JVC GZ-MS130AA User manual

ENGLISH
Dear Customer
Thank you for purchasing this
camcorder. Before use, please
read the safety information and
precautions contained in pages 2
and 3 to ensure safe use of this
product.
LYT2031-001B-M
EN
INSTRUCTIONS
CAMCORDER
For more details on the
operations, refer to the
GUIDEBOOK in the
supplied CD-ROM.
GZ-MS130AA
GZ-MS130BAA_AA_IB_ENB.indb 1GZ-MS130BAA_AA_IB_ENB.indb 1 3/19/2009 9:30:46 AM3/19/2009 9:30:46 AM

EN2
Safety Precautions
Caution on Replaceable lithium battery
The battery used in this device may present a fire
or chemical burn hazard if mistreated.
Do not recharge, disassemble, heat above 100°C
or incinerate.
Replace battery with Panasonic (Matsushita
Electric), Sanyo, Sony or Maxell CR2025.
Danger of explosion or Risk of fire if the battery is
incorrectly replaced.
•Dispose of used battery promptly.
•Keep away from children.
•
Do not disassemble and do not dispose of in fire.
When the equipment is installed in a cabinet or on
a shelf, make sure that it has sufficient space on
all sides to allow for ventilation (10 cm or more on
both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a
newspaper, or cloth etc. the heat may not be able
to get out.)
No naked flame sources, such as lighted candles,
should be placed on the apparatus.
When discarding batteries, environmental
problems must be considered and the local rules
or laws governing the disposal of these batteries
must be followed strictly.
The apparatus shall not be exposed to dripping
or splashing.
Do not use this equipment in a bathroom or
places with water.
Also do not place any containers filled with water
or liquids (such as cosmetics or medicines, flower
vases, potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this
equipment, fire or electric shock may be caused.)
CAUTION:
To avoid electric shock
or damage to the
unit, first firmly insert
the small end of the
power cord into the
AC Adapter until it is
no longer wobbly, and
then plug the larger
end of the power cord into an AC outlet.
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
CAUTIONS:
• If you notice smoke or a peculiar smell coming
from the camcorder or AC Adapter, shut it
down and unplug it immediately. Continue using
the camcorder or AC Adapter under these
conditions could lead to fire or electric shock.
Contact your JVC dealer. Do not attempt to
repair the malfunction yourself.
•To prevent shock, do not open the cabinet. No
user serviceable parts inside. Refer servicing to
qualified personnel.
•When you are not using the AC adapter for a
long period of time, it is recommended that you
disconnect the power cord from AC outlet.
•In certain areas, use the conversion plug
depending on the type of your AC wall outlet.
NOTES:
•The rating plate and safety caution are on the
bottom and/or the back of the main unit.
•The serial number plate is on the battery pack
mount.
•The rating information and safety caution of the
AC adapter are on its upper and lower sides.
WARNING:
The battery pack, the camcorder with battery
installed, and the remote control with battery
installed should not be exposed to excessive heat
such as direct sunshine, fire or the Iike.
CAUTION:
The mains plug shall remain readily operable.
GZ-MS130BAA_AA_IB_ENB.indb 2GZ-MS130BAA_AA_IB_ENB.indb 2 3/19/2009 9:30:50 AM3/19/2009 9:30:50 AM

EN3
If this symbol is shown, it is only
valid in the European Union.
Remember that this camcorder is intended for
private consumer use only.
Any commercial use without proper permission
is prohibited. (Even if you record an event such
as a show, performance or exhibition for personal
enjoyment, it is strongly recommended that you obtain
permission beforehand.)
Trademarks
•Manufactured under licence from Dolby
Laboratories. Dolby and double-D symbol are
trademarks of Dolby Laboratories.
•Windows®is either a registered trademark or
trademark of Microsoft Corporation in the United
States and/or other countries.
•Macintosh is a registered trademark of Apple Inc.
•YouTube and the YouTube logo are trademarks
and/or registered trademarks of YouTube LLC.
•iTunes is a trademark of Apple Inc., registered in the
U. S. and other countries.
•
Other product and company names included in this
instruction manual are trademarks and/or registered
trademarks of their respective holders.
Do not point the lens directly into the sun. This
can cause eye injuries, as well as lead to the
malfunctioning of internal circuitry. There is also a
risk of fire or electric shock.
CAUTION!
The following notes concern possible physical
damage to the camcorder and to the user.
Carrying or holding the camcorder by the LCD
monitor can result in dropping the unit, or in a
malfunction.
Do not use a tripod on unsteady or unlevel surfaces.
It could tip over, causing serious damage to the
camcorder.
CAUTION!
Connecting cables (Audio/Video, S-Video, etc.) to
the camcorder and leaving it on top of the TV is
not recommended, as tripping on the cables will
cause the camcorder to fall, resulting in damage.
GZ-MS130BAA_AA_IB_ENB.indb 3GZ-MS130BAA_AA_IB_ENB.indb 3 3/19/2009 9:30:50 AM3/19/2009 9:30:50 AM

EN4
Easy Start Guide
DC
Access lamp
Blinks: Accessing files
The battery pack
is not charged
at the time of
purchase.
AC Adapter
To AC Outlet
(110V to 240V)
Battery Pack
• Do not pull the strap when you open the
fasten. Please use the tab to open it.
• Fasten the strap when you grip the
camcorder.
• When carrying the camcorder, please be
careful not to drop it.
CAUTION
Be sure to use JVC battery packs. If you use any other battery packs besides
JVC battery packs, safety and performance can not be guaranteed.
Grip Adjustment
Adjust the strap and fasten.
Charge the battery before recording
Turn off the camcorder and attach the battery pack.
Power/charge lamp
Blinks: Charging
goes out: Charging finished
Do not remove the
AC adapter, the
battery pack or the
SD card when
the lamp is blinking.
Open the cover
Grip Strap
Fasten
Ta b
GZ-MS130BAA_AA_IB_ENB.indb 4GZ-MS130BAA_AA_IB_ENB.indb 4 3/19/2009 9:30:50 AM3/19/2009 9:30:50 AM

EN5
Date/Time Setting
QOpen the LCD monitor to
turn on the camcorder
RSelect [YES] within
10 seconds
T
Power Button
SSelect [CLOCK SETTING]
•When the message disappears, press the
power button for at least 2 seconds to turn
off the power, and then press it again for at
least 2 seconds.
•Touch the sensors with your finger. The
sensors do not function if you touch them
with your finger nail or with gloves on.
Select the city closest to
the area where you use
the camcorder
USelect [ON] if daylight
saving time is effective.
LCD monitor
SET
SET DATE/TIME!
YES
NO
Slide your finger up and down on
the sensor. Then touch OK.
SET QUIT
CLOCK SETTING
AREA SETTING
SET FOR DAYLIGHT SAVING TIME
SET THE CITY, DATE AND TIME
CLOCK ADJUST
AREA SETTING
SET QUIT
1. 1. 2009 01: 00
R
SET QUIT
SET FOR DAYLIGHT SAVING TIME
SET DAYLIGHT SAVING TIME
OFF
DAYLIGHT SAVING TIME (DST)
1.11.2009 01:00
VSet the date and time
CLOCK SETTING
SAVEQUIT
DATE TIME
GMT+ 0:00
1 11 2009 16 55
Touch sensor: Sets the date and time
}: Moves the cursor to the right
OK: Clock starts
GZ-MS130BAA_AA_IB_ENB.indb 5GZ-MS130BAA_AA_IB_ENB.indb 5 3/19/2009 9:30:50 AM3/19/2009 9:30:50 AM

EN6
Video recording
CAUTION
Before recording an important scene, it is recommended to conduct a trial
recording.
QSlide the mode switch to select !(video) mode
RSelect recording mode
SStart recording
The mode changes
when you press the
button.
0 : 04 : 01
4 h 59 m
[]
M
The auto recording
indicator appears.
4 h 59 m
0 : 04 : 01
[ ]
REC
Remaining space on built-in
memory or SD card
Video
Quality
Record-
standby
Recording
DC
Press the START/
STOP button to start
recording, and press
it again to stop.
PLAY/REC
GZ-MS130BAA_AA_IB_ENB.indb 6GZ-MS130BAA_AA_IB_ENB.indb 6 3/19/2009 9:30:50 AM3/19/2009 9:30:50 AM

EN7
Playing back
QSelect playback mode
The mode changes when
you press the button.
RSelect the desired file
Index screen
SSelect F(Touch OK) Playback screen
CAUTION
Don’t forget to make copies after recording!
•To copy files onto DVD discs (pg. 27)
•To dub files using a VCR/DVD recorder (pg. 34)
•To play back a created DVD disc (pg. 28)
•To edit files on your computer (pg. 29)
LTo perform operations such as forward search or reverse search (pg. 22)
LTo view files on TV (pg. 25)
It is recommended to copy your important recorded data to a DVD or other recording media
for storage. JVC will not be responsible for any lost data.
LASER TOUCH OPERATION
VIDEO PLAYBACK
DIGEST
1/2
LASER TOUCH OPERATION
01. 11. 2009 16:55
PLAY/REC
GZ-MS130BAA_AA_IB_ENB.indb 7GZ-MS130BAA_AA_IB_ENB.indb 7 3/19/2009 9:30:50 AM3/19/2009 9:30:50 AM

EN8
Contents
GETTING STARTED
Index ...................................................... 10
Accessories .......................................... 12
Attaching the core filter................................12
Preparing the Remote Control..................... 12
Indications on LCD Monitor................. 13
Necessary Settings before Use........... 15
Charging the Battery Pack...........................15
Other Settings....................................... 16
Date/Time Setting........................................16
Language Setting ........................................ 17
Tripod Mounting...........................................17
Using an SD Card........................................18
RECORDING/PLAYBACK
Recording Files..................................... 19
Video Recording..........................................19
Still Image Recording .................................. 20
Zooming.......................................................21
LED Light.....................................................21
Checking the Remaining Battery Power......21
Checking the Remaining Space on the
recording medium ...................................... 21
Playing Back Files ................................ 22
Video Playback............................................22
Still Image Playback ....................................23
Manual Recording ............................... 24
Change to Manual Recording Mode............ 24
Backlight Compensation..............................24
Manual Setting Menu...................................24
USING WITH TV
Viewing Files on TV .............................. 25
Connection with TV...................................... 25
Playback Operation ..................................... 25
EDITING
Managing Files...................................... 26
Capture a Still Image from a Video.............. 26
Deleting Files...............................................26
COPYING
Copying Files ........................................ 27
Using a DVD Burner ....................................27
Creating a DVD using a PC.........................29
Dubbing Files to a VCR/DVD Recorder.......34
Dubbing Files to a VCR/DVD Rlayer............34
Using with a Portable Media Player .... 35
Turning on the Export Mode ........................35
Changing the Export Setting ....................... 35
Transfering the Files to PC ..........................35
Uploading Files to Websites................ 36
Turning on the Upload Mode .......................36
Uploading Files............................................36
FURTHER INFORMATION
Changing the Menu Settings ............... 37
Troubleshooting.................................... 37
Warning Indications ............................. 39
Specifications ....................................... 40
Cautions ................................................ 42
Terms..................................................... 44
GZ-MS130BAA_AA_IB_ENB.indb 8GZ-MS130BAA_AA_IB_ENB.indb 8 3/19/2009 9:30:50 AM3/19/2009 9:30:50 AM

EN9
GETTING
STARTED
RECORDING/
PLAYBACK
USING WITH
TV EDITING COPYING
FURTHER
INFORMATION
How to use the Touch
Sensor
Read these INSTRUCTIONS
to enjoy your CAMCORDER.
For more details on the
operations, refer to the
GUIDEBOOK in the supplied
CD-ROM.
In order to view the
GUIDEBOOK, Adobe®Acrobat®ReaderTM or
Adobe®Reader®must be installed.
Adobe®Reader®can be loaded from Adobe’s
web site:
http://www.adobe.com/
NOTE
Select your desired language with a single
click.
The model name is indicated on the bottom of your
camcorder.
Make a backup of important recorded data
It is recommended to copy your important
recorded data to a DVD or other recording
media for storage. JVC will not be responsible
for any lost data.
Make a trial recording
Before the actual recording of important data,
make a trial recording and play back the
recorded data to check that the video and sound
have been recorded correctly.
Reset the camcorder if it does not operate
correctly
Close the LCD monitor and remove the power
supply (battery pack or AC adapter) from the
camcorder, then reattach it.
Precautions on handling batteries
•Be sure to use the JVC BN-VF808U/VF815U/
VF823U battery packs. This product includes
patented and other proprietary technology and
is made to be used with the JVC battery and
not with other batteries. JVC cannot guarantee
safety or performance of this product when it
is operated by other batteries.
•If the camcorder is subjected to electrostatic
discharge, turn off the power before using it
again.
If a malfunction occurs, stop using the
camcorder immediately and consult your
nearest JVC dealer
• If a problem occurs when using the SD card,
take the card together with the camcorder
for repair. If one of them is not included,
the cause of the malfunction cannot be
diagnosed, and the camcorder cannot be
repaired.
• Recorded data may be erased while the
camcorder is being repaired or inspected.
Back up all data before requesting repairs or
inspections
Because camcorder may be used for
demonstration in a shop, the demonstration
mode is set to on by default
To deactivate the demonstration mode, set
[DEMO MODE] to [OFF].
When Using an SD Card
•Operations are confirmed on the following
SD cards. Class 4 or higher compatible SD or
SDHC card Panasonic, TOSHIBA, SanDisk,
ATP SD card (256 MB to 2 GB) or SDHC card
(4 GB to 32 GB)
•If other media are used, they may fail to
record data correctly, or they may lose data
that had already been recorded.
•MultiMediaCards are not supported.
Read This First!
After the menu is displayed on the LCD monitor:
MANUAL SETTING
LIGHT
REGISTER EVENT
VIDEO QUALITY
USE DETAIL SETTINGSBASED
SET QUIT
VIDEO
QSlide your finger up and down on the sensor.
RSelect [SET]. (Touch OK.)
A
B
ATo select an on-screen button appearing on
the left side, touch the portion of the sensor
next to the on-screen button.
BTo select an on-screen button appearing at
the bottom of the screen, touch the buttons
underneath them.
GZ-MS130BAA_AA_IB_ENB.indb 9GZ-MS130BAA_AA_IB_ENB.indb 9 3/19/2009 9:30:51 AM3/19/2009 9:30:51 AM

EN10
Index
DC
NOTE
•The LCD monitor can rotate 270°.
•Be careful not to cover 4, 5, 7and 8
during shooting.
GETTING STARTED
GZ-MS130BAA_AA_IB_ENB.indb 10GZ-MS130BAA_AA_IB_ENB.indb 10 3/19/2009 9:30:51 AM3/19/2009 9:30:51 AM

EN11
GETTING
STARTED
Camcorder
!Touch Sensor
#OK Button
$MENU Button
%Power (1) Button
&SD Card Slot (pg. 18)
(EXPORT Button
)AV Connector
*UPLOAD Button (pg. 36)
+PLAY/REC Button (pg. 19, 20, 22, 23)
,Mode Switch [!, #]
-DIRECT DVD Button (pg. 28)
INFO Button (pg. 21)
.START/STOP Button (pg. 19)
/SNAPSHOT Button (pg. 20)
0Zoom Lever [W 7,T] ( pg. 21)
Speaker Volume Control
1Speaker
2DC Connector
3USB Connector (pg. 27, 30)
4Camera Sensor
5LED Light (pg. 21)
6Lens Cover
7Lens
8Stereo Microphone
9Stud Hole
:Tripod Mounting Socket (pg. 17)
;Battery Release Button [BATT.] (pg. 15)
Remote Control
QInfrared Beam Transmitting Window
RZOOM (T/W) Buttons (Zoom in/out)
SUp Button
TSkip Backward Button
ULeft Button
VBack Button
WPLAYLIST Button
XSTART/STOP Button
YS. SHOT (SNAPSHOT) Button
ZINFO Button
aSkip Forward Button
bPLAY/PAUSE/SET Button
cRight Button
dNext Button
eDown Button
fINDEX Button*
gDISP Button
* Each time you press INDEX, the screen
switches as shown below:
!mode:
Index Screen «Group Index Screen
#mode:
Index Screen «Date Index Screen
GZ-MS130BAA_AA_IB_ENB.indb 11GZ-MS130BAA_AA_IB_ENB.indb 11 3/19/2009 9:30:51 AM3/19/2009 9:30:51 AM

EN12
Accessories
AC Adapter
AP-V20M
Battery Pack
BN-VF808U
Audio/Video
Cable
Power cord Remote Control
RM-V751U
USB Cable CD-ROM Core Filter (x2) Lithium Battery
CR2025
Pre-installed in the
remote control unit.
NOTE
Make sure to use the provided cables for connections. Do not use any other cables.
Attaching the Core Filter
The core filter reduces interference caused when connecting to other devices.
Preparing the Remote Control
A battery is included inside the remote control at the time of purchase.
Remove the insulation sheet before use.
Release the stopper. 3 cm USB Cable: Wind once
AC Adapter: Wind twice
Beam Effective Area
NOTE
The transmitted beam may not be effective
or may cause incorrect operation when the
remote sensor is directly exposed to sunlight
or powerful lighting.
To Reinsert the Battery
Pull out the battery holder by pressing the
lock tab.
Lock Tab
Lithium Battery
(CR2025)
Effective distance:
5 m
Remote Sensor
To be connected
to the camcorder
GZ-MS130BAA_AA_IB_ENB.indb 12GZ-MS130BAA_AA_IB_ENB.indb 12 3/19/2009 9:30:51 AM3/19/2009 9:30:51 AM

EN13
GETTING
STARTED
During Video Recording Only
REC
0:04:01
[4h59m]
PHOTO
LIB.
!Mode Indicator
#EXPORT Mode Indicator (pg. 35)
$Counter
%Upload Mode Indicator ( pg. 36)
A: Analog Input Indicator
&Video Quality:
B(ULTRA FINE), C(FINE),
D(NORMAL), E(ECONOMY)
(Remaining Time
)MREC: (Appears during recording.)
MQ: (Appears during record-standby mode.)
*Digital Image Stabilizer (DIS) Indicator
(Appears when [DIS] is set to [OFF].)
+Auto switch record media
,Shooting Indicator (pg. 19)
-Wind Cut Indicator
.Event Indicator
During Still Image Recording Only
[9999]
FIN E
10
PHOTO
!Mode Indicator
#Focus Indicator ( pg. 20)
$Image Quality: FINE (fine) or STD
(standard)
%Remaining Number of Shots
&Shooting Indicator ( pg. 20)
(Shutter Mode Indicator
)Self-Timer Indicator
Indications on LCD Monitor
During both Video and Still Image
Recording
WT
0
1/4000
LCD
16:551. 11. 2009
SD
!Selected Operation Mode Indicator
( pg. 24)
4: Auto Mode
3: Manual Mode
#Effect Mode Indicator
$Tele Macro Mode Indicator
%LED Light Indicator ( pg. 21)
&Scene Select Mode Indicator
(Quick Review Indicator (pg.19, 20)
)Zoom Indicator ( pg. 21)
*Recording Medium Indicator
SD
: SD Card
: Built-in memory
+White Balance Indicator
,Monitor Backlight Indicator
-Battery Indicator
.Date/Time ( pg. 16)
/Manual Focus Adjustment Indicator
0Backlight Compensation Indicator
( pg. 24)
1Brightness Control Indicator
.: Photometry Area Control Indicator
2Shutter Speed
GZ-MS130BAA_AA_IB_ENB.indb 13GZ-MS130BAA_AA_IB_ENB.indb 13 3/19/2009 9:30:51 AM3/19/2009 9:30:51 AM

EN14
During Video Playback
+4
8
SD
1: 55 : 01
16:551. 11. 2009
!Mode Indicator
#Playlist Playback Indicator (Appears when
playing back a playlist.)
$Video Quality:
B(ULTRA FINE), C(FINE),
D(NORMAL), E(ECONOMY)
%Counter
&Playback Mode
F: Playback
Q: Pause
K: Forward Search
J: Reverse Search
G: Forward Slow-Motion
E: Reverse Slow-Motion
(The number on the left shows speed.)
(Battery Indicator
)Date/Time ( pg. 16)
*Volume Level Indicator
During Still Image Playback
SD
101- 0098
16:551. 11. 2009
!Mode Indicator
#Folder/File Number
$Slide Show Playback Indicator
%Battery Indicator
&Date/Time ( pg. 16)
Indications on LCD Monitor (Continued)
GZ-MS130BAA_AA_IB_ENB.indb 14GZ-MS130BAA_AA_IB_ENB.indb 14 3/19/2009 9:30:52 AM3/19/2009 9:30:52 AM

EN15
GETTING
STARTED
Charging the Battery Pack
1Close the LCD monitor to turn off the
camcorder.
2Attach the battery pack, then
connect the AC adapter.
• With the “vv” (arrow) on the battery pack
pointing at the correct direction, slide the
battery pack until it locks in place.
DC
• Connect the power cord to the AC adapter,
and plug the power cord into an AC outlet.
•The power/charge lamp blinks to indicate
charging has started.
•When the lamp goes out, charging is
finished.
LTo check the remaining battery power
See page 21.
LRequired charging/recording time
(approx.)
*When the LED light is off and the monitor
backlight is set to [STANDARD] mode.
Battery pack Charging time Recording time
BN-VF808U
(Provided)
1 hr. 50 min. 2 hr. 45 min.*
BN-VF815U 2 hr. 40 min. 5 hr. 25 min.*
BN-VF823U 3 hr. 40 min. 8 hr. 10 min.*
LTo detach the battery pack
NOTE
•You can also use the camcorder with just
the AC adapter.
•The actual recording time may shorten
depending on the recording environment,
such as when recording scenes with fast
moving subject.
•Please do not pull or bend the AC adapter
plug and cable. This may damage the AC
adapter.
Necessary Settings before Use
DC Jack
AC Adapter
To AC Outlet
(110V to 240V)
vv Arrow
BATT.
GZ-MS130BAA_AA_IB_ENB.indb 15GZ-MS130BAA_AA_IB_ENB.indb 15 3/19/2009 9:30:52 AM3/19/2009 9:30:52 AM

EN16
Date/Time Setting
1Open the LCD monitor to turn on the
camcorder.
2Touch MENU.
3Select [DISPLAY SETTINGS].
CONFIGURE ON-SCREEN DISPLAY
VIDEO
WIND CUT
AUTO SWITCH REC MEDIA
>
>
DISPLAY SETTINGS
>
BASIC SETTINGS
SET QUIT
4Select [CLOCK ADJUST].
DISPLAY SETTINGS
SET DATE AND TIME
LANGUAGE
CLOCK ADJUST
DATE DISPLAY STYLE
MONITOR BRIGHT
SET QUIT
5Select [CLOCK SETTING].
CLOCK ADJUST
SET THE CITY, DATE AND TIME
CLOCK SETTING
AREA SETTING
SET FOR DAYLIGHT SAVING TIME
SET QUIT
6Select the city closest to the area
where you use the camcorder.
AREA SETTING
SET QUIT
1. 11. 2009 16:55
7Select [ON] if daylight saving time is
effective.
[ON]: Clock is advanced one hour from
the normal time which you set.
[OFF]: Deactivates the function.
SET FOR DAYLIGHT SAVING TIME
SET DAYLIGHT SAVING TIME
OFF
DAYLIGHT SAVING TIME (DST)
SET QUIT
1. 11. 2009 16:55
8Set the date and time.
Select the item by using the touch sensor
and select [}] to set.
CLOCK SETTING
DATE TIME
GMT+ 0:00
1112009 1655
SAVEQUIT
9Select [SAVE].
To reset the setting, select [QUIT]
Setting the clock to local time
when traveling
After performing steps 1-4
5Select [AREA SETTING].
CLOCK ADJUST
SET WHEN IN ANOTHER COUNTRY
CLOCK SETTING
SET FOR DAYLIGHT SAVING TIME
SET QUIT
AREA SETTING
6Select the city closest to the area
you are traveling.
AREA SETTING
SET QUIT
1. 11. 2009 16:55
LTo return to the previous screen
Select @.
LTo quit the screen
Select [QUIT].
Selected area is highlighted
Time difference to
GMT
Principal city of
the selected area
Other Settings
GZ-MS130BAA_AA_IB_ENB.indb 16GZ-MS130BAA_AA_IB_ENB.indb 16 3/19/2009 9:30:52 AM3/19/2009 9:30:52 AM

EN17
GETTING
STARTED
Tripod Mounting
Align the camcorder stud hole with the tripod
stud, and the mounting socket with the screw,
and then rotate the camcorder clockwise to
mount it to the tripod.
NOTE
Do not use a tripod on unsteady or unlevel
surfaces. It could tip over, causing serious
damage to the camcorder.
Bottom of the
Camcorder
Language Setting
The language on the display can be changed.
1Open the LCD monitor to turn on the
camcorder.
2Touch MENU.
3Select [DISPLAY SETTINGS].
CONFIGURE ON-SCREEN DISPLAY
VIDEO
WIND CUT
AUTO SWITCH REC MEDIA
>
>
DISPLAY SETTINGS
>
BASIC SETTINGS
SET QUIT
4Select [LANGUAGE].
ON-SCREEN DISPLAY LANGUAGE
DISPLAY SETTINGS
LANGUAGE
CLOCK ADJUST
DATE DISPLAY STYLE
MONITOR BRIGHT
SET QUIT
5Select the desired language.
LTo return to the previous screen
Select @.
LTo quit the screen
Select [QUIT]
GZ-MS130BAA_AA_IB_ENB.indb 17GZ-MS130BAA_AA_IB_ENB.indb 17 3/19/2009 9:30:52 AM3/19/2009 9:30:52 AM

EN18
Using an SD Card
If you want to record to an SD card, the
following operations need to be performed.
•Operations are confirmed on the following
SD cards: Class 4 or higher compatible
SD or SDHC card Panasonic, TOSHIBA,
SanDisk, ATP SD card (256 MB to 2 GB) or
SDHC card (4 GB to 32 GB).
•If other media are used, they may fail to
record data correctly, or they may lose data
that had already been recorded.
•MultiMediaCards are not supported.
•Cards used to record video on this
camcorder cannot be played back on other
devices.
•Some card readers (including internal card
readers in PCs) may not be able to support
SDHC format. If you use an SDHC card for
recording and encounter any reading error,
the card reader you are using might be a
non-SDHC supported device. Please use
the camcorder or other SDHC compatible
devices to access the card.
QInsert an SD card
Preparation:
Press Power (1) button to turn off the
camcorder.
1Open the SD card cover.
2Firmly insert the card with its clipped
edge first.
3Close the SD card cover.
LTo remove an SD card
Push the SD card once.
After the card comes out a little, pull it out.
Clipped Edge
NOTE
•Insert and remove the SD card only while
the power is turned off. Otherwise, data on
the card may be corrupted.
•Do not touch the terminal on the reverse
side of the label.
RChange the recording medium
The camcorder is programmed to record on
the BUILT-IN MEMORY flash when it is
shipped from the factory. You can change the
recording medium to SD card.
Set [REC MEDIA FOR VIDEO] to [SD
CARD) and [REC MEDIA FOR IMAGE]
to [SD].
E
RASE AL
L
D
A
T
A
A
A ON
TT
REC MEDIA FO
R
VIDEO
RE
C
MEDIA F
O
R I
M
A
GE
F
ORM
A
T
A
A
B
UI
L
T
L
L
-IN MEM
T
T
.
F
ORM
A
T SD CARD
A
A
MEMO
R
Y CARD
RR
QUIT
SET
MEDIA SETTINGS
BUILT-IN MEMORY
SD CARD
SFormat an SD card when using it for
the first time
Select [FORMAT SD CARD] to format
the card.
ERASE ALL DATA ON
MEDIA SETTINGS
REC MEDIA FOR VIDEO
REC MEDIA FOR IMAGE
FORMAT BUILT-IN MEM.
FORMAT SD CARD
QUIT
SET
It is recommended to copy your important
recorded data to a DVD or other recording
media for storage. JVC will not be
responsible for any lost data.
Other Settings (Continued)
GZ-MS130BAA_AA_IB_ENB.indb 18GZ-MS130BAA_AA_IB_ENB.indb 18 3/19/2009 9:30:52 AM3/19/2009 9:30:52 AM

EN19
RECORDING/
PLAYBACK
Recording Files
Video Recording
Press the PLAY/REC button to
select recording mode.
PLAY/REC
Press the START/STOP button to
start recording.
[4 h 59 m]
0:00:01 REC
Approximate remaining time
for recording appears.
You can also start/stop recording by
selecting [REC] on the LCD monitor.
(On-screen recording control).
LTo stop recording
Press the START/STOP again.
LTo view the last recorded scene
Select Awhile recording is paused.
Selecting $during playback deletes that
scene.
LTo record a still image during video
recording
Press SNAPSHOT.
LTo change the picture quality
Change the settings in [VIDEO QUALITY].
LTo change the aspect ratio of the image
(16:9/4:3)
Change the settings in [SELECT ASPECT
RATIO].
Slide the mode switch to select
!(video) mode.
NOTE
•The video recording mode is automatically selected when you turn off the camcorder and then on
again.
•If the camcorder is not operated for 5 minutes while the power is on, it turns itself off automatically to
conserve power.
• After recording video for 12 consecutive hours, recording stops automatically.
• A new file will be created for every 4 GB of continuous shooting.
• This camcorder records video in MPEG2 format compliant with SD-VIDEO format. This camcorder is
not compatible with other digital video formats.
RECORDING/PLAYBACK
[4 h 59 m]
0:00:00
SNAPSHOT
GZ-MS130BAA_AA_IB_ENB.indb 19GZ-MS130BAA_AA_IB_ENB.indb 19 3/19/2009 9:30:52 AM3/19/2009 9:30:52 AM

EN20
Recording Files (Continued)
Still Image Recording
Slide the mode switch to select
#(still image) mode.
Press the PLAY/REC button to
select recording mode.
PLAY/REC
Press and hold the SNAPSHOT
button halfway.
FINE
The ?indicator becomes green when
the captured image is focused.
Press the SNAPSHOT button fully
to take the photo/picture.
FINE [9999]
PHOTO
NOTE
•DIS (Digital Image Stabilizer) does not function during still image recording.
•If the camcorder is not operated for 5 minutes while the power is on, it turns itself off automatically to
conserve power.
LTo view the last recorded image
Select Aafter shooting.
Selecting $during playback deletes
that image.
LTo change the picture quality
Change the settings in [IMAGE
QUALITY].
LTo record still images continuously
Set to [CONTINUOUS SHOOTING] in
[SHUTTER MODE].
FINE [9999]
GZ-MS130BAA_AA_IB_ENB.indb 20GZ-MS130BAA_AA_IB_ENB.indb 20 3/19/2009 9:30:52 AM3/19/2009 9:30:52 AM