Jvc Gy-hm150u User manual

HD MEMORY CARD CAMERA RECORDER

GY-HM150U

GY-HM150E

INSTRUCTIONS

* The illustration shows the GY-HM150U/GY-HM150E with the supplied microphone attached.

For Customer Use:

Enter below the Serial No. which is located on the body.

Retain this information for future reference.

Model No. GY-HM150U

Serial No.

Please read the following before getting started:

Thank you for purchasing this JVC product.

Before operating this unit, please read the instructions

carefully to ensure the best possible performance.

In this manual, each model number is described without the last letter

(U/E) which means the shipping destination. (U: for USA and Canada,

E: for Europe)

Only “U”models (GY-HM150U) have been evaluated by UL.

LST1229-001A

GY-HM150U.book Page 1 Monday, September 5, 2011 1:48 AM

Introduction

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use thisapparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’sinstructions.

8. Do not install near any heat sourcessuch

as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9. Protect the power cord from being walked on or pinche

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

10. Only use attachments/accessoriesspecified by the

manufacturer.

11. Use only with the cart,

stand, tripod, bracket,

or table specified by

the manufacturer, or

sold with the apparatus.

When acart isused,

use caution when

moving the cart/

apparatus combination

to avoid injury from tip-over.

12. Unplug thisapparatus during lightning stormsor

when unused for long periodsof time.

13. Refer all servicing to qualified service personnel.

Servicing isrequired when the apparatus has

been damaged in any way, such as power-supply

cord or plug isdamaged, liquid has been spilled

or objectshave fallen into the apparatus, the

apparatus has been exposed to rain or moisture,

doesnot operate normally, or has been dropped.

ThisClass B digital apparatus complieswith

Canadian ICES-003.

Cet appareil numérique de laclasse B est

conforme à lanorme NMB-003 duCanada.

Safety Precautions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTSINSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, isintended to alert the user to the

presence of uninsulated "dangerous voltage" within the

product'senclosure that may be of sufficient magnitude

to constitute arisk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructionsin

the literature accompanying the appliance.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTSINSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, isintended to alert the user to the

presence of uninsulated "dangerous voltage" within the

product'senclosure that may be of sufficient magnitude

to constitute arisk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructionsin

the literature accompanying the appliance.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTSINSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, isintended to alert the user to the

presence of uninsulated "dangerous voltage" within the

product'senclosure that may be of sufficient magnitude

to constitute arisk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructionsin

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THISUNIT TO

RAIN OR MOISTURE.

NOTES:

• The ratingplate and safety caution are on the

bottom and/or the back of the main unit.

• The serial number plate ison the battery pack

mount.

• The ratinginformation and safety caution of the

AC adapter are on itsupper and lower sides.

Caution on Replaceable lithium battery

The battery used in thisdevice may present afire

or chemical burn hazard if mistreated.

Do not recharge, disassemble, heat above 100°C

or incinerate.

Replace battery with Panasonic, Sanyo, Sony or

Maxell CR2025.

Danger of explosion or Risk of fire if the battery is

incorrectly replaced.

• Dispose of used battery promptly.

• Keep away from children.

• Do not disassemble and do not dispose of in fire.

For USA-California Only

Thisproduct containsaCR Coin Cell Lithium

Battery which containsPerchlorate Material

– special handling may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate

GY-HM150U.book Page II Monday, September 5, 2011 1:48 AM

III

When the equipment isinstalled in acabinet or on

ashelf, make sure that it has sufficient space on all

sidesto allow for ventilation (10 cm (3-15/16") or

more on both sides, on top and at the rear).

Do not block the ventilation holes.

(If the ventilation holesare blocked by a

newspaper, or cloth etc. the heat may not be able

to get out.)

No naked flame sources, such as lighted candles,

should be placed on the apparatus.

When discarding batteries, environmental

problemsmust be considered and the local rulesor

lawsgoverning the disposal of these batteriesmust

be followed strictly.

The apparatus shall not be exposed to dripping or

splashing.

Do not use thisequipment in abathroom or places

with water.

Also do not place any containersfilled with water

or liquids(such as cosmeticsor medicines, flower

vases, potted plants, cupsetc.) on top of thisunit.

(If water or liquid isallowed to enter this

equipment, fire or electric shock may be caused.)

Do not point the lensdirectly into the sun. This

can cause eye injuries, as well as lead to the

malfunctioning of internal circuitry. There isalso a

risk of fire or electric shock.

CAUTION!

Connecting cables(Audio/Video, etc.) to the

cameraand leaving it on top of the TV isnot

recommended, as tripping on the cableswill cause

the camerato fall, resulting in damage.

The following notesconcern possible physical

damage to the cameraand to the user.

Carrying or holding the cameraby the LCD monitor

can result in dropping the unit, or in amalfunction.

Do not use atripod on unsteady or unlevel surfaces. It

could tip over, causing serious damage to the camera.

CAUTION:

The mainsplug shall remain readily operable.

WARNING:

The battery pack, the camerawith battery installed,

and the remote control with battery installed should

not be exposed to excessive heat such as direct

sunshine, fire or the like.

Declaration of Conformity

Model Number : GY-HM150U

Trade Name : JVC

Responsible party : JVC AMERICASCORP.

Address : 1700 Valley Road Wayne, N. J. 07470

Telephone Number : 973-317-5000

Thisdevice complieswith Part 15 of FCC

Rules. Operation issubject to the following

two conditions: (1) Thisdevice may not cause

harmful interference, and (2) thisdevice must

accept any interference received, including

interference that may cause undesired operation.

Changesor modificationsnot approved by

JVC could void the user’sauthority to operate

the equipment. Thisequipment has been

tested and found to comply with the limitsfor

aClass B digital device, pursuant to Part 15 of

the FCC Rules. These limitsare designed to

provide reasonable protection against harmful

interference in aresidential installation. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instructions,

may cause harmful interference to radio

communications. However, there isno guarantee

that interference will not occur in aparticular

installation. If thisequipment doescause harmful

interference to radio or television reception,

which can be determined by turning the

equipment off and on, the user isencouraged

to try to correct the interference by one or more

of the following measures: Reorient or relocate

the receiving antenna. Increase the separation

between the equipment and receiver.

Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/

TV technician for help.

When usingthe AC adapter in areasother than

the USA

The provided AC adapter featuresautomatic voltage

selection in the AC range from 110 V to 240 V.

USING HOUSEHOLD AC PLUG ADAPTER

In case of connecting the unit’spower cord to

an AC wall outlet other than American National

Standard C73 seriestype use an AC plug adapter,

called a“SiemensPlug”, as shown.

For thisAC plug adapter, consult your nearest

JVC dealer. PlugAdapter

AC adapter

GY-HM150U.book Page III Monday, September 5, 2011 1:48 AM

Introduction

Safety Precautions

(continued)

IMPORTANT (for ownersin the U.K.)

Connection to the mainssupply in the United Kingdom.

DO NOT cut off the mainsplugfrom thisequipment.

If the plug ﬁtted isnot suitable for the power pointsin your

home or the cable istoo short to reach apower point, then

obtain an appropriate safety approved extension lead or

consult your dealer.

BE SURE to replace the fuse only with an identical approved

type, as originally ﬁtted, and to replace the fuse cover.

If nonetheless the mainsplug iscut off be sure to remove

the fuse and dispose of the plug immediately, to avoid

possible shock hazard by inadvertent connection to the

mainssupply.

If thisproduct isnot supplied ﬁtted with amainsplug then

follow the instructionsgiven below:

DO NOT make any connection to the Larger

Terminal coded E or Green.

The wiresin the mainslead are coloured in

accordance with the following code:

Blue to N (Neutral) or Black

Brown to L (Live) or Red

If these coloursdo not correspond with the terminal

identiﬁcationsof your plug, connect as follows:

Blue wire to terminal coded N (Neutral) or coloured black.

Brown wire to terminal coded L (Live) or coloured Red.

If in doubt — consult acompetent electrician.

CAUTIONS:

•To prevent shock, do not open the cabinet. No serviceable

partsinside. Refer servicing to qualiﬁed personnel.

•When youare not using the AC adapter for along period

of time, it isrecommended that youdisconnect the

power cord from AC outlet.

CAUTION:

To avoid electric shock

or damage to the unit,

ﬁrst ﬁrmly insert the

small end of the power

cord into the AC Adapter

until it isno longer

wobbly, and then plug the larger end of the power cord

into an AC outlet.

Products

Battery

Information for Userson Disposal of Old Equipment

and Batteries

Notice:

The sign Pbbelow the symbol

for batteriesindicatesthat this

battery containslead.

[European Union]

These symbolsindicate that the electrical and electronic

equipment and the battery with thissymbol should not be

disposed of as general household waste at itsend-of-life.

Instead, the productsshould be handed over to the

applicable collection pointsfor the recycling of electrical and

electronic equipment as well as batteriesfor proper

treatment, recovery and recycling in accordance with your

national legislation and the Directive 2002/96/EC and

2006/66/EC.

By disposing of these productscorrectly, youwill help to

conserve natural resourcesand will help to prevent potential

negative effectson the environment and human health

which could otherwise be caused by inappropriate waste

handling of these products.

For more information about collection pointsand recycling of

these products, please contact your local municipal office,

your household waste disposal service or the shop where

youpurchased the product.

Penaltiesmay be applicable for incorrect disposal of this

waste, in accordance with national legislation.

(Business users)

If youwish to dispose of thisproduct, please visit our web

page http://www.jvc.euto obtain information about the

take-back of the product.

[Other Countriesoutside the European Union]

These symbolsare only valid in the European Union.

If youwish to dispose of these items, please do so in

accordance with applicable national legislation or other

rulesin your country for the treatment of old electrical and

electronic equipment and batteries.

Dear Customer,

Thisapparatus isin conformance with the valid European

directivesand standardsregarding electromagnetic

compatibility and electrical safety.

European representative of JVC KENWOOD Corporation

is:

JVC Technical ServicesEurope GmbH

Postfach 10 05 04

61145 Friedberg

Germany

diesesGerät stimmt mit den gültigen europäischen

Richtlinien und Normen bezüglich elektromagnetischer

Verträglichkeit und elektrischer Sicherheit überein.

Die europäische Vertretung für die JVC KENWOOD

Corporation ist:

JVC Technical ServicesEurope GmbH

Postfach 10 05 04

61145 Friedberg

Deutschland

Sehr geehrter Kunde, sehr geehrte Kundin,

GY-HM150U.book Page IV Monday, September 5, 2011 1:48 AM

DON’T continuetooperate the equipment if youare in

any doubt about it working normally, or if it isdamaged

in any way — switch off, withdraw the mainsplug and

consult your dealer.

DON’T remove any ﬁxed cover as thismay expose

dangerous voltages.

DON’T

leave equipment switched on when it is

unattended unless it isspeciﬁcally stated that it isdesigned

for unattended operation or has astandby mode. Switch

off using the switch on the equipment and make sure that

your family knowshow to do this. Specialarrangements

may need to be made for inﬁrm or handicapped people.

DON’T

use equipment such as personal stereosor radios

so that youare distracted from the requirementsof road

safety. It isillegal to watch television whilst driving.

DON’T listen to headphonesat high volume, as such

use can permanently damage your hearing.

DON’T

obstruct the ventilation of the equipment, for

example with curtainsor soft furnishings. Overheating

will cause damage and shorten the life of the equipment.

DON’T use makeshift standsand NEVER ﬁx legswith

wood screws— to ensure complete safety alwaysﬁt

the manufacturer’sapproved stand or legswith the

ﬁxingsprovided according to the instructions.

DON’T allow electrical equipment to be exposed to

rain or moisture.

ABOVE ALL

•NEVER let anyone especially children push

anything into holes, slotsor any other opening in the

case — thiscould result in afatal electrical shock;

•

NEVER guess or take chanceswith electricalequipment

of any kind — it isbetter to be safe than sorry!

SOME DO’SAND DON’TSON THE SAFE

USE OF EQUIPMENT

Thisequipment has been designed and manufactured

to meet international safety standardsbut, like any

electrical equipment, care must be taken if youare to

obtain the best resultsand safety isto be assured.

DO read the operating instructionsbefore youattempt

to use the equipment.

DO ensure that all electrical connections(including the

mainsplug, extension leadsand interconnectionsbetween

piecesof equipment) are properly made and in accordance

with the manufacturer’sinstructions. Switch off and withdraw

the mainsplug when making or changing connections.

DO consult your dealer if youare ever in doubtabout

the installation, operation or safety of your equipment.

DO be careful with glass panelsor doorson equipment.

Remember that thiscamcorder isintended for

private consumer use only.

Any commercial use without proper permission

isprohibited. (Even if yourecord an event such

as ashow, performance or exhibition for personal

enjoyment, it isstrongly recommended that you

obtain permission beforehand.)

Trademarks

•

Other product and company namesincluded in

thisinstruction manual are trademarksand/or

registered trademarksof their respective holders.

•

We recommend using the Category 2 HDMI cable

(High Speed cable) for viewing in higher image quality.

•

QuickTime and Final Cut Pro are trademarksof

Apple Inc.

HDMI,the HDMI logo,

and High-Definition MultimediaInterface are

trademarksor registered trademarksof HDMI

Licensing LLC in the United Statesand other

countries.

GY-HM150U.book Page V Monday, September 5, 2011 1:48 AM

Introduction

Precautions for Proper Use . . . . . . . . . . . . . . . . . . . . . . . . . 6

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Attaching the Audio Unit . . . . . . . . . . . . . . . . . . . . . . . .9

Names of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Names of Remote Control Parts and Functions . . . . . . . . 14

Preparations

Settings and Adjustments Before Use . . . . . . . . . . . . . . . . 15

Adjusting the Grip Belt . . . . . . . . . . . . . . . . . . . . . . . . . 15

Setting up the Remote Control . . . . . . . . . . . . . . . . . .15

Attaching an External Microphone . . . . . . . . . . . . . . . .15

Attaching the Tripod . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Removing the Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Lens Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Setting the Clock (Initial Setting) . . . . . . . . . . . . . . . . . . . . 18

Assigning Functions to the [USER] Buttons . . . . . . . . . . . 19

Tally Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

SDHC/SDXC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Inserting an SDHC/SDXC Card . . . . . . . . . . . . . . . . . . 20

Estimated Recordable Time of SDHC/SDXC Cards

. . . . 20

Write-Protect Switch on the SDHC/SDXC Card . . . . . 21

Formatting (Initializing) SDHC/SDXC Cards . . . . . . . . 21

LCD Monitor/Viewfinder . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Viewing the Viewfinder/LCD Screen . . . . . . . . . . . . . .22

Displays on the viewfinder/LCD screen . . . . . . . . . . . . 22

Status Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Auto White Display (Camera Mode Only) . . . . . . . . . . 24

Menu Setting Screen . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Alarm Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Zebra Pattern Display . . . . . . . . . . . . . . . . . . . . . . . . . 24

Shooting

Selecting a Shooting Mode . . . . . . . . . . . . . . . . . . . . . . . .25

Selecting the Full Auto/Manual Shooting Mode . . . . . .25

Selecting a Focusing Mode . . . . . . . . . . . . . . . . . . . . .25

Selecting System Definition, File Format and

Video Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Selecting the Aspect Ratio of SD Videos . . . . . . . . . . .26

Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Viewing Recorded Videos Immediately (Clip Review) . . . .28

Zoom Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Adjusting the Focus Manually . . . . . . . . . . . . . . . . . . . . . .29

Using the Focus Assist Function . . . . . . . . . . . . . . . . .29

Shooting Different Scenes and Conditions (Program AE)

. . .30

Enabling Lolux Mode . . . . . . . . . . . . . . . . . . . . . . . . . .30

Using the Built-in ND Filter . . . . . . . . . . . . . . . . . . . . . . . .30

Adjusting the Exposure Manually . . . . . . . . . . . . . . . . . . .31

Using the Tele Macro Feature . . . . . . . . . . . . . . . . . . . . . .32

Displaying the Zebra Pattern . . . . . . . . . . . . . . . . . . . . . . .32

Displaying the Zebra Pattern . . . . . . . . . . . . . . . . . . . .32

Specifying the Luminance Level Range for

Displaying Zebra Pattern . . . . . . . . . . . . . . . . . . . . . .33

Adjusting the White Balance . . . . . . . . . . . . . . . . . . . . . . .33

Adjusting Automatic White Balance . . . . . . . . . . . . . . .33

Using the Full Auto White Balance (FAW) Function . . .34

Adjusting White Paint . . . . . . . . . . . . . . . . . . . . . . . . . .34

Adjusting Manual Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Adjusting the Shutter Speed . . . . . . . . . . . . . . . . . . . . . . .35

Adjusting the Aperture . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Setting the Photometry Area . . . . . . . . . . . . . . . . . . . . . . .36

Displaying the Color Bars . . . . . . . . . . . . . . . . . . . . . . . . .37

Adjusting the Camera Image . . . . . . . . . . . . . . . . . . . . . . .37

Using the Image Stabilizer . . . . . . . . . . . . . . . . . . . . . . . . .37

Audio Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Setting the Reference Audio Recording Level . . . . . . .38

Using the Built-in Microphone . . . . . . . . . . . . . . . . . . .38

Using an External Microphone Connected to the

[INPUT1/INPUT2] Terminal . . . . . . . . . . . . . . . . . . . .38

Reducing Wind Noise . . . . . . . . . . . . . . . . . . . . . . . . .38

Monitoring Audio Sound Using a Headphone . . . . . . . . . .39

Time Code Recording Setting . . . . . . . . . . . . . . . . . . . . . .39

Displaying the Time Code/User’s Bit . . . . . . . . . . . . . .39

Recording the Time Code . . . . . . . . . . . . . . . . . . . . . .39

Presetting the Time Code/User’s Bit . . . . . . . . . . . . . .40

Presetting the user’s bit . . . . . . . . . . . . . . . . . . . . . . . .40

Protecting Important Scenes (OK Mark Function) . . . . . . .41

Splitting the Clips Freely (Clip Cutter Trig) . . . . . . . . . . . . .41

Dual Rec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Backup Rec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Special Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Pre Rec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Clip Continuous Rec . . . . . . . . . . . . . . . . . . . . . . . . . .45

Frame Rec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Interval Rec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Contents

GY-HM150U.book Page 2 Monday, September 5, 2011 1:48 AM

Playback

Playing Back Recorded Clips . . . . . . . . . . . . . . . . . . . . . . 48

Playing Back Videos from the Thumbnail Screen . . . . 48

Thumbnail Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Thumbnail Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Deleting Clips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Appending and Deleting OK Marks . . . . . . . . . . . . . . . . . . 56

Menu Display and Detailed Settings

Basic Operations in Menu Screen . . . . . . . . . . . . . . . . . . . 58

Display and Description of the Menu Screen . . . . . . . . 58

Text Input with Software Keyboard . . . . . . . . . . . . . . . .59

Menu Screen Hierarchical Chart . . . . . . . . . . . . . . . . . . . . 60

Main Menu Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Record Set Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Record Format Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Rec Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Slot Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Clip Set Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Audio Set Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Camera Function Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Switch Set Item . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Camera Process Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

TC/UB Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

LCD/VF Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Shooting Assist Item . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Marker Setting Item . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Status Display Item . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

A/V Out Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Others Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Media Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Setup File Manage Menu . . . . . . . . . . . . . . . . . . . . . . . . . 75

Adding/Editing Frequently Used Menu Items

(Favorites Menu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Adding Menu Items to Favorites Menu . . . . . . . . . . . .76

Editing Favorites Menu . . . . . . . . . . . . . . . . . . . . . . . . 77

Status Screen

Status Screen in Camera Mode . . . . . . . . . . . . . . . . . . . . 80

Status Screen in Media Mode . . . . . . . . . . . . . . . . . . . . . .85

Camera Features

Marker and Safety Zone Displays . . . . . . . . . . . . . . . . . . .87

Configuring Setup Files . . . . . . . . . . . . . . . . . . . . . . . . . . .87

Saving a Setup File . . . . . . . . . . . . . . . . . . . . . . . . . . .88

Loading a Setup File . . . . . . . . . . . . . . . . . . . . . . . . . .89

Managing/Editing Clips on a PC . . . . . . . . . . . . . . . . . . . .90

When your PC cannot recognize

the SDXC card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90

Viewing Images on a Monitor . . . . . . . . . . . . . . . . . . . . . .91

Wired Remote Control Connection . . . . . . . . . . . . . . . . . .91

Restoring the SDHC/SDXC Card . . . . . . . . . . . . . . . . . . .92

Restoring the SDHC/SDXC Card . . . . . . . . . . . . . . . . .92

Clips Recorded to SDHC/SDXC Cards . . . . . . . . . . . . . . .93

Folders in the SDHC/SDXC Card . . . . . . . . . . . . . . . .93

Clip (Recorded Data) and Clip Name . . . . . . . . . . . . .93

Recorded Clips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93

Others

Error Displays and Actions . . . . . . . . . . . . . . . . . . . . . . . .94

Tally Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98

How to use this manual

Symbols used

Note :Describes precautions concerning the

operation of this product.

Memo :Describes reference information, such as

functions and usage restrictions of this

product.

A:Indicates the reference page numbers and

reference items.

Content of this manual

●

JVC KENWOOD Corporation

Unauthorized duplication or reprinting of this manual, in

whole or in part, is strictly prohibited.

●

Illustrated designs, specifications and other contents of this

manual are subject to change for improvement without

prior notice.

●

Microsoft, Windows, Windows Vista, and Windows 7 are

either registered trademarks or trademarks of Microsoft

Corporation in the United States and/or other countries.

●

Other product and company names included in this

instruction manual are trademarks and/or registered

trademarks of their respective holders. Marks such as

™

and



have been omitted in this manual.

GY-HM150U.book Page 3 Monday, September 5, 2011 1:48 AM

Introduction

This camera recorder enables recording of HD/SD format

images to an SDHC/SDXC card, and also playback of these

images.

New Features [Dual Rec/Backup Rec]

This recorder is equipped with two card slots, a new [Dual

Rec] feature that enables simultaneous recording to both

SDHC/SDXC cards, and another new [Backup Rec] feature

that enables starting/stopping of recording to the two SDHC/

SDXC cards separately.

Backup recording can be performed without any other

equipment.

* Dual Rec: When [Slot Mode] is set to ADualB

( APage 42, 64 )

* Backup Rec: When [Slot Mode] is set to ABackupB

( APage 43, 64 )

New Special Recording Features [Pre Rec/

Frame Rec/Interval Rec]

This recorder is equipped with three special recording

features - [Pre Rec] that enables up to 5 seconds before the

actual recording to be recorded, [Frame Rec] that enables

the specified number of frames to be recorded freely, and

[Interval Rec] that enables the specified number of frames to

be recorded intermittently.

Long-duration Recording using Dual

Media Slots

By loading two SDHC/SDXC cards to the recorder, you can

perform continuous recording or long-duration recording by

recording to the two cards in sequence.

* When [Slot Mode] is set to ASeriesB(APage 64)

SD (Standard Definition) Recording

Supports DV compression of SD images and recording in the

QuickTime or AVI file format.

The use of a wide array of non-linear editing software is also

supported, which helps to ease production of SD videos,

such as DVDs.

Recording in QuickTime (MOV) File Format

Recording can be made in QuickTime (MOV) file format of

Final Cut Pro, a video editing software from Apple Inc.

You can edit the recorded clips directly with Final Cut Pro.

Recording in MP4 File Format

This camera supports recording in the MP4 file format for

NLE systems on Windows, which can be utilized in a wide

range of non-linear editing environments.

Recording on SDHC/SDXC Cards (Class 6/10)

The absence of mechanisms with the use of SDHC/SDXC cards

(Class 6/10) as recording media brings about increased

operation reliability. In addition, the improved compatibility with

PCs enables high-speed data transfer to NLE as well as

reduction of operating costs.

Supports 60 Hz/50 Hz HD Signals

Focus Assist Function

Enables easy and accurate focusing during shooting.

Wide Variety of User Buttons Added

Enables you to switch camera settings instantly to suit the

shooting conditions.

Time Code Reader/Generator

The built-in time code reader/generator can be used to

record and play back the time code and user’s bit.

Built-in Viewfinder and Color LCD Monitor

Displays the status screens, menu screens for settings, and

alarm indications, in addition to the camera image and

playback image.

Built-in Monitor Speaker for Audio Checking

Clip Review Function for Convenient

Recording Review

Camera designed with 3-CCD System for

High-quality Picture

Zebra Pattern Video Level Indication

Full Auto Shooting Mode

Eliminates the need for troublesome switch operations by

automatically providing a wide range of compatibility with

shooting conditions that change as you move between

indoors and outdoors or between bright and dark locations.

Image Stabilizer Feature

Reduces blurring of images due to camera shake.

ND Filter Provided

Program AE Function

Enables selection of shooting conditions according to the

scenes of your preference.

Main Features

GY-HM150U.book Page 4 Monday, September 5, 2011 1:48 AM

White Balance Adjustment Feature

Enables white balance to be adjusted automatically or

manually.

Built-in Color Bars (Multi-format Color

Bars)

Slow Shutter

Makes it possible to brightly shoot video of dark subjects with

little motion by accumulating the images.

Two Audio Input Terminals

This camera recorder comes with two XLR terminals, which

can be used as audio input terminals for the built-in or

external microphone.

Three Video Output Terminals

This camera recorder comes with an HDMI terminal, a

component terminal, and an A/V OUT (video/audio output)

terminal, which support a wide variety of TV monitor types.

Supports Wired Remote Control

Connection to PCs via USB Port

Files stored on an SDHC/SDXC card can be retrieved to a

PC.

Saving and Loading of Setting Files

The current menu and camera recorder settings can be

saved to an SDHC/SDXC card (Up to eight files). In addition,

settings files stored on the SDHC/SDXC card can also be

loaded onto the camera recorder according to the shooting

scene to reproduce the most suitable settings.

Application Software Provided

The [JVC ProHD Clip Manager] application software is

provided for you to copy recorded clips to Windows or

Macintosh PCs and for checking the video images, etc.

(For MP4 file format)

The CD-ROM provided with this camera recorder

comes with [JVC ProHD Clip Manager] and other

application software as well as their user guides.

* For details, refer to the user guides for each application

software.

GY-HM150U.book Page 5 Monday, September 5, 2011 1:48 AM

Introduction

Storage and Usage Locations

Allowable ambient temperature and humidity

Be sure to use this unit within the allowable temperature range of

to 40

and a relative humidity of 30 % to 80 %. Using this

unit at a temperature or humidity outside the allowable ranges could

result not only in malfunction but also serious impact on the CCD

elements as small white spots may be generated. Please exercise

care during use.

Strong electromagnetic waves or magnetism

Noise may appear in the picture or audio and/or the colors may be

incorrect if this unit is used near a radio or television transmitting

antenna, in places where strong magnetic fields are generated by

transformers, motors, etc., or near devices emitting radio waves,

such as transceivers or cellular phones.

Use of wireless microphone near this unit

When a wireless microphone or wireless microphone tuner is used

near this unit during recording, the tuner could pick up noise.

Avoid using or placing this unit in the following places.

•Places subject to extreme heat or cold

•Places with excessive dirt or dust

•Places with high humidity or moisture

•Places subject to smoke or vapor such as near a

cooking stove

•Places subject to strong vibrations or unstable surfaces

•In a parked car under direct sunlight or near a heater for

long hours.

Do not place this unit at places that are subject to

radiation or X-rays, or where corrosive gases occur.

Protect this unit from being splashed with water.

(Especially when shooting in the rain)

Protect this unit from getting wet when shooting on a

beach. In addition, salt and sand may adhere to the body. Be

sure to clean the unit after use.

Protect this unit against penetration of dust when using it

in a place subject to sandy dust.

Do not expose this device and the remote control to

excessive heat, such as direct sunlight or fire. The built-in

battery may explode if it gets heated up.

Do not leave the card slot cover open for a long period of

time. Dirt entering the interior of the slot may cause it to

malfunction.

Transportation

Do not drop or hit this unit against a hard object when

transporting.

Power Saving

When this unit is not in use, be sure to turn off the power

in order to reduce power consumption.

Maintenance

Turn off the power before performing any maintenance.



Wipe the external cabinet of the unit with a soft cloth. Do not

wipe the body with benzene or thinner. Doing so may cause the

surface to melt or turn cloudy. When it is extremely dirty, soak the

cloth in a solution of neutral detergent, wipe the body with it, and

then use a clean cloth to remove the detergent.

Rechargeable Battery

Be sure to use only the specified batteries.

We do not guarantee the safety and performance of this

device if an unspecified battery is used.

The battery is not charged when purchased.

When using the battery in a low temperature environment

(10 for below), the operating time may be shortened, or it

may not function properly. When using the device outdoors in

the winter weather, warm the battery, such as by placing it in

the pocket, before attaching it.

Do not expose the battery to excessive heat, such as

direct sunlight or fire.

If the battery is not to be used for a long time,

use up the charge completely and detach it from the camera

to prevent deterioration.

(Wait for the battery to run out by itself such as through

continuous shooting or playback.)

BCharge the battery once every half a year, and store it

again after using up the charge.

Attach the battery cap after removing the battery, and

store it in a dry place between 15 fto 25 f.

ATTENTION:

The product you have purchased is powered by

a rechargeable battery that is recyclable.

Please call 1-800-8-BATTERY for information

on how to recycle this battery.

Precautions for Proper Use

Battery

Battery Cap

GY-HM150U.book Page 6 Monday, September 5, 2011 1:48 AM

SDHC/SDXC Cards

This camera recorder saves the recorded images and

audio sound on the SDHC/SDXC card (sold separately) in

the card slot.

Use an SDHC/SDXC card (4 GB to 128GB) with Class 6

or higher performance and formatted using this camera

recorder.

* Using cards other than those from Panasonic, TOSHIBA or

SanDisk may result in recording failure or data loss.

If the SDHC/SDXC card contains files recorded by

devices other than this camera recorder or files that are

saved from a PC, the recordable time may be shorter or data

may not be properly recorded. In addition, the remaining

space on the card may not increase even when files are

deleted using a PC.

Handling of SDHC/SDXC Cards

The access lamp and status indicator blink in green when

data on the SDHC/SDXC card is being accessed. Do not

remove the SDHC/SDXC card during data access (such as

recording, playback, or formatting). Do not turn off the power

or remove the battery and AC adapter during access either.

Do not use or store the SDHC/SDXC card in a place that

is subject to static electricity or electrical noise.

Do not place the SDHC/SDXC card near locations that

are exposed to strong magnetic fields or radio waves.

Inserting the SDHC/SDXC card incorrectly may result in

damage of this unit or the SDHC/SDXC card.

We are not liable for any accidental loss of data stored on

the SDHC/SDXC card. Please back up any important data.

Make use of the SDHC/SDXC card within the prescribed

conditions of use.

Do not use it at the following locations.

Places that are subject to direct sunlight, high humidity or

corrosion, places near thermal equipment, sandy or dusty

places, or in a car under the sun with the doors and windows

closed.

Do not bend or drop the SDHC/SDXC card, or subject it to

strong impact or vibration.

Do not splash the SDHC/SDXC card with water.

Do not dismantle or modify the SDHC/SDXC card.

Do not touch the terminals with your hands or with a metal

object.

Do not allow dust, dirt, water, or foreign objects to adhere

to the terminals.

Do not remove the labels or stick other labels or stickers

on the SDHC/SDXC cards.

Do not use pencils or ballpoint pens to write on the SDHC/

SDXC cards. Always use oil-based pens.

If you format (initialize) the SDHC/SDXC card, all data

recorded on the card, including video data and setup files,

will be deleted.

If you want to wipe out all information by completely

erasing the data, we recommend either using commercially

available software that is specially designed for that purpose,

or by physically destroying the SDHC/SDXC card with a

hammer, etc. When formatting or erasing data using the

camera recorder, only the file administration information is

changed. The data is not completely erased from the SDHC/

SDXC card.

Some commercially available SDHC/SDXC cards may be

harder to be removed from this unit. Remove them by

hooking onto the groove on the cards.

●

It will be easier to remove the cards after serveral times.

●

Do not stick any stickers on the cards.

The SDHC/SDXC card may pop out when it is being

removed. Be careful not to lose the card.

Groove

GY-HM150U.book Page 7 Monday, September 5, 2011 1:48 AM

Introduction

Others

Do not insert objects other than the memory card into the

card slot.

Do not turn off the power or remove the power cable

during recording or playback.

The camera recorder may not show stable pictures for a

few seconds immediately after the power is turned on, but

this is not a malfunction.

Do not drop this unit or subject it to strong impact or

vibration as it is a precision equipment.

Optical performance of lens

Due to the optical performance of the lens, color divergence

phenomena (magnification chromatic aberration) may occur

at the periphery of the image. This is not a camera

malfunction.

Noise may appear in the image when switching modes.

If placed on its side, heat release efficiency will

deteriorate.

Use the supplied AC adapter as the power supply. Do not

use the supplied AC adapter on other devices.

When the connectors that come with connector covers are

not in use, put on the covers to prevent damage to the

connectors.

LCD Monitor and Viewfinder

The LCD monitor and viewfinder screens are

manufactured using high-precision technology. Black spots

may appear on the LCD monitor and viewfinder screens, or

red, blue, and/or white spots may not disappear. However,

this is not a malfunction and these spots are not recorded on

the SDHC/SDXC card.

If you use this unit continuously for a long period of time,

the characters displayed in the viewfinder may temporarily

remain on the screen. This is not recorded on the SDHC/

SDXC card. They will not appear after you turn the power off

and then on again.

If you use this unit in a cold place, the images may appear

to lag on the screen, but this is not a malfunction. Retained

images are not recorded on the SDHC/SDXC card.

Do not press against the surface with force or subject it to

strong impact. Doing so may damage or break the screens.

Due to the characteristic of the viewfinder display device,

colors may appear on the images when you blink your eyes.

This is not a malfunction. It does not affect the recorded

images, HDMI output, or component output.

Characteristic CCD Phenomena

Smear and blooming

Due to the physical structure of CCDs, vertical streaking

(called “smear”) may occur when shooting an extremely

bright light source or expansion of light (called “blooming”)

may appear around it. Although the CCD employed in this

unit produces very little smear or blooming, these

phenomena may still occur when shooting a bright light

source.

Moire or aliasing

Stripes, lines or other fine patterns may appear jagged when

they are shot.

White dots

High temperatures can cause CCD sensor pixels to produce

white dots in the image. This is especially prominent when

boosting the sensitivity.

This is a characteristic of the charged-coupled device (CCD).

As far as possible, use this unit under conditions where the

temperature of this unit does not increase.

Characteristic Lens Phenomena

When shooting an extremely bright light source, ghosting

may occur. This is a characteristic of the lens and not a

malfunction.

Any recordings made on this camera recorder that are

played back for profit or public preview may infringe on the

rights of the owner of the recordings.

Do not use the recordings for purpose other than personal

enjoyment without prior consent from the owner.

Precautions for Proper Use

(continued)

Smear

Vertical pale streaking appearing at

high luminous object

High luminous object (such as light

bulbs, sun)

Blooming

Blurring in highlight

Monitor Screen

GY-HM150U.book Page 8 Monday, September 5, 2011 1:48 AM

This camera recorder comes bundled with the following

accessories.

Attaching the Audio Unit

The audio unit (with handle) is not attached to the camera

recorder unit when purchased.

Attach the audio unit according to the following procedure.

Attach the audio unit by sliding it all the way into the

shoe on the top of the camera recorder.

2 Turn the screw on the audio unit clockwise to fasten it

fully and securely to the camera recorder.

If the audio unit is not fully and securely tightened, it will be

loose and may drop off from the camera recorder during use.

3 Connect the audio unit cable to the [AUDIO IN]

terminal of the camera recorder.

Memo :

●The clamp on the audio unit is for fixing the microphone

cable and cannot be used to fix the audio unit cable.

(APage 15)

Accessories

AC Adapter

AP-V20M

Battery

BN-VF823U

Remote

Control Unit

CD-ROM Audio Unit

Component Cable AV Cord Power Cord

Battery

Charger

AA-VF8U

Microphone

(U model: 2)

(E model: 4)

Audio Unit

Screw

Shoe Cable

[AUDIO IN] Terminal

Open the cover

Clamp

GY-HM150U.book Page 9 Monday, September 5, 2011 1:48 AM

Introduction

ATally lamp (APage 19)

Tally lamp (

Page 19)

Remote control sensor (

Page 15)

[AWB] Auto White Balance button (

Page 33)

Lens/Lens cover (

Page 18)

Shoe

For mounting separately sold lights and accessories.

Eyepiece focus lever

Lever for adjusting the visibility. It is found on the under side.

Eyepiece

Viewfinder (

Page 22)

[REC/6] Record trigger/User 6 Button (

Page 27)

Button for starting or stopping recording.

You can also use it as a user button by assigning a specific

feature in the menu setting to this button. (APage 19)

Zoom lever (

Page 28)

For zooming to the Tele (T) or Wide (W) end.

Accessory mounting screw hole

Microphone holder (

Page 15)

For mounting an external microphone.

Knob

Knob for locking the microphone in place.

External microphone (

Page 15)

Names of Parts

AWB

REC / 6

MON K

DCE

FGHI



Front Top

GY-HM150U.book Page 10 Monday, September 5, 2011 1:48 AM

ABuilt-in microphone (APage 38)

Lens cover switch (

Page 18)

Manual ring (

Page 28)

[ND FILTER] switch (

Page 30)

Reduces the amount of incident light to 1/10.

Iris dial (

Page 36)

Enables manual aperture adjustment.

[GAIN] Gain switch (

Page 35)

For selecting one of the three sensitivity levels.

[WHT.BAL] White balance selection switch

(

Page 33)

For selecting one of the three types of white balance.

[IRIS A/M] Iris mode selection button (

Page 36)

Switches between manual and automatic iris.

Card slot A status indicator (

Page 20)

Card slot A (

Page 20)

Slot for SDHC/SDXC cards. Open the door to insert the

SDHC/SDXC card.

Card slot B (

Page 20)

Slot for SDHC/SDXC cards. Open the door to insert the

SDHC/SDXC card.

Card slot B status indicator (

Page 20)

[FULL AUTO] Full Auto mode selection button

(

Page 25)

For setting the shooting mode to the Full Auto or Manual

mode.

[AF/MF] Focusing mode selection button (

Page 25)

For setting the focusing mode to the Auto or Manual mode.

[FOCUS/ZOOM] ring switch

For setting the function of the manual ring to focus

(APage 29) or zoom adjustment (APage 28).

[USER2] User 2 button (

Page 19)

A specific feature in the menu setting can be assigned to this

button according to the user’s preference.

[USER1] User 1 button (

Page 19)

A specific feature in the menu setting can be assigned to this

button according to the user’s preference.

[CH-1/CH-2] CH-1/CH-2 recording level adjustment

knob (

Page 38)

For adjusting the audio input level for the CH-1 or CH-2

audio.

[CH1/CH2 AUDIO SELECT] CH-1/CH-2 audio selection

switch (

Page 38)

For setting the method of adjusting the audio recording level

for the CH-1 or CH-2 audio to the Auto or Manual mode.

[AUDIO INPUT 1/2] INPUT1/INPUT2 audio input signal

selection switch (

Page 38)

For selecting the input signal for the [INPUT1] or [INPUT2]

terminal.

[CH-2 INPUT] CH-2 audio input terminal selection

switch (

Page 38)

For selecting whether to input audio signals to CH-2 audio

from the [INPUT1] or [INPUT2] terminal.

Memo :

●[INPUT1] terminal, [INPUT2] terminal: R, Son Page13

CH-2 INPUT CH-1

CH-2

AUDIO INPUT

AUTO MANUAL

USER1

FOCUS

ZOOM

FILTER

OFF

USER2

AF/MF FULL AUTO

AUDIO

SELECT

INPUT1

INPUT2

- LINE -

- MIC -

MIC+48V

INPUT1

INPUT2

GAIN

L-

M-

H-

B-

A-

PRST-

WHT.BAL

IRISA/M

EFGHIJ KL

UT S

LCD Side

GY-HM150U.book Page 11 Monday, September 5, 2011 1:48 AM

Introduction

ALCD cover

[COMPONENT OUT] Component output terminal

(

Page 91)

[A/V OUT] Audio/Video output terminal (

Page 91)

[C.REVIEW/4] Clip Review/User 4 button (

Page 28)

For checking the most recently captured images.

You can also use it as a user button by assigning a specific

feature in the menu setting to this button. (APage 19)

[ZEBRA/5] Zebra/User 5 button (

Page 32)

For displaying or canceling the display of zebra pattern

based on the luminance of the object. You can also use it as

a user button by assigning a specific feature in the menu

setting to this button. (APage 19)

Built-in speaker (

Page 39)

Adjust the volume with the [ADJ./VOL.] knob on the rear.

Memo :

●

The built-in speaker is usable only in the Media mode. Audio

is not output from the built-in speaker during Camera mode.

●

Audio level in the Camera mode and Media mode can be

adjusted separately.

●

When in the Media mode, the volume of the headphone and

speaker are adjusted at the same time.

●The built-in speaker cannot be used when the [HDMI]

terminal, [A/V OUT] terminal, or headphone jack is

connected.

[SLOT SEL] Slot selection button (

Page 25)

For switching the active card slot during shooting and

playback.

[LOLUX/3] Low-light shooting/User 3 button (

Page 19)

For switching the low-light shooting mode ON or OFF.

You can also use it as a user button by assigning a specific

feature in the menu setting to this button. (APage 19)

[DISPLAY] Display button

For switching the displays on the LCD screen and viewfinder.

(APage 20)

[REC] Record trigger button (

Page 27)

Button for starting or stopping recording.

LCD monitor (

Page 20)

[MENU/THUMB] Menu/Thumbnail button

The operation changes according to the status of the camera

recorder.

During Camera mode: Displays the menu screen. Press

again to exit the menu.

During Media mode: During media playback, the thumbnail

screen is displayed.

During thumbnail screen display, the thumbnail menu is

displayed.

Set lever

When in the Camera mode, this lever is used for Program AE

selection and as the zooming lever. (APage 30)

When in the Media mode, this lever is used for clip selection

and playback control. (APage 48)

When the menu screen is displayed, this lever is used for

menu setting. (APage 58)

Bottom

Tripod mounting holes (

Page 15)

Memo :

●To prevent the camera recorder from falling, attach

securely using the rotation prevention hole.

●Use screws with screw length 5 mm and below.

Names of Parts (continued)

CH-2 INPUT CH-1

CH-2

AUDIO INPUT

AUTOMANUAL

AUTO MANUAL

USER1

FOCUS

ZOOM

FILTER

OFF

USER2

AF/MF FULL AUTO

AUDIO

SELECT

INPUT1

INPUT2

- LINE -

- MIC -

MIC+48V

INPUT1

INPUT2

GAIN

L-

M-

H-

B-

A-

PRST-

WHT.BAL

IRISA/M

C.REVIEW/4 ZEBRA/5

SLOT SEL

DISPLAY

COMPONENT

OUT

A / V OUT

LOLUX/3

MENU/

THUMB

REC

FGHI

KLM

LCD Monitor When the LCD cover is opened

Bottom

GY-HM150U.book Page 12 Monday, September 5, 2011 1:48 AM

Rear

A[OIS] Optical Image Stabilizer button (APage 37)

For switching the image stabilizer feature ON or OFF.

[SHUTTER] Shutter Speed button (

Page 35)

Press this button to set the shutter speed manually.

[AE±] Exposure button (

Page 31)

Press this button to set the exposure manually.

[ADJ./VOL.] Adjustment/Volume knob

[ADJ.] : For adjusting the shutter speed (

Page 35) and

exposure (

Page 31).

[VOL.] : Also for adjusting the volume of a headphone

and the built-in speaker. (

Page 39)

Battery mount (

Page 16)

[HDMI] terminal (

Page 91)

[ ] USB terminal (

Page 90)

[DC] input terminal

Battery lock release button (

Page 16)

[REC] Record trigger button (

Page 27)

For starting or stopping recording.

[MEDIA] Media mode indicating lamp (

Page 25)

Lights up in red during the Media mode.

[CAM] Camera mode indicating lamp (

Page 25)

Lights up in red during the Camera mode.

Memo :

●During the USB mode, both the [MEDIA] indicating lamp

Kand [CAM] indicating lamp Lgo out.

[ACCESS] Access indicating lamp

Lights up or blinks during recording or playback.

Grip Belt Side

[STANDBY/ON OFF]/[CAM/MEDIA] Power/Operation

mode selection switch

STANDBY/ON OFF : Turns the power On/Off. (

Page 17)

CAM/MEDIA : Sets this camera recorder to the Camera

or Media mode.

Memo :

●To switch to the Media mode, fix the switch at the [CAM/

MEDIA] position for 1 second or longer.

Grip belt mount (

Page 15)

[ ] Headphone jack (

Page 39)

[REMOTE] Remote terminal (

Page 91)

For connecting a separately sold wired remote control.

[INPUT1] Audio input 1 terminal (

Page 38)

For connecting an XLR microphone.

[INPUT2] Audio input 2 terminal (

Page 38)

For connecting an XLR microphone.

REMOTE

OPEN

REC

PUSH

OIS

SHUTTER

ADJ./ VOL.

ACCESS

CAM

MEDIA

DEFGHI J

N O PQ

Rear Grip Belt Side

GY-HM150U.book Page 13 Monday, September 5, 2011 1:48 AM

Introduction

A[START/STOP] Button

Button for starting or stopping recording.

[ZOOM] Button

Press [T] to zoom in.

Press [W] to zoom out.

[S.SHOT] Button