JVC KD-DV7206 Guide

KD-DV7206/KD-DV7205
Installation/Connection Manual
ϰ༬ો˿
GET0375-006A
[U/UT]
0106DTSMDTJEIN
EN, CT
1
ENGLISH
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does
not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
WARNINGS
• DO NOT install any unit in locations where;
– it may obstruct the steering wheel and gearshift lever operations.
– it may obstruct the operation of safety devices such as air bags.
– it may obstruct visibility.
• DO NOT operate the unit while driving.
• If you need to operate the unit while driving, be sure to look ahead carefully.
• The driver must not watch the monitor while driving.
If the parking brake is not engaged, “DRIVER MUST NOT WATCH THE MONITOR WHILE
DRIVING.” appears on the monitor, and no playback picture will be shown.
– This warning appears only when the parking brake wire is connected to the parking brake
system built in the car.
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all
electrical connections before installing the unit.
• Be sure to ground this unit to the car’s chassis again after installation.
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio
dealer.
• It is recommended to connect to the speakers with maximum power of more than 50 W (both at
the rear and at the front, with an impedance of 4to 8 ). If the maximum power is less than
50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 27 of the
INSTRUCTIONS).
• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.
© 2006 Victor Company of Japan, Limited
ՎഠཔçܿᙯϚϯ༫ʹጅ˃ۮçᔃළྐЖڄ࠷çՓӕЉྐཔ௲Ϧé
ëϰ༬ҭ݉આ͵ጆڅϚሉࡍ๙ોгԿԾê
ٍิ!
ëӕۘᎳീӦಗᖃ׆࠷மࡩڄۘᎳീéϨسۘᎳീગጛᖢçቁώJVCԆԾࡖᛏ˜ኀ༿é
ë݈֜ۮಙᑵڄఛʨ᎔ʈᏻʨؠ50 Wçմۇӏ4 ü8 éϨسఛʨʮؠ
50 WçቁቆīAMP GAINĬ׆ࡩçՎಙᑵ๑ᖢéኌ՟·იاڄ୶27ࡗé
ëՎྐഠཔçቁ·ഽሇઘуͶՠΈྐለڄၷʪé
ëʹጅ՟·݈çಞᇊ݃ᇊéϕЏçϚ୰ʹጅçʮ˻ʿ࠱᙮ညಞᇊé
ˁ
ʹጅ෮՟·ڈޠ12 V é࠸ોϚڅྑກԧéϨسڄԾቩԅЉɾྐԦç۱ᄔ࠱ɾࡴྐ
Ꮻ᜵ಗçϚJVCԆԾࡖᛏ˜ኀளකռé
ᙲѿ
• ˞ˢઆ͵ጆϰ༬ϛʔ࠾уí
ý়ҟᗊይіϏᇠ֝᜶௦ᐒଂڅуê
ý়ҟᗊይіϰθ༬èϩϰθឹேയڅуê
ý়ҟᗊං௵څуê
•˞ˢϛኣኡཬധˁይі͵ጆê
•ϛኣኡཬധˁࠝᄕ࠲ይі͵ጆè˞৪࠲ઃ˞ٍิۯê
•ኣኡ࢝ϛኣኡཬധˁ˞ˢߢΖወê
ࠝ˿۬Կͷ⽃ϑèĬኣኡèኣኡ࢝ቂˢߢΖܴêĭϫᆠϛΖወʖè٘ᆒ؟
ྱê
ý෯ັ˿۬ԿዘሉႪԇԿ˗څ˿۬ԿԧߠોАᙲѿےࣦʽê
Heat sink
ಞᇊ
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit
will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in
your car.
ྑກ֝ಚᑶወોሉٍิො!
•˞ˢӖಚᑶወዘሉોᏄોгྑЗèѵ۲͵ጆઆᘸࡍ๒ᖣê
ëϚӕಙᑵለᏃвಙᑵ˃ۮçᐓފԆԾʕڄಙᑵለཔé
Instal1-3_DV7206_006A_pre.indd 1Instal1-3_DV7206_006A_pre.indd 1 1/18/06 9:04:10 AM1/18/06 9:04:10 AM

2
Parts list for installation and connection
If any item is missing, consult your JVC car audio dealer immediately.
M
Battery
ྐЖ
L
Remote controller
ჲ
D
Trim plate
༫ྟ
H
Lock nut (M5)
ᕬ׆ᒘ(M5)
E
Power cord
ྐཔ·ڄለӧ
I
Mounting bolt (M5 ×20 mm)
ႌ֣ᒘ(M5 ×20 mm)
J
Rubber cushion
ጁሗՎ࿑
K
Handles
ػܓӕ˾
G
Washer (ø5)
࿑(ø5)
C
Sleeve
ࢭጅೋ
A/ B
Hard case/Control panel
ഢୢվࡒػ
F
Crimp connector
қʪᏃ
Έءϰ༬֝ોڅྒྷέ
ࠜЉέщྒάးçቁΘո۽༿ڄJVCԆԾࡖᛏኀé
About sounds reproduced through the rear terminals
• Through the analog terminals (Speaker out/LINE OUT/2nd AUDIO OUT):
2-channel signal is emitted.
When playing a multi-channel encoded disc, multi-channel signals are downmixed. (AUDIO—
DOWN MIX: see page 29 of the INSTRUCTIONS.)
• Through DIGITAL OUT (optical):
Digital signals (Linear PCM, Dolby Digital*1, DTS*2, MPEG Audio) are emitted through this terminal.
(For more details, see page 35 of the INSTRUCTIONS.)
To reproduce multi-channel sounds such as Dolby Digital and DTS, connect an amplifier or a decoder
compatible with these multi-channel sources to this terminal, and set “DIGITAL AUDIO OUTPUT”
correctly. (See page 29 of the INSTRUCTIONS.)
*1Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
*2“DTS” and “DTS 2.0 + Digital Out” are trademarks of Digital Theater Systems, Inc.
Њᘖв݉ࡓؼၸʫ᎕څᑶࡗ
• вᆧᐉၸʫಚᑶወ᎕LINE OUT / 2nd AUDIO OUT!
᎔ᕻᑵལۑ༙é
ະᆑ؞ϠᑵལሆᇫڄၪçϠᑵལۑ༙ூʓмପϐளéࡖᏁþʓмପϐ ኌ՟·ი
اڄ୶29ࡗé
• вDIGITAL OUT᎕δዖၸʫ!
Џၷʪ᎔ᆚᇫۑ༙ለ PCMçDolby Digital*1çDTS*2çࡖᏁMPEGé༴શቁኌ՟
·იاڄ୶35ࡗé
ึ࠱ᐺદϠᑵལࡖᛏسçϨDolby Digital ֜DTSçઅႩϠᑵལࡖᛏسߟࡾࣅڄ
؞ʨ༱ᇫв༳ၷʪçՓᇧ׆īᆚᇫࡖᏁ᎔Ĭéኌ՟·იاڄ୶29
ࡗé
*1ΊDolby Laboratories ᛱ௪éӬèDolbyႩᕻD ৩༙ݵDolby Laboratories ڄᆤé
*2īDTSĬ֜īDTS 2.0 + Digital OutĬݵᆚᇫᅬԦ˙ڄᆤé
ݮᄑ
•ۙᎴുጜᔄê
*ᐓފ߹иለᏃ֜෨иለᏃݵѴ᙮ᇧ%
•ྑກˀ়ોê
*ᐓފ෦иለᏃݵѴʕ%
•ಚᑶወԆЊᑶࡗê
*ᐓފಙᑵ᎔ለᏃݵѴഠཔ%
•ᑶࡗê
*ᐓފಙᑵ᎔ၷʪݵѴϙ%
*ᐓފಙᑵڄ(L)è(R) ၷʪڄ࠷(–) ݵѴθψϙ%
•ࡗʹᓿࡗᛐê
*݈ϙၷʪႩԾԽݵѴ՟·ཛഠ֜ཛ۹ڄྐለ%
•͵ጆഛᇋê
*ᐓފಙᑵ᎔ၷʪݵѴϙ%
*ᐓފಙᑵڄ(L)è(R) ၷʪڄ࠷(–) ݵѴθψϙ%
•͵ጆҭθˀ়ይіê
*ݵѴʵࡌڄጅஇ%
TROUBLESHOOTING
•The fuse blows.
*Are the red and black leads connected correctly?
•Power cannot be turned on.
*Is the yellow lead connected?
•No sound from the speakers.
*Is the speaker output lead short-circuited?
•Sound is distorted.
*Is the speaker output lead grounded?
*Are the “–” terminals of L and R speakers grounded in common?
•Noise interfere with sounds.
*Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
•Unit becomes hot.
*Is the speaker output lead grounded?
*Are the “–” terminals of L and R speakers grounded in common?
•This unit does not work at all.
*Have you reset your unit?
Instal1-3_DV7206_006A_pre.indd 2Instal1-3_DV7206_006A_pre.indd 2 1/18/06 9:04:17 AM1/18/06 9:04:17 AM

3
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Removing the unit
Before removing the unit, release the rear section.
*3When you stand the unit, be careful not to damage the fuse on the rear.
*3৹ʹጅçʮ˻ʿ࠱๑ᖢנ௰ڄۘᎳീé
ϰ༬༬éׇ֤ϛᄮڸؼ˗
ʓࡒڄ࿌༱ڷΕʄյܓڄϯ༫ദҺéϨسЉᖅçᄔ࠱Љᘕࢭ˔άڄཊçቁώJVC
ԆԾࡖᛏ˜ኀࢭ˔άաᏻ˙༿é
ëϨسʿᇧ׆Ϩщᇧϙϯ༫ʹጅçᏻቁϐڄӑிʆ࢜գϯ༫é
Do the required electrical connections.
නмᄔڄྐཔé
Bend the appropriate tabs to hold the
sleeve firmly in place.
Ҿᛮጅೋڄߴдçӕࢭጅೋԕ֣Ϛᄭ
ڷػ˖é
When using the optional stay / ࠝΈᆊނ
Screw (option)
ᒘീ·ڄ
Stay (option)
ᆉށ·ڄ
Fire wall
Վػ
Dashboard
ᄭڷػ
Install the unit at an angle of less than 30˚.
અʹጅϯ༫Ϛ˲ؠ30˚ڄԴܾé
When installing the unit without using the sleeve / ࠝˀՠΈࢮጆೌϰ༬͵ጆ
In a Toyota car for example, first remove the car radio and install the unit in its place.
ᕙΉ(TOYOTA) ԆԾբ ࡛ζ֊ԆԾЂࡖጅç݈અʹጅ༫ʈմڏڄтé
*4
Not supplied for this unit.
*4
ʿᎲʹጅಏաé
Flat type screws (M5 ×8 mm)*4
Ꮓᒘീ (M5 ×8 mm)*4
Pocket
ڏೋ
Flat type screws (M5 ×8 mm)*4
Ꮓᒘീ (M5 ×8 mm)*4
Bracket*4
Ёࣙ*4
Bracket*4
Ёࣙ*4
Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws are
used, they could damage the unit.
ٍิ !ӕʹጅϯ༫ϚЁࣙʕç՟·8 mmۂڄᒘീéϨ՟·ཫۂڄᒘീç๑ᖢʹጅé
։͵ጆ
Ϛ؛ֈʹጅۮçᏻઅʹጅ݈௰ڄ֣׆֜௰˜ᖑළé
Insert the two handles, then pull them as
illustrated so that the unit can be removed.
ݝ࿌Εçઅղػܓӕ˾ʈᆥç݈ძᗌ
ϙનղώղӕ˾çʹጅᎲ˃é
Instal1-3_DV7206_006A_pre.indd 3Instal1-3_DV7206_006A_pre.indd 3 1/18/06 9:04:23 AM1/18/06 9:04:23 AM

ENGLISH
4
To external components (see diagram )
вஇάኌ࿌ڷ )
VIDEO OUT
(see diagram / ኌ࿌ڷ )
DIGITAL OUT
(see diagram / ኌ࿌ڷ )
A
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious
damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
1Connect the colored leads of the power cord in the order specified in the illustration below.
2Connect the antenna cord.
3Finally connect the wiring harness to the unit.
Line out (see diagram )
᎔ၷʪኌ࿌ڷ
Typical connections / նܔڅોሉ٘
LINE IN
(see diagram / ኌ࿌ڷ )
2nd AUDIO OUT
(see diagram / ኌ࿌ڷ )
To subwoofer (see
diagram )
вඟࡌјࡖಙᑵ
ኌ࿌ڷ )
ˁ
ોሉۯ!அᐓފԆԾ˖ڄለཔéʿᇧڄለࠓʹጅᘷࡌ๑ᖢé
ྐʍለڄ˺ለ֜ԾԽڄ˺ለϚᖄиʕЉʿψé
1՜ຖʓ࿌Ε˃ЎҺྐለڄᖄиለé
2 અ˭ለڄྐለ৹գé
3 ఛ݈çӕለӧڄᏃϚʹጅʕé
Rear ground terminal
ʹጅ݈ࠌϙၷʪ
15 A fuse
15 AۘᎳീ
Black
෨и
Blue with white stripe
ᕇиઘЉΎиঙ
Red
߹и
Yellow *2
෦и*2
To metallic body or chassis of the car
вہᚙᝂԆԾנᇟ
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
вۘᎳീవ˔˖ڄۈᚙၷʪçۘᎳീవ˔ؠԾ༫ྐЖߟ
·ؠཔᓭළᘕݔ׆12 V
To an accessory terminal in the fuse block
вۘᎳീవ˔˖ڄۈᚙၷʪ
Ignition switch
ᓭළᘕ
*1Not supplied for this unit.
*1ʿᎲʹጅಏաé
Fuse block
ۘᎳീవ˔
Brown
ሶи
Orange with white stripe
ዻиઘЉΎиঙ To car light control switch
вԆԾԾጜվළᘕ
To cellular phone system
в˾ጅԦ
Light green
ଠႋи To parking brake, metallic body or chassis of the car
в˾۫ԾለèہᚙᝂԆԾנᇟ
*2
Before checking the operation of this unit prior to
installation, this lead must be connected, otherwise
power cannot be turned on.
*2
ʹጅ͵ϯ༫çනмʳѕٶٜᐓފ˃ۮç
ෝӕለʕçѴ۱ʿළ૧ྐé
Left speaker (front)
ಙᑵۮ
Right speaker (front)
ಙᑵۮ
Left speaker (rear)
ಙᑵ݈
Right speaker (rear)
ಙᑵ݈
Purple
ാи
Purple with black stripe
ാиઘЉ෨иঙ
Green
ႋи
Green with black stripe
ႋиઘЉ෨иঙ
Gray
Ни
Gray with black stripe
НиઘЉ෨иঙ
White
Ύи
White with black stripe
ΎиઘЉ෨иঙ
ELECTRICAL CONNECTIONS ྑཕો
To the automatic antenna if any (250 mA max.)
вб˭ለࠜЉ༫ఛʨ250 mA
Blue
ᕇи
To the remote lead of other equipment (200 mA max.)
вմ༫ʕڄჲለఛʨ200 mA
Antenna
connector
˭ለ
Instal4-6_DV7206_006A_pre.indd 4Instal4-6_DV7206_006A_pre.indd 4 1/18/06 9:07:43 AM1/18/06 9:07:43 AM

5
B
When installing the monitor in a location where it can be seen by the driver
Connect the parking brake wire to the parking brake system built in the car.
When installing the monitor in a location where it cannot be seen by the driver
Connect the parking brake wire to metallic body or chassis or the car.
C
D
Required connections for DVD playback / ᆒ؟DVDᄕڅો
Audio/video control amplifier or the decoder compatible
with the multichannel digital sources
ࡖᏁƄඁᏁվ؞ʨႩϠᑵལᆚᇫࡖᛏس
ߟࡾࣅڄ༱ᇫ
KV-MR9010
9-INCH WIDESCREEN MONITOR (not supplied)
ʭᅛၑܳΕʿᎲʹጅಏա
Digital optical cable (not supplied)
ᆚᇫγងʿᎲʹጅಏա DIGITAL OUT
See “About sounds
reproduced through the rear
terminals.”
ኌīЉᘕб݈ࡒػၷʪ᎔
ڄᑵࡖĬ௰˜é
KS-HP2
Cordless headphones (not supplied) *4
ለЫጅʿᎲʹጅಏա*4
Video cord (not supplied)
ඁᏁྐងʿᎲʹጅಏա
*4
To listen to disc playback sound while in Dual Zone operations (see page 23 of INSTRUCTIONS).
*4
ϚᕻዬѕЂγၪᆑ؞ᑵࡖኌ՟·იاڄ୶23ࡗé
or /
Rear side
݈
Connecting the parking brake wire / ોг˿۬Կዘሉ
Parking brake wire (light green)
˾۫Ծለଠႋи
To metallic body or chassis of the car
вہᚙᝂԆԾנᇟ
Parking brake switch (inside the car)
˾۫ԾළᘕтʝԾ˖
Parking brake
˾۫Ծ
આΖወϰ༬ϛጆߢսڅу
અ˾۫ԾለвԾ˖ڄ˾۫ԾԦé
Parking brake wire (light green)
˾۫Ծለଠႋи
*3Not supplied for this unit.
*3ʿᎲʹጅಏաé
આΖወϰ༬ϛጆߢˀսڅу
અ˾۫ԾለвہᚙᝂԆԾנᇟé
Connecting the crimp connector / ોгҜʫોᏄ
Wire connecting the battery and the parking brake switch.
ྐЖ֜˾۫Ծළᘕڄྐለé
Attach the parking brake wire to this point.
˾۫ԾለвЏளé
Contact the metallic part of the crimp to the wires inside.
՟қʪᏃہᚙ௰˜֜˖௰ྐለ᙮é
Pinch the crimp firmly.
қႌқʪᏃé
Signal Cord (not supplied)
ۑ༙ྐងʿᎲʹጅಏա
Instal4-6_DV7206_006A_pre.indd 5Instal4-6_DV7206_006A_pre.indd 5 1/18/06 5:28:03 PM1/18/06 5:28:03 PM

6
Other external component / յોஈέ
CAUTION /
ʯ˼î
Before connecting the external components , make sure that the unit is turned off.
இά˃ۮçζᇧ׆ʹጅʵᘕé
*8Connecting cord supplied for your CD changer
*8 ڄCD ಗၪకڄྐង
Connecting the external components / ોյોஈέ
JVC CD changer
JVC CDಘၫወ
External component
ોஈέ
3.5 mm stereo mini plug
3.5 mm Θᝂᑵіࣙ
*10 AUX Input Adapter KS-U58 (not supplied for this unit)
*10 AUX᎔ʈቱKS-U58 (ʿᎲʹጅಏա)
*9Line Input Adapter KS-U57 (not supplied for this unit)
*9ྐཔ᎔ʈቱKS-U57 ʿᎲʹጅಏա
•Set “EXT IN” for the external input setting (See page 26 of the INSTRUCTIONS.) / આ௱᎕ʉׇг“EXT IN” (௱᎕ʉ) (ኍՠΈკبڅ୷26 ࡘê)
•Set “CHANGER” for the external input setting (See page 26 of the INSTRUCTIONS.) / આ௱᎕ʉׇг“CHANGER” (ಘၫወ) (ኍՠΈკبڅ୷ 26 ࡘê)
*7iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
*7iPod ݵApple Computer, Inc. ăᙧسྐ༃˙ĄϚࠀ˪մࣁٌڄᆤé
CD changer, Apple iPod®, or JVC D. player / CDಘၫወéApple iPod® JVC D. player
F
E
CD changer jack
CDಗၪࣙ External component
ોஈέ
Connecting the external amplifiers and/or subwoofer / ોો؟ʩወ֝ƅචࡍљࡗಚᑶወ
You can connect amplifiers to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it
can be controlled through this unit.
• Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker
leads of this unit unused.
؞ʨ˥ঠڄԆԾΘᝂᑵԦé
ëઅჲለᕇиઘЉΎиঙ֜մ༫ʕڄჲለ৹գç۔ཫʹጅන
мჲé
• આಚᑶወ֝͵ጆᔄෆèκોʖୋ؟ʩወêઆ͵ጆڅಚᑶወોሉ؟ˀΈê
Rear speakers
݈ಙᑵ
JVC Amplifier
JVC ୋ؟ʩወ
Remote lead
ჲለ
Y-connector (not supplied for this unit)
Y-ܓለʿᎲʹጅಏա
Remote lead (Blue with white stripe)
ჲለᕇиઘЉΎиঙ
To the remote lead of other equipment or automatic antenna if any
вմ༫ʕڄჲለб˭ለࠜЉ༫
Front speakers
ۮಙᑵ
*6Firmly attach the ground wire to the metallic body or to the chassis of
the car—to the place uncoated with paint (if coated with paint, remove
the paint before attaching the wire). Failure to do so may cause damage
to the unit.
*6અϙለႩہᚙԾᝂږԆԾנᇟႌંçளᏻ༳ԅЉூٛ
ွᕒႵϨسʵดʕٛွçϚྐለۮçઅٛွսéϨسʿ
ᆟç๑ᖢʹጅé
Apple iPod
(separately purchased)
Apple iPod ᒯ
JVC D. player
(separately purchased)
JVC D. player ᒯ
CD changer jack
CDಗၪࣙ
You can connect these components as illustrated below. The iPod*7or D. player can be connected using
an interface adapter (not supplied)—KS-PD100 (for iPod) or KS-PD500 (for D. player).
અஇάϨ࿌Εනмé՟·ߍࡒቱʿక—KS-PD100 (iPod·
KS-PD500* player·iPod*7 * playeré
JVC Amplifier
JVC ୋ؟ʩወ
JVC Amplifier
JVC ୋ؟ʩወ
Front speakers
ۮಙᑵ
Subwoofer
ඟࡌјࡖಙᑵ
External component
ોஈέ
*5
Signal cord (not supplied for this unit)
*5ۑ༙ྐងʿᎲʹጅಏա
or
Instal4-6_DV7206_006A_pre.indd 6Instal4-6_DV7206_006A_pre.indd 6 1/18/06 2:34:06 PM1/18/06 2:34:06 PM
Other manuals for KD-DV7206
1
This manual suits for next models
1
Table of contents
Other JVC Car Receiver manuals