JVC KD-DV5000 User manual

ENGLISH
DEUTSCH
FRANÇAIS
LVT1054-001B
[E]
INSTRUCTIONS
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
GEBRUIKSAANWIJZING
NEDERLANDS
DVD/CD RECEIVER
DVD-/CD-RECEIVER
RECEPTEUR DVD/CD
DVD/CD-RECEIVER
KD-DV5000
For installation and connections, refer to the separate manual.
Angaben zu Einbau und Verkabelung entnehmen Sie bitte der gesonderten Anleitung.
Pour l’installation et les raccordements, se référer au manuel séparé.
Zie de afzonderlijke handleiding voor details aangaande het installeren en verbinden van het
toestel.
This unit is equipped with the display demonstration. To cancel it, see page 9.
Dieses Gerät ist mit einer Demonstrationsfunktion für das Display ausgestattet. Auf
Seite 9 wird beschrieben, wie Sie diese Demonstrationsfunktion deaktivieren können.
Cet appareil est équipé d’une démonstration des affichages. Pour l’annuler, référez-
vous à la page 9.
Dit toestel heeft een display-demonstratiefunctie. Zie bladzijde 9 voor het annuleren
van deze functie.
Detachable
COMPACT
DIGITAL VIDEO
KD-DV5000
50Wx4
3 4 5 6 T/P21 D
SRC
DISP
ATT
SEL
MODE
M
+
TOP
MENU
REPEAT
RETURN
INTRORANDOM
OSD EQS ZOOM
SETUP
SEL
CH
AM
FM
DVD
–
RI
SUBTITLEAUDIO ANGLE
+10 010
897
2ndVOL
2ndVOL 564
23
1
DISC
ENTER
MENU
FOLDER
PRESET
DAB
ATT
SHIFT
DUAL
ZONE
+
DISC –
Cover_DV5000[E]f.p65 03.4.13, 14:383

2
ENGLISH
How to reset your unit
After detaching the control panel, press the reset button on the panel holder using a ball-point pen
or similar tool. This will reset the built-in microcomputer.
NOTE:
If you reset the unit during play, the playback mode selections
(e.g. repeat play mode setting), you have selected for the
current disc will be reset to the initial settings.
• During DVD playback, the disc menu selection will also be
reset to the initial disc settings.
Position And Reproduction Of Labels
Name/Rating plate
Bottom panel of the main unit
IMPORTANT FOR LASER PRODUCTS
Precautions:
1.CLASS 1 LASER PRODUCT
2.CAUTION: Invisible laser radiation when open and
interlock failed or defeated. Avoid direct exposure to
beam.
3.CAUTION: Do not open the top cover. There are no
user-serviceable parts inside. Leave all servicing to
qualified service personnel.
4.CAUTION: This DVD/CD player uses invisible laser
radiation and is equipped with safety switches to
prevent radiation emission when unloading CDs. It is
dangerous to defeat the safety switches.
5.CAUTION: Use of controls, adjustments or performance
of procedures other than those specified herein may
result in hazardous radiation exposure.
Note:
For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on
the unit’s chassis. Keep the card in a safe place, as it will help the authorities to identify your unit if stolen.
Caution:
This product contains a laser component
of higher laser class than Class 1.
CLASS
LASER
1
PRODUCT
CAUTION: Invisible laser
radiation when open and
interlock failedor defeated.
AVOIDDIRECT EXPOSURE
TO BEAM. (e)
ADVARSEL: Usynlig laser-
stråling ved åbning, når
sikkerhedsafbrydere er ude
af funktion. Undgåudsæt-
telse for stråling. (d)
VARNING: Osynlig laser-
strålning när denna del är
öppnad och spärren är
urkopplad. Betrakta ej
strålen. (s)
VARO: Avattaessa ja
suojalukitus ohitettaessa
olet alttiina näkymättö-
mälle lasersäteilylle.
Älä katso säteeseen. (f)
EN02-04DV5000[E]f.p65 03.3.23, 18:452

3
ENGLISH
WARNINGS
• DO NOT install any unit in locations where;
– it may obstruct the steering wheel and
gearshift lever operations, as this may result
in a traffic accident.
– it may obstruct the operation of safety
devices such as air bags, as this may result
in a fatal accident.
– it may obstruct visibility.
• DO NOT operate any unit while manipulating
the steering wheel, as this may result in a
traffic accident.
• The driver must not watch the monitor while
driving.
If the driver watches the monitor while driving,
it may lead to carelessness and cause an
accident.
• The driver must not put on the headphones
while driving. It is dangerous to shut off the
outside sounds while driving.
• If you need to operate the unit while driving,
be sure to look ahead carefully or you may be
involved in a traffic accident.
• If the parking brake is not engaged, “DRIVER
MUST NOT WATCH THE MONITOR WHILE
DRIVING.” appears on the monitor, and no
playback picture will be shown.
– This warning appears only when the parking
brake wire is connected to the parking brake
system built in the car (refer to the
Installation/Connection Manual).
CAUTION: DO NOT insert a disc while the
disc loading lamp is flashing or is not lit.
(See page 26.)
BEFORE USE
* For safety....
•Do not raise the volume level too much, as this
will block outside sounds, making driving
dangerous.
•Stop the car before performing any complicated
operations.
* Temperature inside the car....
If you have parked the car for a long time in hot
or cold weather, wait until the temperature in the
car becomes normal before operating the unit.
Caution:
If the temperature inside the car is below 0°C, the
movement of animation and text scroll will be
halted on the display to prevent the display from
being blurred. (LOW TEMP.) indicator
appears on the display.
When the temperature increases, and the operating
temperature is resumed, these functions will start
working again.
CAUTION on Volume Setting:
Discs produce very little noise compared with
other sources. If the volume level is adjusted for
the tuner, for example, the speakers may be
damaged by the sudden increase in the output
level. Therefore, lower the volume before playing a
disc and adjust it as required during playback.
Thank you for purchasing a JVC product. Please read all instructions carefully before operation,
to ensure your complete understanding and to obtain the best possible performance from the unit.
This product incorporates copyright protection
technology that is protected by method claims
of certain U.S. patents and other intellectual
property rights owned by Macrovision
Corporation and other rights owners. Use of
this copyright protection technology must be
authorized by Macrovision Corporation, and is
intended for home and other limited viewing
use only unless otherwise authorized by
Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
EN02-04DV5000[E]f.p65 03.3.23, 18:453

4
ENGLISH
CONTENTS
How to reset your unit ............................... 2
LOCATION OF THE BUTTONS ............ 5
Control panel ............................................. 5
Remote controller ...................................... 6
Preparing the remote controller ................ 7
BASIC OPERATIONS ....................... 8
Turning on the power ................................ 8
Canceling the display demonstration ........ 9
Setting the clock ........................................ 9
Activating the level meter .......................... 10
RADIO OPERATIONS ...................... 11
Listening to the radio ................................. 11
Storing stations in memory ....................... 13
Tuning in to a preset station ...................... 15
Changing the display pattern .................... 16
RDS OPERATIONS ......................... 17
What you can do with RDS ....................... 17
Other convenient RDS functions and
adjustments ............................................ 22
PLAYABLE DISCS .......................... 24
BASIC DISC PLAYBACK ................... 26
Starting playback ...................................... 26
Locating a particular title/chapter/track ..... 28
Locating a particular folder ........................ 29
DVD/VCD SPECIAL FUNCTIONS ......... 30
Selecting subtitles ..................................... 30
Selecting audio languages ........................ 30
Selecting multi-angle views ....................... 31
Menu operations ....................................... 31
Zoom in ..................................................... 32
ADVANCED DISC OPERATIONS .......... 33
Searching for a particular point ................. 33
Playing in various play modes .................. 35
OSD DISC OPERATIONS .................. 37
Operations on the monitor screen ............. 37
DUAL ZONE OPERATIONS ................ 40
Listening with headphones ....................... 40
OTHER DISC OPERATIONS ............... 42
Basic disc playback ................................... 42
Locating a title/chapter/track on a disc ...... 43
Selecting a folder/track to play
using the lists .......................................... 44
Selecting playback modes ........................ 45
Prohibiting disc ejection ............................ 48
Changing the display pattern .................... 48
DVD SETUP MENU ......................... 50
Basic setting procedure ............................ 50
SOUND ADJUSTMENTS ................... 54
Adjusting the sound .................................. 54
Selecting preset sound modes
(iEQ: intelligent equalizer) ...................... 55
Storing your own sound adjustments ........ 56
OTHER MAIN FUNCTIONS ................ 57
Changing the general settings (PSM) ....... 57
Selecting the dimmer mode ...................... 61
Changing the display color ........................ 62
Assigning names to the sources ............... 64
Detaching the control panel ...................... 65
CD CHANGER OPERATIONS .............. 66
Playing discs ............................................. 66
Selecting the playback modes .................. 70
EXTERNAL COMPONENT OPERATIONS .... 72
Playing an external component ................. 72
DAB TUNER OPERATIONS ................ 73
Tuning in to an ensemble and one of the
services .................................................. 73
Storing DAB services in memory .............. 74
Tuning in to a preset DAB service ............ 75
What you can do more with DAB .............. 76
Changing the display information .............. 77
ADDITIONAL INFORMATION ............. 78
LANGUAGE CODES ........................ 79
GLOSSARY .................................. 80
TROUBLESHOOTING ...................... 81
MAINTENANCE ............................. 84
Handling discs ........................................... 84
SPECIFICATIONS ........................... 85
EN02-04DV5000[E]f.p65 03.3.23, 18:454

5
ENGLISH
LOCATION OF THE BUTTONS
Control panel
Refer to the pages in parentheses for details.
1SRC (source) button (8, 64, 66, 72, 73)
2•(standby/on/attenuator)
button (8)
•Control dial
3Display window
4Remote sensor
55(up) button
•Functions as the Play button for DVDs and
VCDs.
60(eject) button (28, 42)
74/¢buttons
8(control panel release) button (65)
9SEL (select) button
pNumber buttons
qMODE (M) button
wDISP (D) (display) button
(10, 16, 48, 67, 72, 77)
eT/P (TP/PTY) button (18, 20)
r∞(down) button
•Functions as the Stop button for DVDs and
VCDs.
How to use the MODE (M) button
If you press MODE (M), the unit goes into functions mode. While in functions mode, the number
buttons work as different function buttons.
•The 5/∞buttons also work as +10/–10 buttons after pressing MODE (M).
Ex.: When the source is the tuner
To use these buttons for original functions again after pressing MODE (M), wait for 5 seconds
without pressing any of these buttons until the functions mode is cleared.
•Pressing MODE (M) again also clears the functions mode.
Time countdown indicator
M
MODE
345621
KD-DV5000
50Wx4
3 4 5 6 T/P21 D
SRC
DISP
ATT
SEL
MODE
M
12 4 5 6
3
89w
q
p
7
e r
EN05-07DV5000[E]f.p65 03.3.23, 18:465

6
ENGLISH
Remote controller 3SETUP button (50)*2
4Basic sound setting buttons
SEL, +, and –
• The +/– buttons normally function as the
volume adjustment buttons.
• The +/– buttons also function as the
2ndVOL +/– buttons when pressed with
SHIFT (S) button. (41)
5SHIFT (S) button
6EQ (equalizer) button (55)
• Selects the sound modes (iEQ.)
7SUBTITLE button (30)
8ANGLE button (31)
9AUDIO button (30)
pDisc basic operation buttons (28)
7(stop), 8(pause), 3(play)
qDisc advanced operation/tuner operation
buttons
For disc advanced operations:
• FOLDER (PRESET) 5/ ∞
•4/ ¢(reverse search/forward search)
•1/ ¡(reverse/fast forward): These
buttons do not work for CD changer
operations.
For tuner operations:
• PRESET (FOLDER) 5/ ∞
•4/ ¢
– For FM/AM tuner: Functions to search for
stations.
– For DAB tuner: If pressed and held,
selects DAB ensembles.
If pressed briefly, selects
DAB services.
wTOP MENU button (31)*2
eMENU button (31)*2
rMenu operation buttons*2
Cursor (5/ ∞/ 2/ 3), and ENTER
tRETURN button (31, 32)*2
yPlay mode buttons (35, 36, 70, 71)*2
RANDOM (R), INTRO (I), and REPEAT ( )
uOSD button (37)
iZOOM button (32)
*1Without connecting the DAB tuner or CD changer,
you cannot select it as the source to play.
*2These buttons function as the number buttons
when pressed with SHIFT (S) button.
+
TOP
MENU
RETURN
REPEATINTRORANDOM
OSD EQS ZOOM
SETUP
SEL
CH
AM
FM
DVD
–
RI
SUBTITLEAUDIO ANGLE
2ndVOL
2ndVOL 564
23
1
DISC
ENTER
MENU
FOLDER
PRESET
DAB
ATT
SHIFT
DUAL
ZONE
+
DISC –
+10 010
897
1
2
3
4
5
6
7
8
9
p
q
w
e
r
t
y
u
i
IMPORTANT:
If “Dual Zone” is turned “On” (see page 40),
the remote controller only functions for
operating the DVD/CD player.
Refer to the pages in parentheses for details.
1(standby/on/attenuator) button
2Source selection button
DVD, FM (DAB), AM, and CH
•DVD button also functions as the DUAL
ZONE button while pressed with SHIFT (S)
button. (40)
•FM (DAB) button:
–Functions to switch the FM tuner and the
DAB if pressed and held.*1
–Functions to change the bands in
sequence if pressed.
•CH button does not function if no CD
changer is connected.*1
EN05-07DV5000[E]ff.p65 03.4.24, 13:046

7
ENGLISH
Preparing the remote controller
Before using the remote controller:
•Aim the remote controller directly at the remote
sensor on the main unit. Make sure there is no
obstacle in between.
•Do not expose the remote sensor to strong light
(direct sunlight or artificial lighting).
Installing the battery
When the controllable range or effectiveness of the
remote controller decreases, replace the battery.
1. Remove the battery holder.
1) Push out the battery holder in the direction
indicated by the arrow using a ball-point
pen or a similar tool.
2) Remove the battery holder.
2. Place the battery.
Slide the battery into the holder with the + side
facing upwards so that the battery is fixed in
the holder.
3. Return the battery holder.
Insert again the battery holder pushing it until
you hear a clicking sound.
(back side)
Lithium coin battery
(product number:
CR2025)
(back side)
Remote sensor
WARNING:
• Store the battery in a place where children cannot
reach.
If a child accidentally swallows the battery,
consult a doctor immediately.
• Do not recharge, short, disassemble or heat the
battery or dispose of it in a fire.
Doing any of these things may cause the battery
to give off heat, crack or start a fire.
• Do not leave the battery with other metallic
materials.
Doing this may cause the battery to give off heat,
crack or start a fire.
• When throwing away or saving the battery, wrap
it in tape and insulate; otherwise, the battery may
start to give off heat, crack or start a fire.
• Do not poke the battery with tweezers or similar
tools.
Doing this may cause the battery to give off heat,
crack or start a fire.
CAUTION:
DO NOT leave the remote controller in a place
(such as dashboards) exposed to direct sunlight
for a long time. Otherwise, it may be damaged.
1)
2)
This receiver is equipped with the steering
wheel remote control function.
If your car is equipped with the steering
wheel remote controller, you can operate this
receiver using the controller.
•See the Installation/Connection Manual
(separate volume) for connection to utilize
this function.
5
6T/P
D
DISP
MODE
M
EN05-07DV5000[E]f.p65 03.3.23, 18:467

8
ENGLISH
BASIC OPERATIONS
Turning on the power
1 Turn on the power.
Note on One-Touch Operation:
When you select a source in step 2 below, the
power automatically comes on. You do not have
to press this button to turn on the power.
2 Select the source.
Each time you press the button,
the source changes as follows.
*1Without connecting the DAB tuner or CD
changer, you cannot select it as the source to
play.
*2If a disc is not in the loading slot, you cannot
select “DISC” as the source to play.
*3To select “LINE IN,” select “Line In” for the
“Ext Input” setting on page 60.
3 Adjust the volume.
4 Adjust the sound as you want. (See
pages 54 – 56.)
Note:
While playing a source, you can also show the level
meter on the display. For details, see “Activating the
level meter” on page 10.
To drop the volume in a moment
Press briefly while listening to any
source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.
• If you turn the control dial, you can also restore
the sound.
To turn off the power
Press for more than 1 second.
•If you turn off the power while listening to a
disc, playback will start from where playback
has been stopped previously, next time you
turn on the power.
SRC
Current sound (iEQ) mode (see page 55)
Volume level appears.
*1*2
*3
3 4 5 6 T/P21 D
SRC
DISP
ATT
SEL
MODE
M
1, 3
2
DAB DISC
CD-CH or LINE IN
(CD changer)
TUNER
ATT
ATT
*1
EN08-10DV5000[E]f.p65 03.3.23, 18:478

9
ENGLISH
Canceling the display
demonstration
When shipped from the factory, display
demonstration has been activated, and starts
automatically when no operations are done for
about 20 seconds.
•It is recommended to cancel the demonstration
before you use the unit for the first time.
To cancel the display demonstration, follow
the procedure below:
1 Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see pages 58 and 59.)
2 Press number button 1 to select
“MOVIE”—Movie category of the PSM
settings.
The “Graphics”setting screen appears on
the display.
3 Select “Off.”
4 Finish the setting.
SEL
To activate the display demonstration, repeat
the same procedure and select “Int Demo”or
“All Demo”in step 3 .
•For more details, see “To set the movie
demonstration—Graphics”on page 59.
Setting the clock
You can also set the clock system to 24 hours or
12 hours.
1 Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see pages 58 and 59.)
2 Press number button 2 to select
“CLOCK”—Clock category of the
PSM settings.
The “Clock Hr”setting screen appears on
the display.
3 Adjust the hour.
4 Set the minute.
1Select “Clock Min (minute).”
2Adjust the minute.
SEL
SEL
12
CONTINUED ON THE NEXT PAGE
345621
345621
ATT
ATT
ATT
EN08-10DV5000[E]f.p65 03.3.23, 18:479

10
ENGLISH
5 Set the clock system.
1Select “24H/12H.”
2Adjust “24Hours”or “12Hours.”
6 Finish the setting.
To check the current clock time when the unit
is turned off, press DISP (D).
The power turns on and the clock time is shown
for about 5 seconds, then the power turns off.
Activating the level meter
You can show the level meters on the display
while playing any source. This unit is equipped
with three level meter patterns.
•There is a time limit in doing the following
procedure. If the setting is canceled before you
finish, start from step 1 again.
1 Press SEL (select) repeatedly until
“METER”selection screen appears
on the display.
Last selected level meter
appears on the display.
Each time you press the button,
the adjustable items change as
follows:
•For iEQ (sound mode) settings, see pages
55 and 56.
•For SEL (basic sound) settings, see page
54.
12
SEL
Off 1
2
3
Meter 1:
The audio level meter fluctuates vertically.
Meter 2:
The speaker on the display vibrates as input
audio level changes.
Meter 3:
The left and right audio level meters appear.
•If the display pattern is changed, only one
audio level meter will be shown.
Off:
No level meter is shown. The source animation
appears.
NOTICE:
The illustrations of the display used in this manual
are mainly of the initial setting when shipped from
the factory. If you have changed the display
patterns or some PSM items, the actual displays
you see will be different.
2 Select the level meter pattern you
want.
As you turn the control
dial, the level meters
change as follows:
SEL
SEL METER
Canceled
iEQ
ATT
ATT
EN08-10DV5000[E]f.p65 03.3.23, 18:4710

11
ENGLISH
RADIO OPERATIONS
Selected band appears.
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
FM1 FM2 FM3 AM
SRC
The operations of this section are mainly
explained using the buttons on the control panel.
When the remote controller can be used for the
same operations, it is then explained.
Listening to the radio
You can use either automatic searching or manual
searching to tune in to a particular station.
Searching for a station automatically:
Auto search
This operation is also possible from the remote
controller.
1 Select the band (FM1 – 3, AM).
1Press SRC (source)
repeatedly to select the tuner.
2Press and hold SRC.
Each time you press and hold
the button, the band changes.
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to an
FM broadcast.
2 Start searching for a station.
When a station comes in, searching stops.
To stop searching before a station is received,
press the same button you have pressed for
searching.
When using the remote controller
1Press FM (DAB) or AM.
• When selecting the FM bands,
press FM (DAB) repeatedly until
the band you want is selected.
2Press ¢or 4to start
searching.
AM
FM
DAB
To search for stations of
higher frequencies
To search for stations of lower
frequencies
3 4 5 6 T/P21 D
SRC
DISP
ATT
SEL
MODE
M
EN11-16DV5000[E]f.p65 03.3.23, 18:4711

12
ENGLISH
FM1 FM2 FM3 AM
SRC
M
MODE
Searching for a station manually:
Manual search
1 Select the band (FM1 –3, AM).
1Press SRC (source)
repeatedly to select the tuner.
2Press and hold SRC.
Each time you press and hold
the button, the band changes.
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
2 Press and hold ¢or 4
until “Manual Search”starts flashing
on the display.
3 Tune in to a station you want while
“Manual Search”is flashing.
•If you release your finger from the button,
the manual mode automatically turns off
after 5 seconds.
•If you hold down the button, the frequency
keeps changing (in 50 kHz intervals for
FM and 9 kHz for AM—MW/LW) until you
release the button.
When an FM stereo broadcast
is hard to receive:
1Press MODE (M) to enter the
functions mode while listening to
an FM stereo broadcast.
“Mode”appears on the display.
2Press number button 1 to select “Mono On”
while “Mode”is still on the display.
Each time you press the button, “Mono On”
and “Mono Off”appears alternately.
When “Mono On”is selected, the MONO indicator
appears, and the sound you hear becomes monaural
but the reception will be improved.
After about
5 seconds
The display returns to the source indication
screen.
345621
See page 40 for this function.
To tune in to stations of
higher frequencies
To tune in to stations of
lower frequencies
EN11-16DV5000[E]f.p65 03.3.23, 18:4712

13
ENGLISH
2Press and hold number button 5 while
“Mode”is still on the display.
Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2, or FM3).
These stations are preset in the number buttons
—No.1 (lowest frequency) to No.6 (highest
frequency).
“–SSM–” appears, then disappears when
automatic preset is over.
Storing stations in memory
You can use one of the following two methods to
store broadcasting stations in memory.
•Automatic preset of FM stations: SSM (Strong-
station Sequential Memory)
•Manual preset of both FM and AM stations
FM station automatic preset: SSM
You can preset 6 local FM stations in each FM
band (FM1, FM2, and FM3).
1 Select the FM band (FM1 –3) you
want to store FM stations into.
1Press SRC (source)
repeatedly to select the tuner.
2Press and hold SRC.
Each time you press and hold
the button, the band changes.
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
2 Start automatic preset.
1Press MODE (M) to enter the functions
mode.
“Mode”appears on the display.
FM1 FM2 FM3 AM
M
MODE
SRC
345621
Then
EN11-16DV5000[E]f.p65 03.3.23, 18:4713

14
ENGLISH
1
3 Press and hold the number button
(in this example, 1) for more than
2 seconds.
4 Repeat the above procedure to store
other stations into other preset
numbers.
Notes:
• A previously preset station is erased when a new
station is stored in the same preset number.
• Preset stations are erased when the power supply to
the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset
the stations again.
To tune in to stations of
higher frequencies
To tune in to stations of
lower frequencies
The display pattern automatically changes like the
above pattern (see page 16). The preset number
flashes for about 5 seconds, then the previous
display pattern resumes.
Manual preset
You can preset up to 6 stations in each band
(FM1, FM2, FM3, and AM) manually.
Ex.: Storing an FM station of 92.5 MHz into the
preset number 1 of the FM1 band.
1 Select the band (FM1 –3, AM) you
want to store stations into (in this
example, FM1).
1Press SRC (source)
repeatedly to select the tuner.
2Press and hold SRC.
Each time you press and hold
the button, the band changes.
2 Tune in to a station (in this example,
of 92.5 MHz).
FM1 FM2 FM3 AM
SRC
EN11-16DV5000[E]f.p65 03.3.23, 18:4714

15
ENGLISH
Selecting a preset station using the
preset station list
If you forget which stations are stored in which
preset numbers, you can check the preset
station list, then select your desired station.
1 Select the band (FM1 –3, AM).
1Press SRC (source)
repeatedly to select the tuner.
2Press and hold SRC.
Each time you press and hold
the button, the band changes.
2 Press and hold 5(up) or ∞(down)
until the preset station list for the
current band (FM1, FM2, FM3, or AM)
appears on the display.
Notes:
• If one of FM band preset station lists (FM1,
FM2, or FM3) is shown on the display, you
can show the other lists by pressing 5(up) or
∞(down).
• If a preset station is an FM RDS station with
PS signal, PS name will be shown instead of
the station frequency.
3 Select the number (1 –6) for the
preset station you want.
FM1 FM2 FM3 AM
345621
SRC
FM1 FM2 FM3 AM
Tuning in to a preset station
You can easily tune in to a preset station.
Remember that you must store stations first. If
you have not stored them yet, see “Storing
stations in memory”on pages 13 and 14.
Selecting a preset station directly
1 Select the band (FM1 –3, AM).
1Press SRC (source)
repeatedly to select the tuner.
2Press and hold SRC.
Each time you press and hold
the button, the band changes.
2 Select the number (1 –6) for the
preset station you want.
When using the remote controller
1Press FM (DAB) or AM.
•When selecting the FM bands,
press FM (DAB) repeatedly
until the band you want is
selected.
2Press the number buttons (1 to 6) while
holding SHIFT (S).
Note:
You can also use the PRESET (FOLDER) 5/ ∞
buttons for selecting a preset station.
345621
SRC
AM
FM
DAB
S
SHIFT
TOP
MENU
564
23
1
DISC
ENTER
MENU
+
EN11-16DV5000[E]f.p65 03.3.23, 18:4715

16
ENGLISH
Changing the display pattern
By pressing DISP (D), you can change the
information shown on the display.
Each time you press the button,
the display patterns change as
follows:
D
DISP
Appears only when
selecting a preset station
number.
Clock time
•When receiving an AM or FM non-RDS
station
•When receiving an FM RDS station
Clock time
PTY code
(see page 23)
PS (station) name
Appears only when
receiving an FM non-RDS
station
EN11-16DV5000[E]ff.p65 03.4.13, 14:4416

17
ENGLISH
RDS OPERATIONS
What you can do with RDS
RDS (Radio Data System) allows FM stations to
send an additional signal along with their regular
programme signals. For example, the stations
send their station names, as well as information
about what type of programme they broadcast,
such as sports or music, etc.
Another advantage of RDS function is called
“Enhanced Other Networks.” By using the
Enhanced Other Networks data sent from a
station, you can tune in to a different station of a
different network broadcasting your favorite
programme or traffic announcement while
listening to another programme or to another
source such as CD.
By receiving the RDS data, this unit can do the
following:
• Tracing the same programme automatically
(Network-Tracking Reception)
• Standby Reception of TA (Traffic
Announcement) or your favorite programme
• PTY (Programme Type) search
• Programme search
• And some other functions
Tracing the same programme
automatically (Network-Tracking
Reception)
When driving in an area where FM reception is
not good, the tuner built in this unit automatically
tunes in to another RDS station, broadcasting the
same programme with stronger signals. So, you
can continue to listen to the same programme in
its finest reception, no matter where you drive.
(See the illustration on page 23.)
Two types of the RDS data are used to make
Network-Tracking Reception work correctly
—PI (Programme Identification) and AF
(Alternative Frequency).
Without receiving these data correctly from the
RDS station you are listening to, Network-
Tracking Reception will not operate.
To use Network-Tracking Reception
You can select the different modes of network-
tracking reception to continue listening to the
same programme in its finest reception.
When shipped from the factory, “AF” is selected.
• AF: Network-Tracking Reception is
activated without Regionalization.
With this setting, the unit switches to
another station within the same
network when the receiving signals
from the current station become
weak. (In this mode, the programme
may differ from the one currently
received.)
The AF indicator lights up.
• AF Reg: Network-Tracking Reception is
activated with Regionalization.
With this setting, the unit switches to
another station, within the same
network, broadcasting the same
programme when the receiving
signals from the current station
become weak.
The REG indicator lights up.
• Off: Network-Tracking Reception is
deactivated.
Neither the AF nor the REG indicator
lights up.
Note:
If a DAB tuner is connected and Alternative Reception
(for DAB services) is activated, Network-Tracking
Reception is also activated (“AF”) automatically. On
the other hand, Network-Tracking Reception cannot
be deactivated without deactivating Alternative
Reception. (See page 76.)
AF or REG indicator lights up.
CONTINUED ON THE NEXT PAGE
EN17-23DV5000[E]f.p65 03.3.23, 18:4817

18
ENGLISH
1 Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see pages 58 and 59.)
2 Press number button 4 to select
“TUNER”—Tuner category of the
PSM settings.
The “PTY Stnby” (standby) setting screen
appears on the display.
3 Select “AF-Regn’l” (alternative
frequency/regionalization
reception).
4 Select the desired mode—“AF,”
“AF Reg,” or “Off.”
5 Finish the setting.
Using TA Standby Reception
TA Standby Reception allows the unit to switch
temporarily to Traffic Announcement (TA) from
the current source (another FM station, CD, or
other connected components).
• TA Standby Reception will not work if you are
listening to an AM station.
Press T/P to activate TA Standby
Reception.
Each time your press the button,
this function is turned on and off
alternately.
7When the current source is FM, the TP
indicator either lights up or flashes.
•If the TP indicator lights up, TA Standby
Reception is activated.
If a station starts broadcasting a traffic
announcement, “Traffic Flash” appears on
the display, and this unit automatically tunes
in to the station. The volume changes to the
preset TA volume level (see page 22) and
the traffic announcement can be heard.
•If the TP indicator flashes, TA Standby
Reception is not yet activated since the
station being received does not provide the
signals used for TA Standby Reception.
To activate TA Standby Reception, you need
to tune in to another station providing these
signals. Press ¢or 4to search
for such a station.
When a station providing these signals is
tuned in, the TP indicator stops flashing and
remains lit. Now TA Standby Reception is
activated.
7When the current source is other than FM,
the TP indicator lights up.
If a station starts broadcasting a traffic
announcement, “Traffic Flash” appears on the
display, and this unit automatically changes the
source and tunes in to the station.
TP indicator (either lights up or flashes)
SEL
345621
SEL
T/P
ATT
EN17-23DV5000[E]f.p65 03.3.23, 18:4818

19
ENGLISH
Using PTY Standby Reception
PTY Standby Reception allows the unit to switch
temporarily to your favorite programme (PTY:
Programme Type) from any source except AM
stations.
To select your favorite PTY code for PTY
Standby Reception
When shipped from factory, PTY Standby
Reception has been set to work for searching for
“News”programmes.
You can select your favorite programme type for
PTY Standby Reception.
1 Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see pages 58 and 59.)
2 Press number button 4 to select
“TUNER”—Tuner category of the
PSM settings.
The “PTY Stnby”(standby) setting screen
appears on the display.
3 Select one of the twenty-nine PTY
codes. (See page 23.)
Selected code name
appears on the display
and is stored into
memory.
4 Finish the setting.
To set PTY Standby Reception
1Press MODE (M) while listening to an FM
stereo broadcast.
“Mode”appears on the display.
2Press number button 3 to activate PTY
Standby Reception while “Mode”is still on the
display.
Each time you press the button, PTY Standby
Reception turns on and off alternately.
The display returns to the source indication
screen.
Ex.: When the currently selected PTY code for
PTY Standby Reception is “News”
PTY indicator (either lights up or flashes)
SEL
345621
SEL
M
MODE
345621
After about
5 seconds
CONTINUED ON THE NEXT PAGE
ATT
EN17-23DV5000[E]f.p65 03.3.23, 18:4819

20
ENGLISH
Searching your favorite programme
You can search any one of the PTY codes.
In addition, you can store your 6 favorite
programme types in the number buttons.
When shipped from the factory, the following
6 programme types have been stored in the
number buttons (1 to 6).
To store your favorite programme types, see
below and page 21.
To search your favorite programme type, see
page 21.
To store your favorite programme types
1 Press and hold T/P for more than 2
seconds while listening to an FM
station.
The last selected PTY code
appears.
2 Select one of the twenty-nine PTY
codes. (See page 23.)
Selected code name
appears on the display.
The PTY indicator either lights up or flashes.
•If the PTY indicator lights up, PTY Standby
Reception is activated.
If a station starts broadcasting the selected
PTY programme, this unit automatically tunes
in to the station.
•If the PTY indicator flashes, PTY Standby
Reception is not yet activated since the station
being received does not provide the signals
used for PTY Standby Reception.
To activate PTY Standby Reception, you need
to tune in to another station providing these
signals. Press ¢or 4to search
for such a station.
When a station providing these signals is tuned
in, the PTY indicator stops flashing and
remains lit. Now PTY Standby Reception is
activated.
Note:
After turning on PTY Standby Reception, you can
change the source without canceling PTY Standby
Reception. In this case, the PTY indicator stops
flashing if it was. If a station starts broadcasting the
selected PTY programme, this unit automatically
changes the source and tunes in to the station.
• If you change the source to AM, PTY Standby
Reception will be temporarily canceled.
• You can only deactivate the PTY Standby Reception
when the source is FM.
Pop M
123
Rock M Easy M
456
Classics Affairs Varied
Ex.: If you have selected “Pop M”previously
T/P
ATT
EN17-23DV5000[E]f.p65 03.3.23, 18:4820