the use of the Juvent 1000 DMT
Platform to date. This includes thousands of treatments in children, adolescents,
and adult women and men.
Juvent, Inc. feels a responsibility to provide as much information as possible to
potential users. The following listing of precautions was developed from expertise
with the technology and potential physiological effects.
The use of the Juvent 1000 DMT Platform has not been evaluated on the
following conditions. Individuals with the following conditions or implants should
consult their physician before using the medical device:
• pregnancy
• congestive heart failure
• past history of deep vein thrombosis and/or pulmonary embolism
• history of thrombophlebitis within 5 years
• sensitivity to motion sickness
• known retinal conditions (eye)
• joint implants
• pacemakers and implantable cardioverter defibrillators (ICDs)
• treatment/surgery for spinal conditions (eg., sciatica-acute phase,
symptomatic spinal stenosis)

13Juvent 1000 Instruction Manual
Medical Device Warnings and Precautions
• There are no user serviceable parts in the Juvent 1000 Dynamic
Motion Therapy Platform. If problems arise, see troubleshooting section.
• If the Juvent 1000 fails to work, refer to the troubleshooting guide on
pages 24 and 25. If the medical device still fails to work, contact your
local Juvent distributor.
• Do not attempt to repair the device.
• The Juvent 1000 is an electromagnetic device which could
interfere with or be interfered with by other electromagnetic devices.
If interference occurs or the Juvent 1000 interferes with other
devices, relocate the medical device.
• To completely isolate the Juvent 1000 from power, unplug the
medical device from the wall receptacle. The power cord on the
external power supply is regarded as the disconnect source.
• To prevent damage to the Juvent 1000, unplug the device
during lightning storms.
• Unplug the medical device when unused for long periods of time.
• Cleaning instructions: Disconnect the device from the outlet
and clean with a soft cloth dampened with water. A mild soap can be
used if necessary.
• Be careful not to drop the device.
• Do not place the medical device in water or operate in a wet
environment, i.e., a shower stall, etc.
• Do not let objects or liquids enter the device.
• Keep the medical device away from radiators and any heat sources.
• Do not drop any objects onto the device.
• Do not jump on the device.
• Only use the supplied, approved medical grade Juvent power adapter.

14 Juvent 1000 Instruction Manual
Medical Device Warnings and Precautions (Cont.)
• The Juvent 1000 is a medical device which may require special
precautions regarding electromagnetic compatibility (EMC), and must be
installed and put into service according to the EMC information provided.
• The use of accessories, transducers or cables other than those specified,
with exception of those sold by Juvent as replacement parts for internal
components, may result in increased emissions or decreased immunity
of the system.
The Juvent 1000 DMT Platform is Indicated for
• maintaining and/or increasing bone density,
• restoring the fast-twitch action of Type IIA muscle fibers in
the lower legs,
• stimulating blood and lymph flow from the lower limbs to the heart.

15
Medical Device Description
The Juvent 1000 Dynamic Motion Therapy Platform
Information
Display
Standby LED
Therapeutic
Platform
RS232 Port Power Connector On/Off Switch –
shown in “off”
position
Connection Panel
Treatment Indicator
Juvent 1000 Instruction Manual

16 Juvent 1000 Instruction Manual
Medical Device Description
Disposing of the Medical Device
The Juvent 1000 Dynamic Motion Therapy Platform contains electronic
equipment that could have a potential effect on the environment if not
disposed of properly. When disposing of the Juvent 1000 becomes
necessary, the medical device must not be disposed with domestic
waste. Please contact your local Juvent distributor for information on
recycling the device properly.
The Juvent 1000 Dynamic Motion Therapy Platform is an easy-to-use
medical device that delivers a 10-minute daily treatment. The Juvent
1000 does not use any motors, cams or eccentric weights. The Plat-
form does use a patented single spring, actuator driven, unique four-
point suspension system that stabilizes the action of the Platform while
offering a significant mechanical advantage.
These features allow the Juvent 1000 to be in mechanical resonance
with the body mass of the user by adjusting the frequency of the
vibration to the size of the individual standing on the medical device. It
also results in a very efficient and gentle therapy that requires little
power to operate (less than 7.5 watts, or less than the power of a
nightlight).
The Juvent 1000 Platform is made of a rigid aluminum plate for the
vibration surface. This surface is covered by a biocompatible mat for
comfort. The Platform is enclosed by a two-piece plastic housing
module with a built-in handle for easy transport. The rigid aluminum
plate and the rugged, molded two-piece top/bottom housing are
designed for many years of dependable service.
When a user stands on the surface of the Platform in stocking feet, a
gentle mechanical vertical pulsation (displacement) is applied to the
bottom of their feet. The Juvent 1000 incorporates a microprocessor
controlled, automatic gain control to ensure that the correct signal is
constantly delivered to the user.

17Juvent 1000 Instruction Manual
System Specifications
System Weight 20.5 lbs (9.2 Kg)
System Dimensions
)ni57.3(mc35.9thgieH
)ni1.12(mc6.35htdiW
)ni7.32(mc2.06htpeD
Power Supply
zH06-05castlov042-001rewoptupnI
Power supply output voltage 15 volts DC
Power consumption less than 7.5 watts
Environmental Temperature
41º F to 100º F (10º C to 38º)gnit
arepO
32º F to 118º F (0º C to 45º C)egarotS
Relative humidity 10% to 90% (noncondensing)
Atmospheric pressure range 500 hPa to 1060 hPa
Medical Device Materials
Displacement platform module Aluminum
Housing module ABS plastic, flame-retardant
elbitapmocoiBtaM
Signal Parameters
Displacement frequency 32-37 Hz -0/+2%
Acceleration “g” force 0.3 g (peak to peak) (+/-20%)
Vertical displacement ~85 µm (0.085 mm)
Treatment time 10 minutes daily
suounitnoCelcycytuD
System Load
Normal operating load >35 lbs to 249 lbs
(> 15.8 Kg to 113.5 Kg)
Maximum operating load 250 lbs (113.6 Kg)
Maximum limit, nonoperating 310 lbs (140 Kg)

18 Juvent 1000 Instruction Manual
Environmental Conditions That Affect Use
WARNING!
The Juvent 1000 Dynamic Motion Therapy Platform is a line operated electrical medical
device. Do not use the Juvent 1000 in or near water. Doing so can cause injury and/or death.
The Juvent 1000 is an electromagnetic medical device which could interfere with or be
interfered with by other electromagnetic devices. If the Juvent 1000 is subject to
interference or interferes with other equipment, relocate the medical device.
Electrical Requirements
Medical Device
Type B applied part.
Power Input: 15 VDC 1.2A
Type of Current: DC
Medical Grade Power Adapter (Juvent part number J200079)
CAstlov042-001rewoptupnI
Power supply output voltage 15 volts DC
Power consumption less than 7.5 watts
Power supply operating range 50-60 Hz
Power supply polarity

Juvent 1000 Instruction Manual 19
1. Step onto the device carfully (Make
sure you are in stocking feet).
(Figure 1)
2. To start your therapy, hold the
treatment card over the indicated
area (on the lower left corner of the
tray) until the green light turns on and
you hear the device start to run. Now
remove your card. (Figure 2)
3.
Operating Instructions
Stand up straight and relax without
bending your knees. (Figure 3)
4. The Juvent 1000 Platform
performs a four-second self-test to
make sure that everything is
working properly.
5. After the self-test, a 12-second
calibration takes place to
determine your body mass.
Note: During this calibration,
the display screen shows the total
number of treatments that the
device has completed to date .
At the end of the 12 seconds, the
treatment begins.
Figure 1
Figure 2
Figure 3

20 Juvent 1000 Instruction Manual
6. Once treatment starts, the number
on the display screen will show
10:00 and continue to countdown
to zero.
7. At the end of the treatment,
the Juvent 1000 will automatically
shut off.
Operating Instructions (Cont.)
Step carefully off the device.
(Figure 4)
Treatment Interruption
Figure 4
If you step off the Juvent Platform at any time during the treatment
the device will beep once and automatically go into pause mode
for twenty seconds. If you stay off the platform for more than twenty
seconds, it will automatically shut off.
If you return to the platform before twenty seconds, the treatment will
resume.