JVC KD-HDR52 User manual

KD-AHD57 / KD-HDR52
GET0837-001A [J]
ENGLISH
ESPAÑOL
FRANÇAIS
CD RECEIVER
INSTRUCTION MANUAL
RECEPTOR CON CD
MANUAL DE INSTRUCCIONES
RÉCEPTEUR CD
MANUEL D’INSTRUCTIONS
For customer Use:
Enter below the Model No. and Serial No. which are located on
the top or bottom of the cabinet. Retain this information for future
reference.
Model No.
Serial No.
Please read all instructions carefully before operation to obtain the
best possible performance from the unit.
Por favor lea detenidamente este manual para comprender a fondo
todas las instrucciones y obtener un máximo disfrute de esta unidad.
Veuillez lires les instructions attentivement avant d’utiliser l’appareil
afin d’obtenir les meilleures performances possibles de l’appareil.
EN_KD-AHD57[J]3.indd 1 9/13/12 4:07:17 PM

2
CONTENTS BEFORE USE
BEFORE USE 2
BASICS 3
GETTING STARTED 4
CD / USB / iPod 5
AUX 8
How to read this manual
• Operations explained mainly using
buttons on the faceplate.
• [XX] indicates the selected items.
•
( « XX) indicates references are available
on the stated page number.
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accident.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of
the output level.
General:
• Avoid using the USB device or iPod/iPhone if it might hinder driving safety.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.
Remote control (RM-RK52):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or
equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Keep battery out of reach of children and in original package until ready to use. Dispose of used batteries
promptly. If swallowed, contact a physician immediately.
For USA-California Only:
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material—special handling
may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
2
Maintenance
Cleaning the unit: Wipe off dirt on the faceplate with a dry silicon or soft cloth.
Cleaning the connector: Detach the faceplate and clean the connector with a
cotton swab gently, being careful not to damage the connector.
Handling discs:
• Do not touch the recording surface of the disc.
• Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
• Do not use any accessories for the disc.
• Clean from the center of the disc and move outward.
• Clean the disc with a dry silicon or soft cloth. Do not use any solvents.
• When removing discs from this unit, pull them out horizontally.
• Remove burrs from the center hole and disc edge before inserting a disc.
Pandora® 9
AUDIO SETTINGS 10
Connector (on the reverse
side of the faceplate)
MORE INFORMATION 11
TROUBLESHOOTING 12
SPECIFICATIONS 13
INSTALLATION / CONNECTION 14
RADIO 6
EN_KD-AHD57[J]f.indd 2 10/12/12 3:58:05 PM

3
BASICS
To Do this (on the faceplate) Do this (on the remote control)
Turn on the power Press LSOURCE.
• Press and hold to turn off the power. ( not available )
Adjust the volume Turn the volume knob. Press VOL + or VOL –.
Press the volume knob to mute the sound or pause playback.
• Press again to cancel.
Press to mute the sound or pause playback.
• Press again to cancel.
Select a source • Press LSOURCE repeatedly.
• Press LSOURCE, then turn the volume knob within 2 seconds.
Press SOURCE repeatedly.
Change the display
information
Press DISP repeatedly.
( « 11)
• Press and hold to scroll the current display information. ( not available )
Faceplate
Attach
How to reset
Detach
Remote control (RM-RK52)
Volume knob
(turn/press) Loading slot
Detach button
Remote sensor
(Do not expose to bright sunlight.)
How to replace the battery
Your preset adjustments will
also be erased.
Pull out the insulation sheet
when using for the first time.
Display window
ENGLISH
EN_KD-AHD57[J]3.indd 3 9/13/12 4:07:18 PM

4
GETTING STARTED
Cancel the demonstration
1 Press and hold MENU .
2 Press the volume knob to select [DEMO] .
3 Turn the volume knob to select [DEMO OFF] , then press the knob.
4 Press MENU to exit.
Set the clock
1 Press and hold MENU .
2 Turn the volume knob to select [CLOCK] , then press the knob.
3 Turn the volume knob to select [CLOCK SET] , then press the knob.
4 Turn the volume knob to select the day, then press the knob.
5 Turn the volume knob to adjust the hour, then press the knob.
6 Turn the volume knob to adjust the minute, then press the knob.
7 Press MENU to exit.
Set the basic settings
1 Press and hold MENU .
2 Turn the volume knob to make a selection, then press the knob.
• See the following table for selection.
3 Press MENU to exit.
To return to the previous hierarchy, press G HD .
1
2
3
Default: XX
CLOCK
CLOCK ADJ AUTO: The clock time is automatically set using the Clock Time (CT) data in FM Radio
Broadcast Data System signal. ; OFF: Cancels.
CLOCK DISP ON: The clock time is shown on the display even when the unit is turned off. ;
OFF: Cancels.
DIMMER
DIMMER SET Selects the display and button illumination adjusted in the [BRIGHTNESS] setting.
AUTO: Changes between the day and night adjustments when you turn off or on the car
headlights.*
1
; ON: Selects the night adjustments. ; OFF: Selects the day adjustments.
BRIGHTNESS Sets the display and button brightness for day and night separately.
1 DAY/NIGHT: Select day or night.
2 BUTTON ZONE/DISP ZONE: Select the zone for setting.
3 Set the brightness level (00 to 31). (Default: DAY: 31 ; NIGHT: 15)
DISPLAY
SCROLL
* 2 ONCE: Scrolls the display information once. ; AUTO: Repeats scrolling at 5-second
intervals. ; OFF: Cancels.
(Not applicable for HD Radio stations. The display information always scroll regardless of
the setting made.)
TAG DISPLAY ON: Shows the TAG information while playing MP3/WMA files. ; OFF: Cancels.
IPOD SWITCH*
3
HEAD MODE: Controls music playback only from this unit. ; IPOD MODE: Controls music
playback from both the unit and iPod/iPhone. ; EXT MODE: Controls music playback only
from the iPod/iPhone.
SRC SELECT
AM
* 4 ON: Enables AM in source selection. ; OFF: Disables.
PANDORA
* 4 ON: Enables PANDORA in source selection. ; OFF: Disables.
AUX
* 4 ON: Enables AUX in source selection. ; OFF: Disables. ; BT ADAPTER: Select when the
KS-BTA100 Bluetooth adapter is connected to the AUX jack (
« 8). The source name will
change to BT AUDIO.
*1The illumination control wire connection is required.
( « 15)
*2Some characters or symbols will not be shown correctly (or will be blanked).
*3Displayed only when the source is USB-IPOD.
*4Not displayed when the corresponding source is selected.
EN_KD-AHD57[J]3.indd 4 9/13/12 4:07:19 PM

5
CD / USB / iPod
To Do this CD USB iPod
Select a track/file Press E/ F(or 2/3on RM-RK52). *2
Select a folder
(MP3/WMA)
Press 1∞/25(or 5/∞on RM-RK52). —
Reverse/Fast-forward Press and hold E/ F(or 2/3on RM-RK52). *2
Select a track/file
from a list
1Press MENU
2Turn the volume knob to make a selection, then press the knob.
• MP3/WMA file: Select the desired folder, then a file.
• iPod or JVC Playlist Creator (JPC) / JVC Music Control (JMC) file*3: Select
the desired file from the list (PLAYLISTS, ARTISTS, ALBUMS, SONGS,
PODCASTS*4, GENRES, COMPOSERS*4).
• To return to the previous hierarchy, press GHD.
• To cancel, press MENU.
Note: Turn the volume knob quickly to fast-search.
*5
Repeat play Press 6Brepeatedly to make a selection.
• Audio CD or JPC / JMC file: TRACK RPT, RPT OFF
• MP3/WMA file: TRACK RPT, FOLDER RPT, RPT OFF
• iPod: ONE RPT, ALL RPT
*5
Random play Press 5Arepeatedly to make a selection.
• Audio CD: ALL RND, RND OFF
• MP3/WMA file or JPC / JMC file: FOLDER RND, ALL RND, RND OFF
• iPod: SONG RND, ALBUM RND*6, RND OFF
*5
Start playback
CD
The source changes to CD and playback starts.
• To eject a disc, press 0.
USB
The source changes to USB and playback
starts.
iPod/iPhone
The source changes to USB-IPOD and
playback starts.
Press 4 iPod MODE repeatedly to select
the control mode (
[HEAD MODE] / [IPOD
MODE]
/ [EXT MODE] ).
• See also
[IPOD SWITCH] . ( « 4)
*1Do not leave the cable inside the car
when not using.
Label side
USB input terminal
USB input terminal USB 2.0 cable
*1
(commercially available)
USB 2.0 cable
*1
(accessory of the iPod/iPhone)
: Applicable
— : Not applicable
*4Only for iPod.
*5Applicable under
[HEAD MODE] only. ( « 4)
*6Not applicable for some iPod/iPhone.
*2Applicable under
[HEAD MODE] and [IPOD MODE] only. ( « 4)
*3Only for files registered in the database created with JPC / JMC.
( « 11)
ENGLISH
EN_KD-AHD57[J]3.indd 5 9/13/12 4:07:19 PM

6
You can tune in to both conventional and HD Radio broadcasts.
• To find HD Radio stations in your area, visit <http://www.hdradio.com>.
Search for a station or channel
1 Press LSOURCE to select FM or AM.
2 Press and hold GHD to select the tuning mode.
• SEEK MODE = HD SEEK : Search for HD Radio broadcast only.
• SEEK MODE = MANUAL SEEK : Search for both conventional and HD Radio
broadcasts.
3 Press E/F(or 2/3on RM-RK52) to search for a station or channel
automatically.
(or)
Press and hold E/F(or 2/3on RM-RK52) until “M” flashes, then press
repeatedly to search for a station or channel manually.
• When receiving a HD Radio station, “HD” lights up on the digital audio reception,
or flashes on the analog audio reception.
• When receiving a conventional FM stereo broadcast, “ST” lights up.
To select an HD Radio multicast channel
Many HD Radio stations offer more than one channel programming. This service is
called multicasting. While receiving HD Radio multicast channels....
Press E/Fto select your desired channel (HD1 to HD8).
“LINKING” appears while linking to a multicast channel.
RADIO
Select the HD Radio reception mode
While receiving an HD Radio broadcast, you can select the reception mode of digital
audio, analog audio, or both.
Press GHD to make a selection.
•
AUTO (default): Switches between digital and analog audio automatically. “HOLD”
flashes if the radio station forces only analog reception.
•
ANALOG : Tunes to analog audio only. “HOLD” lights up.
•
DIGITAL : Tunes to digital audio only. “HOLD” lights up.
• This setting does not take effect for the conventional FM/AM stations.
• The setting automatically returns to
[AUTO] when you tune in to another
broadcast.
Store a station or channel
You can store up to 18 stations for FM and 6 stations for AM.
• HD Radio multicast channels can also be stored.
While listening to a station or channel....
Press and hold one of the number buttons (1to 6) to store.
(or)
1 Press and hold the volume knob until “PRESET MODE” flashes.
2 Turn the volume knob to select a preset number, then press the knob.
The preset number flashes and “MEMORY” appears.
Select a stored station or channel
Press one of the number buttons (1to 6).
(or)
1 Press MENU.
2 Turn the volume knob to select a preset number, then press the knob.
EN_KD-AHD57[J]4.indd 6 9/19/12 9:50:19 AM

7
RADIO
Other settings
1 Press and hold MENU.
2 Turn the volume knob to select [TUNER] , then press the knob.
3 Turn the volume knob to make a selection (see the following table), then
press the knob.
4 Press MENU to exit.
Default:
XX
SSM For FM: SSM 01 – 06 / SSM 07 – 12 / SSM 13 – 18:
For AM: SSM 01 – 06:
Automatically presets up to 18 stations for FM and 6 stations for AM. “SSM” stops
flashing when the first 6 stations are stored. Select SSM 07 – 12 / SSM 13 – 18 to
store the following 12 stations for FM.
AREA AREA US: For North/Central/South America, AM/FM intervals: 10 kHz/200 kHz. ;
AREA EU: For any other areas, AM/FM intervals: 9 kHz/50 kHz. ; AREA SA: For
some South American countries, AM/FM intervals: 10 kHz/50 kHz.
MONO Displayed only when the source is FM.
MONO ON: Improves the FM reception, but the stereo effect will be lost. ;
MONO OFF: Cancels.
IF BAND AUTO: Increases the tuner selectivity to reduce interference noises from adjacent
stations. (Stereo effect may be lost.) ; WIDE: Subjects to interference noises from
adjacent stations, but sound quality will not be degraded and the stereo effect will
remain.
RADIO TIMER Turns on the radio at a specific time regardless of the current source.
1 ONCE/ DAILY/ WEEKLY/ OFF: Select how often the timer will be turned on.
2 FM/ AM: Select the FM or AM band.
3 01 to 18 (for FM)/ 01 to 06 (for AM): Select the preset station.
4 Set the activation day and time.
• “
M ” lights up when complete.
Radio Timer will not activate for the following cases.
• The unit is turned off.
• [OFF] is selected for [AM] in [SRC SELECT] after Radio Timer for AM is selected.
(
« 4)
Tag and purchase your favorite songs from iTunes Store
Some HD Radio broadcasts provide Program Service Data (PSD) for songs. You can
tag the song and store its PSD up to 50 songs while listening to the song.
• By using the tagging function, you can easily purchase the songs from iTunes
Store.
• For the best compatibility of iTunes Tagging, use the latest software versions with
the iPod/iPhone that can be connected to this unit.
( « 11)
Tag the song
While receiving a song with PSD (“TAG” lights up)...
Press TAG.
“TAG SAVED” appears when the song is stored on the unit.
• When
pressing TAG within 10 seconds before or after the PSD changes (while
“TAG” flashes), the tags for two songs are stored.
To check the number of tagged songs stored on the unit
Press and hold TAG.
To delete the tagged songs from the unit
1 Press and hold MENU.
2 Turn the volume knob to select [TAG ALL CLR] , then press and hold the knob.
“COMPLETED” appears when all the tagged songs are deleted.
1
ENGLISH
EN_KD-AHD57[J]4.indd 7 9/19/12 9:37:41 AM

8
AUX
Use a portable audio player
1 Connect a portable audio player (commercially available).
2 Select [ON] for [AUX] in [SRC SELECT] . ( « 4)
3 Press LSOURCE to select AUX.
4 Turn on the portable audio player and start playback.
Use a 3-core plug head stereo mini plug for optimum audio output.
Use a Bluetooth® device
1 Connect the Bluetooth adapter, KS-BTA100 (separately purchased).
2 Register (pair) the Bluetooth device with KS-BTA100.
3 Select [BT ADAPTER] for [AUX] in [SRC SELECT] . ( « 4) .
4 Press LSOURCE to select BT AUDIO
5 Start using the Bluetooth device.
For details, refer to the instruction manual of KS-BTA100.
3.5 mm (1/8") stereo mini plug with “L”
shaped connector (commercially available)
Portable audio player
Auxiliary input jack
Auxiliary input jack
Blue/white Blue/white: Remote
Black Black: Ground
Brown Brown: Tel muting
Wiring harness of the unit
(
« 15)
RADIO
Transfer the tagged PSD to your iPod/iPhone
Connect the iPod/iPhone to the unit.
The source changes to “USB-IPOD,” and starts transferring the tagged PSDs to the
iPod/iPhone automatically.
• While transferring, “TAG” flashes and the number of PSD transferring and stored
appears. When all the tagged PSDs are transferred, “COMPLETED” appears.
Notes:
• Your iPod/iPhone must have 50 MB free space which is required for transferring a
tagged PSD.
• During the transferring process:
– Do not change the source.
– Do not disconnect the iPod/iPhone.
• When the connected iPod/iPhone is not compatible with iTunes Tagging you
cannot transfer the tagged PSDs.
Purchase songs from iTunes Store
1 Connect the iPod/iPhone to the PC.
2 Synchronize the iPod/iPhone on the iTunes.
The tagged PSDs are transferred to the PC and iTunes displays the list of
the tagged songs. After the data transfer is completed, the stored PSDs are
automatically deleted from the iPod/iPhone.
Notes:
• iTunes 7.4 or later version is required.
• For details about iPod/iPhone and iTunes, refer also to the instructions supplied
with the iPod/iPhone or visit <http://www.apple.com>.
2
3
EN_KD-AHD57[J]4.indd 8 9/19/12 9:37:41 AM

9
Pandora®
Preparation:
Install the latest version of the Pandora application into
your device (iPhone/iPod touch), then log in and create
an account with Pandora.
• Select
[ON] for [PANDORA] in [SRC SELECT] . ( « 4)
Start listening
1 Open the Pandora application on your device.
2 Connect your device to the USB input terminal.
The source changes to PANDORA and broadcast
starts.
* Do not leave the cable inside the car when not
using.
About Pandora
• Pandora is only available in the US.
• Because Pandora is a third-party service, the
specifications are subject to change without prior
notice. Accordingly, compatibility may be impaired or
some or all of the services may become unavailable.
• Some functions of Pandora cannot be operated from
this unit.
• For issues using the application, please contact Pandora
at [email protected].
• If the version of the OS of the connected iPhone is
earlier than 4.0, start the Pandora application before
selecting the PANDORA source.
To Do this
Pause or resume
playback
Press the volume knob (or on RM-RK52).
Thumbs up or thumbs
down
Press 1/ 2.
• If thumbs down is selected, the current track is skipped.
Skip a track Press F(or 3on RM-RK52).
Create a new station 1 Press MENU.
2 Turn the volume knob to select [NEW STATION] , then press the knob.
3 Turn the volume knob to select [FROM TRACK] or [FROM ARTIST] , then press
the knob.
A new station is created based on the current song or artist.
Search for a registered
station
1 Press MENU.
2 Turn the volume knob to make a selection, then press the knob.
[BY DATE] : According to the registered date.
[A–Z] : Alphabetical order.
3 Turn the volume knob to select the desired station, then press the knob.
Bookmark a song or
artist information
1 Press and hold the volume knob.
2 Turn the volume knob to select [THIS TRACK] or [THIS ARTIST] , then press the
knob.
“BOOKMARKED” appears and the information is stored to your device.
The bookmark is available on your Pandora account but not on this unit.
USB input terminal
USB 2.0 cable*
(accessory of the iPhone/iPod touch)
ENGLISH
EN_KD-AHD57[J]f.indd 9 10/12/12 4:00:30 PM

10
AUDIO SETTINGS
1 Press and hold MENU.
2 Turn the volume knob to select [EQ SETTING] or [AUDIO] , then press the knob.
3 Turn the volume knob to make a selection (see the following table), then
press the knob.
Repeat step 3until the desired item is selected.
4 Press MENU to exit.
• To return to the previous hierarchy, press GHD.
Default:
XX
EQ SETTING
EQ PRESET FLAT /
NATURAL / DYNAMIC / VOCAL BOOST / BASS BOOST /
USER: Selects a preset equalizer.
EASY EQ Adjust your own sound settings.
SUB.W
*1 –08 to +08 (00)
BASS LVL –06 to +06 (00)
MID LVL –06 to +06 (00)
TRE LVL –06 to +06 (00)
• The setting is stored to [USER] in [EQ PRESET].
PRO EQ
1 BASS / MIDDLE / TREBLE: Select a sound tone.
2 Adjust the sound elements of the selected sound tone.
BASS Frequency: 60/ 80/ 100/ 200 Hz Default: (80 Hz)
Level: –06 to +06 (00)
Q: Q1.0/ Q1.25/ Q1.5/ Q2.0 (Q1.0)
MIDDLE Frequency: 0.5/ 1.0/1.5/ 2.5 kHz Default: (1.0 kHz)
Level: –06 to +06 (00)
Q: Q0.75/ Q1.0/ Q1.25 (Q1.25)
TREBLE Frequency: 10.0/ 12.5/ 15.0/ 17.5 kHz Default: (10.0 kHz)
Level: –06 to +06 (00)
Q: Q FIX (Q FIX)
• The setting is stored to [USER] in [EQ PRESET].
AUDIO
FADER
*2
*3
R06 — F06 (00): Adjusts the front and rear speaker output balance.
BALANCE
*3
L06 — R06 (00): Adjusts the left and right speaker output balance.
BASS BOOST +01 / +02: Selects your preferred bass boost level. ; OFF: Cancels.
LOUD LOW / HIGH: Boosts low or high frequencies to produce a well-balanced
sound at low volume. ; OFF: Cancels.
VOL ADJUST –05 — +05 (00): Presets the volume adjustment level of each source
(compared to the FM volume level). Before adjustment, select the source you
want to adjust. (“VOL ADJ FIX” appears if FM is selected.)
L/O MODE SUB.W / REAR: Selects whether rear speakers or a subwoofer are connected
to the REAR/SW line out terminals on the rear panel (through an external
amplifier).
SUB.W
*4
ON / OFF: Turns on or off the subwoofer output.
SUB.W LPF
*5
THROUGH: All signals are sent to the subwoofer. ; LOW 55Hz / MID 85Hz /
HIGH 120Hz: Audio signals with frequencies lower than 55 Hz/ 85 Hz/ 120 Hz
are sent to the subwoofer.
SUB.W LEVEL
*5
–08 — +08 (00): Adjusts the subwoofer output level.
BEEP ON / OFF: Activates or deactivates the keypress tone.
TEL MUTING
*6
ON: Mutes the sounds while using the cellular phone (not connected through
KS-BTA100). ; OFF: Cancels.
AMP GAIN LOW POWER: Limits the maximum volume level to 30. (Select if the
maximum power of each speaker is less than 50 W to prevent damaging the
speakers.) ; HIGH POWER: The maximum volume level is 50.
*1Displayed only when
[L/O MODE] is set to [SUB.W] and [SUB.W] is set to [ON] .
*2If you are using a two-speaker system, set the fader level to
[00] .
*3This adjustment will not affect the subwoofer output.
*4Displayed only when
[L/O MODE] is set to [SUB.W] .
*5Displayed only when
[SUB.W] is set to [ON] .
*6Does not work if
[BT ADAPTER] is selected for [AUX] in [SRC SELECT] .
EN_KD-AHD57[J]3.indd 10 9/13/12 4:07:20 PM

11
MORE INFORMATION
About discs and audio files
• This unit can only play the following CDs:
• This unit can play back multi-session discs;
however, unclosed sessions will be skipped
during playback.
• Unplayable discs:
- Discs that are not round.
- Discs with coloring on the recording surface or
discs that are dirty.
- Recordable/ReWritable discs that have not
been finalized.
- 8 cm CD. Attempting to insert using an
adapter may cause malfunction.
• DualDisc playback: The Non-DVD side of a
“DualDisc” does not comply with the “Compact
Disc Digital Audio” standard. Therefore, the use
of Non-DVD side of a DualDisc on this product
cannot be recommended.
• Playable files:
- File extensions: MP3 (.mp3), WMA (.wma)
- Bit rate: MP3: 8 kbps — 320 kbps
WMA: 32 kbps — 192 kbps
- Sampling frequency:
MP3: 48 kHz, 44.1 kHz, 32 kHz, 24 kHz,
22.05 kHz, 16 kHz, 12 kHz, 11.025 kHz, 8 kHz
WMA: 48 kHz, 44.1 kHz, 32 kHz
- Variable bit rate (VBR) files.
• Maximum number of characters for file/
folder name:
It depends on the disc format used (includes 4
extension characters—<.mp3> or<.wma>).
- ISO 9660 Level 1 and 2: 64 characters
- Romeo: 64 characters
- Joliet: 32 characters
- Windows long file name: 64 characters
About USB devices
• This unit can play MP3/WMA files stored on a
USB mass storage class device.
• You cannot connect a USB device via a USB hub
and Multi Card Reader.
• Connecting a cable whose total length is longer
than 5 m may result in abnormal playback.
• The maximum number of characters for:
- Folder names: 63 characters
- File names: 63 characters
- MP3 Tag: 60 characters
- WMA Tag: 60 characters
• This unit can recognize a total of 65 025 files,
255 folders (255 files per folder including
folder without unsupported files), and of 8
hierarchies.
• This unit cannot recognize a USB device whose
rating is other than 5 V and exceeds 1 A.
About iPod/iPhone
• Made for
- iPod touch (1st, 2nd, 3rd, and 4th
generation)
- iPod classic
- iPod with video (5th generation)*
- iPod nano (1st*, 2nd, 3rd, 4th, 5th and 6th
generation)
- iPhone, iPhone 3G, 3GS, 4, 4S
* [IPOD MODE]/ [EXT MODE] are not
applicable.
• It is not possible to browse video files on the
“Videos” menu in [HEAD MODE].
• The song order displayed on the selection menu
of this unit may differ from that of the iPod/
iPhone.
• If some operations are not performed
correctly or as intended, visit: <http://www3.
jvckenwood.com/english/car/index.html>
(English website only).
About JVC Playlist Creator and JVC Music Control
• This unit supports the PC application JVC Playlist Creator and AndroidTM application JVC Music Control.
• When you play audio files with song data added using the JVC Playlist Creator or JVC Music Control,
you can search for audio files by Genres, Artists, Albums, Playlists and Songs.
• JVC Playlist Creator and JVC Music Control are available from the following web site:
<http://www3.jvckenwood.com/english/car/index.html> (English website only).
About HD Radio™ Technology
• Program Service Data provides song name, artist, station ID, and other relevant
data streams.
• Adjacent to traditional main stations are HD2/HD3 Channels, providing new
original formats on the FM dial.
• HD Radio broadcasts deliver crystal clear, CD-like digital audio quality to
consumers.
• iTunes® Tagging provides users the means to “tag” broadcast radio content for later
review and purchase from the iTunes® Store.
Display information
“NO TEXT,” “NO DATA” or “NO NAME” appears if unavailable.
FM or AM Station name (PS)*
1
= Frequency = Program type (PTY)*
1
or ANALOG = Title*
1
*
2
= Day/Clock = (back to the beginning)
HD RADIO Call Sign*
3
= Frequency = Program type (PTY)*
4
= PSD = Day/Clock = (back to
the beginning)
CD or USB Album title/Artist
= Track title = Track no./Playing time = Day/Clock = (back to
the beginning)
USB-IPOD [HEAD MODE] or [IPOD MODE]: Album title/Artist
= Track title = Track no./Playing
time
= Day/Clock = (back to the beginning)
[EXT MODE]: EXT MODE Day/Clock
PANDORA Station name
= Album title/Artist = Track title = Playing time = Day/Clock =
(back to the beginning)
AUX AUX Day/Clock
BT AUDIO BT AUDIO Day/Clock
*
1
For FM Radio Broadcast Data System stations only.
*
2
Title information shown is dependent on the broadcast station.
*
3
Displayed only when a call sign is received.
*
4
When no program type (PTY) is received, “HD RADIO” appears.
ENGLISH
EN_KD-AHD57[J]f.indd 11 10/30/12 5:17:21 PM

12
TROUBLESHOOTING
Symptom Remedy
Sound cannot be heard. • Adjust the volume to the optimum level.
• Check the cords and connections.
• Be sure the rear ground terminal connected to the car’s chassis
are using shorter and thicker cords.
“MISWIRING CHK WIRING
THEN RESET UNIT” /
“WARNING CHK WIRING THEN
RESET UNIT” appears and no
operations can be done.
Check to be sure the terminals of the speaker wires are insulated
properly, then reset the unit. If this does not solve the problem,
consult your nearest service center.
Source cannot be selected. Check the [SRC SELECT] setting. (
« 4)
Radio reception is poor. /
Static noise while listening to
the radio.
• Connect the antenna firmly.
• Pull the antenna out all the way.
Sound quality changes when
receiving HD Radio stations/
channels.
Fix the reception mode to either [ANALOG] or [DIGITAL].
(
« 6)
No sound can be heard. • [ANALOG] is selected when receiving all digital broadcast of HD
Radio station. Select [AUTO] or [DIGITAL]. (
« 6)
• [DIGITAL] is selected when receiving a weak digital signals
or receiving conventional radio broadcast. Select [AUTO] or
[ANALOG]. (
« 6)
iTunes Tagging
“MEMORY FULL” You are trying to store the 51st PSD. Transfer the tagged PSDs to
the iPod/iPhone, or clear all tagged PSDs.
“TAG ALREADY SAVED” You are trying to tag the same song for the 2nd time .
“NO TAG DATA” The broadcast currently received does not support the iTunes
Tagging or the broadcast does not provide PSD.
“CAN’T TRANS IPOD FULL” The memory of the iPod/iPhone is full.
“UNSUPPORTED DEVICE
FOR TAGGING”
The connected iPod/iPhone is not compatible with iTunes
Tagging.
“TRANS ERROR” The iPod/iPhone is disconnected during data transfer.
“TRANS OFF” Data transfer is canceled.
Correct characters are not
displayed.
This unit can only display uppercase letters, numbers, and a
limited number of symbols.
“PLEASE” and “EJECT” appear
alternately.
Press
0 , then insert the disc correctly.
Symptom Remedy
“IN DISC” appears. Make sure nothing is blocking the loading slot when you eject the
disc.
Disc cannot be ejected. Press and hold
0 to forcibly eject the disc. Be careful not to drop the
disc when it is ejected.
Playback order is not as
intended.
The playback order is determined by the file name (USB) or the order
in which files were recorded (disc).
Elapsed playing time is
not correct.
This depends on the recording process earlier.
“NOT SUPPORT” appears
and track skips.
Check whether the track is a playable format. (
« 11)
“CANNOT PLAY” flashes
and/or connected device
cannot be detected.
• Check whether the connected device is compatible with this unit and
ensure the files are in supported formats. (
« 11)
• Reattach the device.
“READING” keeps
flashing.
• Do not use too many hierarchical levels and folders.
• Reload the disc or reattach the USB device.
The iPod/iPhone does
not turn on or does not
work.
• Check the connection between this unit and iPod/iPhone.
• Detach and reset the iPod/iPhone using hard reset.
• Check whether the [IPOD SWITCH] setting is appropriate. (
« 4)
Pandora
“ADD ERROR” /
“SEARCH ERR”
New station creation is unsuccessful.
“CHK DEVICE” Check the Pandora application on your device.
“NO SKIPS” The skip limit has been reached.
“NO STATIONS” No registered station is found.
“STATION LIM” The number of registered stations has reached it’s limit. Retry after
deleting an unnecessary station in your device.
“UPGRADE APP” Make sure you have installed the latest version of the Pandora
application on your device.
If you have any troubles, try the following:
1 Check TROUBLESHOOTING
2 Reset the unit («3)
3 Contact (USA only)
Call: 1-800-252-5722 ( or ) visit: http://www.jvc.com
EN_KD-AHD57[J]5.indd 12 9/28/12 11:25:21 AM

13
SPECIFICATIONS
Audio amplifier
Power Output 20 W RMS ×4 Channels at 4 Ω
and ≤ 1% THD+N
Load Impedance 4 Ω (4 Ω to 8 Ω allowance)
Frequency Response 40 Hz to 20 000 Hz
Signal-to-Noise Ratio 80 dBA (reference: 1 W into 4 Ω)
Line-Out, Subwoofer-Out Level/
Impedance
2.5 V/20 kΩ load (full scale)
Output Impedance ≤ 600 Ω
Tuner
FM Frequency Range 87.9 MHz to 107.9 MHz (200 kHz step)
87.5 MHz to 108.0 MHz (50 kHz step)
Usable Sensitivity 11.3 dBf (1.0 μV/75 Ω)
50 dB Quieting Sensitivity 19.3 dBf (2.5 μV/75 Ω)
Alternate Channel Selectivity 65 dB (at 400 kHz)
Frequency Response 20 Hz to 20 000 Hz (HD Radio broadcast)
40 Hz to 15 000 Hz (Conventional broadcast)
Stereo Separation 70 dB (HD Radio broadcast)
48 dB (Conventional broadcast)
AM Frequency Range 530 kHz to 1 700 kHz (10 kHz step)
531 kHz to 1 611 kHz (9 kHz step)
Sensitivity/Selectivity 20 μV/70 dB
Frequency Response 40 Hz to 15 000 Hz (HD Radio broadcast)
Stereo Separation 70 dB (HD Radio broadcast)
CD player
Signal Detection System Non-contact optical pickup (semiconductor laser)
Number of Channels 2 channels (stereo)
Frequency Response 5 Hz to 20 000 Hz
Signal-to-Noise Ratio 98 dB
Wow and Flutter Below measurable limit
USB
USB Standard USB 1.1, USB 2.0
Data Transfer Rate (Full Speed) Max. 12 Mbps
Compatible Devices Mass storage class
Compatible File Systems FAT 32/16/12
Playable Audio Formats MP3/WMA
Maximum Supply Current DC 5 V
d 1 A
General
Power Requirements (Operating Voltage) DC 14.4 V (11 V to 16 V allowance)
Grounding System Negative ground
Allowable Operating Temperature 0°C to +40°C (32°F to 104°F)
Dimensions
(W × H × D)
Installation Size
(approx.)
182 mm × 53 mm × 159 mm
(7-3/16" × 2-1/8" × 6-5/16")
Panel Size (approx.) 188 mm × 59 mm × 13 mm
(7-7/16" × 2-3/8" × 9/16")
Weight (excluding accessories) 1.2 k
g (2.lbs)
Subject to change without notice.
ENGLISH
EN_KD-AHD57[J]3.indd 13 9/13/12 4:07:21 PM

14
INSTALLATION / CONNECTION
Warning
• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car
chassis or Ground wire (black) to prevent a short circuit.
• Insulate unconnected wires with vinyl tape to prevent a short circuit.
• Be sure to ground this unit to the car’s chassis again after installation.
Caution
• For safety’s sake, leave wiring and mounting to professionals. Consult
the car audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal
parts of this unit during and shortly after use of the unit. Metal parts
such as the heat sink and enclosure become hot.
• Do not connect the
· wires of speaker to the car chassis, Ground wire
(black), or in parallel.
• Connect speakers with a maximum power of more than 50 W. If the
maximum power of the speakers is lower than 50 W, change the
[AMP GAIN] setting to avoid damaging the speakers. (
« 10)
• Mount the unit with the angle of 30° or less.
• If your vehicle wiring harness does not have the ignition terminal,
connect Ignition wire (red) to the terminal on the vehicle’s fuse box
which provides 12 V DC power supply and is turned on and off by the
ignition key.
• After the unit is installed, check whether the brake lamps, blinkers,
wipers, etc. on the car are working properly.
• If the fuse blows, first make sure the wires are not touching car’s
chassis, then replace the old fuse with one that has the same rating.
Basic procedure
1 Remove the key from the ignition switch, then
disconnect the ·terminal of the car battery.
2 Connect the wires properly.
See Wiring connection. ( « 15)
3 Install the unit to your car.
See Installing the unit (in-dash mounting).
4 Connect the ·terminal of the car battery.
5 Reset the unit. ( « 3)
Do the required wiring.
(
« 15)
How to remove the unit
Installing the unit (in-dash mounting)
When installing without the mounting sleeve
Bracket (not supplied)
Bend the appropriate tabs to hold
the sleeve firmly in place.
Make sure the direction of
the trim plate.
Pocket
Flat or round head screws (not supplied)
M5 × 8 mm (M5 × 3/8")
EN_KD-AHD57[J]5.indd 14 9/28/12 11:25:38 AM

15
STEERING
WHEEL
REMOTE
Car fuse block
Ignition switch
Recommended
connection
Light blue/yellow
KD-AHD57 only
Vehicle-specific Wiring Harness
(separately purchased)
For more information:
Metra Electronics:
www.metraonline.com
Scosche Industries: www.scosche.com
Blue/white: To amplifier
Blue: To power antenna
Make this connection if
your vehicle factory wiring
harness does not have “12 V
ignition switch” wire.
Separate red wire
Wiring connection
Signal cord (not supplied)
Remote wire
(not supplied)
Rear ground terminal
To the steering wheel
remote control adapter
Fuse (10 A)
Antenna terminal
Front output
Rear/subwoofer output
JVC Amplifier
Factory wiring harness
(vehicle)
Vehicle dashboard
Part list for installation
( ×2 )
( ×1 )
( ×1 )
( ×1 )
( ×1 )
A Faceplate
B Mounting sleeve
C Trim plate
D Wiring harness
E Extraction key
Black: Ground
Yellow: Battery 12 V
White: Front speaker (left)
White/black
Gray: Front speaker (right)
Gray/black
Green: Rear speaker (left)
Green/black
Purple: Rear speaker (right)
Purple/black
Join the same color wires together.
Red: Ignition 12 V
Orange/white: Illumination
Brown: Tel muting
Blue/white: Remote (200 mA max.)
ENGLISH
EN_KD-AHD57[J]3.indd 15 9/13/12 4:07:21 PM

1112 DTSMDTJEIN
• Microsoft and Windows Media are either registered trademarks or trademarks
of Microsoft Corporation in the United States and/or other countries.
• HD Radio Technology manufactured under license from iBiquity Digital
Corporation. U.S. and Foreign Patents. HD Radio™ and the HD, HD Radio, and
“Arc” logos are proprietary trademarks of iBiquity Digital Corp.
• “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has
been designed to connect specifically to iPod, or iPhone, respectively, and has
been certified by the developer to meet Apple performance standards. Apple
is not responsible for the operation of this device or its compliance with safety
and regulatory standards. Please note that the use of this accessory with iPod,
or iPhone may affect wireless performance.
• iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple
Inc., registered in the U.S. and other countries.
• Pandora, the Pandora logo, and the Pandora trade dress are trademarks or
registered trademarks of Pandora Media, Inc., used with permission.
• Android is trademark of Google Inc.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. The user could
lose the authority to operate this equipment if an unauthorized change or
modification is made.
FCC NOTE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
In compliance with Federal Regulations, following are reproductions of labels
on, or inside the product relating to laser product safety.
JVC KENWOOD Corporation
2967-3, ISHIKAWA-MACHI,
HACHIOJI-SHI, TOKYO, JAPAN
THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR
SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
Location : Bottom Plate
Información acerca de la eliminación de equipos eléctricos y electrónicos
al final de la vida útil (aplicable a los países que hayan adoptado sistemas
independientes de recogida de residuos)
Los productos con el símbolo de un contenedor con ruedas tachado no podrán
ser desechados como residuos domésticos. Los equipos eléctricos y electrónicos
al final de la vida útil, deberán ser reciclados en instalaciones que puedan dar
el tratamiento adecuado a estos productos y a sus subproductos residuales
correspondientes. Póngase en contacto con su administración local para
obtener información sobre el punto de recogida más cercano. Un tratamiento
correcto del reciclaje y la eliminación de residuos ayuda a conservar los recursos
y evita al mismo tiempo efectos perjudiciales en la salud y el medio ambiente.
Information on Disposal of Old Electrical and Electronic
Equipment (applicable for countries that have adopted
separate waste collection systems)
Products with the symbol (crossed-out wheeled bin) cannot
be disposed as household waste. Old electrical and electronic
equipment should be recycled at a facility capable of handling
these items and their waste byproducts. Contact your local
authority for details in locating a recycle facility nearest to you.
Proper recycling and waste disposal will help conserve resources
whilst preventing detrimental effects on our health and the
environment.
© 2012 JVC KENWOOD Corporation
EN_KD-AHD57[J]3.indd 16 9/13/12 4:07:22 PM

WHEN
IT
IS
NOT
REQUIRED
TO
DETACH
THE
FR
~
ONT
CONTROL
PANEL
FROM
THE
MAIN
UNIT,
US
IE
THE
PROVIDED
SCREW
TO
ATTACH
THE
C
~
ONTROL
PANEL
TO
T'
HIE
,
MA
!
IN
UNIT.
GE40401-001A

w
0::
:z
tn~O
~
:::»
~
w w
tn
~
c
:::::;
0
tn
i=
LL
1:!::!
:::::»
w
:z
1-
.m
ce
:z
w
0
~
...J
S::!
cc
m
o:::
w
c(
t;
...J
O'W
ID
...J<CcC
:::E
w (.)
0 w
:::::;)
~
~
c
LL
cC
W
...J
(.)
I=
w
...J
w
m
w
==»
c a
:3
~
i=
W
'W
tn
:::»
w
:ESlf=
.....
t:i
w
w·
:s
o
>
w
t:l
0
0:::
0:::
:::E
- -
w
t:i
t:i
~
0:::
0:::
1.\
CA
uTI
0 N CONNECT
BLACK
WIRE
((f)
GND) TO GROUND FIRST.
~
OTHERWISE, DAMAGE TO YOUR
UNIT
MAY OCCUR.
INCORRECT
CO~NECTION
CAUSES SERIOUS DAMAGE TO THIS UNIT
PLEASE READ INSTALLATION/CONNECTION
MANUAL
CAREFULLY.
CD
CONNECT GROUND FIRST
METALLIC BODY OR CHASSIS
OF THE CAR
(3)
CONNECTANTENNA TERMINAL
(2)
@
CONNECT OTHER WIRES
_,
~
CONNECT POWER CORD TO
.THE UNIT
-
IQ
·~

CANADA
ONLY
JVC
OWNER'S COPY OF WARRANTY CARD
COPIE D'ENREGISTREMENT DE LA GARANTIE
DU PROPRIETAIRE
CANADA
SEULEMENT
(Save sales docket together with this warranty card, as a proof of date of purchase.
La facture et cette garantie sont vos preuves de
Ia date d'achat; rangez-les.)
MODEL . SERIAL
NO . .
MODELE . .........
.. ...... ............ .. . . . . . .. .......... NO DE SERlE .
Purchase from.
Achete chez
Dealer's Address
Adresse du Vendeur'
Owner's Name
No.
No
Nom du Proprietaire
.'.
Owner's Address .
Adresse du Proprietaire·
..
BT-52009-1
(0912)
No.
No
Rue
Date purchased .
Date achete ·
Street Apt.
Rue App.
Printed in Indonesia
Product Registration/Enregistrement du produit
We suggest that you register your product since it will enable us
to contact you directly if it is ever necessary to correct a safety related
condition
in your product.
You can register at http://www.jvc.ca/www/Support/Warranty.aspx
Nous vous conseillons d'enregistrer votre produit, car il nous permettra de vous
contacter directement
si jamais elle est necessaire pour corriger un probleme lie a Ia securite de votre
produit.
Vous pouvez vous inscrire a http://www.jvc.ca/www/Support/Warranty.aspx
WAIIIANTY
GAlANT IE
JVC CANADA INC.
6070 kestrel Road , Missisauga , Ontario, L5T 1 S8 Canada
TEL : [phone] FAX : [phone]
http://www. jvc .ca
JVC CANADA
INC . (hereafter called "JVC") gives
the following express warranty for each new JVC
product distributed
in Canada by J VC and sold
by an authorized JVC dealer.
JVC warrants that this JVC product is free, under
normal use
and maintenance, from any defects in
material and wo rkmanship subject to the following
terms
and conditions:
1.
To Obtain Warranty Service:
(a) JVC Product requiring service must be
Presented together with Proof of purchase.
(b) The JVC product must be brought in for
service to an authorized JVC Service Centre .
2. Limitation:
This Warranty shall not apply to:
(a) Repair or replacement of any cabinets,
batteries, plates, connection cords, anten-
nas, dust covers, knobs, speaker grills,
speaker cones , projection screens , projection
screen savers, and all accessories.
(b) Any defects caused or repairs required as a
result of misuse, abusive operation, negli-
gence, improper use and/or insuffic i ent care .
(c) Any defect caused or repairs required as
a result of not following the instructions
in
the operation manua l.
(d) Any JVC product tampered with, adjusted
or repaired by any party other than JVC or
authorized JVC Service Centre personnel.
JVC CANADA INC. ( ci-apres appele "JVC")
enonce
Ia garantie expresse suivante pour tout
nouveau produit JVC distribue
au Canada par JVC
et vendu par un detaillant JVC autorise.
JVC vous garantit que
ce produit est degage, sous
utilisation
et entretien normal, de tout defaut
materiel et de fabrication sous reserve des
modalites
et conditions suivantes :
1. Pour obtenir un service
de garantie :
(a) Les produits jvc necessitant un service doit
etre presentee avec
Ia prenve d'achat
(b) Le produit JVC doit etre apporte pour
service chez
un centre de service JVC
autor
ise .
2. Restrictions:
Cette garantie
ne s'applique pas aux :
(a) Reparation ou r emplacement de tout
cabinet, batteries, panneau avant, cordons
de raccord, antennes, housses de
protection, boutons, couverts de haut-
parleur, cones
de haut-parleur, ecrans de
projection, protecteurs d'ecran de projection
et to us les accessoires.
(b) Tous defauts occasionnes ou reparations
requises suite a une utilisation abusive,
mauvaise, negligente et/ou
une utilisation
incorrecte.
(c) Tous defauts occasionnes ou reparations
requises suite a !'omission
de suivre les
recommandations
du manuel d'instruction.
(d) Tout produ it JVC altere, ajuste ou repare par
tout autre entreprise que JVC ou un centre
de service d'entretien
ou de service
autorise JVC.

(e) Any JVC products on which the serial
num-ber has been defaced, modified
or
removed.
(f) Maintenance, cleaning or periodic check-up
(g) Conversion to foreign or domestic voltage or
frequency.
(h) Any
JVC product without the Canadian
Electrical Safety Regulations ID.
(i) Any JVC products used for commercial or
institutional, rental, or display purposes.
Parts
...... 1 year (except video head -90
days)
Labour... 90 days
(j ) Any JVC product which has been resold and
no longer owned by the original purchaser.
(k) Product purchased from "outside Canada
",
"bankruptcy" or "liquidator".
(e) Tout produit JVC
doni le numero de serie a
ete altere, modifie ou enleve.
(f) L'entretien, les verifications periodiques et
nettoyage.
(g) La
conversion a une frequence ou une
tension etrangere ou domestique.
(h)
Tout produit JVC n' ayant pas le sigle
d'identification conforme aux normes
electriques Canadiennes (GSA).
(i) Pour tout produit utilise a des fins
commerciales, institutionnelles, de location
ou utilise a
des fins d'etalage.
Pieces
............ 1 An (Excepte les tetes
video- 90 jours)
Main d'ceuvre
.. . 90 Jours
(j) Tout produit JVC ayant ete revendu et qui
n'est plus
Ia propriete de l'acheteur original.
(k) Produit achete a "l'exterieur du Canada
",
provenant d'une "faillite" ou d'un "liquidateur ".
WARRANTY TERM (VALID FROM THE DATE OF PURCHASE)
CONDITIONS DE GARANTIE (VALABLE aPARTIR DE LA DATE D'ACHAT)
r ,
PRODUCT PARTS (Years) Labour (Years) 1
PRODUIT PIECES (annees) MAIN-D'OEUVER (a nnee s)
Projection TV In-Home Service
Colour
TV In-Home (25" and above)
D-ILA
Rear Pro jection In-Home Service
LCD TV In-Home Service (25" and above)
Ecrans
de projection Service aDomicile
Ecrans
de TV Couleur Service aDomicile (25 " et plus)
TV projection arriEne D-ILA Service aDomicile
Ecrans
de LCD Service aDomicile (25" et plus)
• In-home service to be provided where available
I
Where it is not available, the Purchaser must assume the responsibility and expense for the proper
packing, shipment
and all costs associated with the delivery of the equipment to and from the closest
JVC Authorized Service Centre.
• Service adomicile fourni par
un detaillant disponible.
S'
il n'y a pas de service JVC disponible a proximite, l'acheteur doit assumer Ia responsabilite et les
coOts pour un emballage adequat, !'expedition, ainsi que tous les coOts associes a Ia livraison de
l'equipement chez et depuis le detaillant JVC autorise le plus pres pour un service d'entretien
Receivers
and Home Speakers purchased separately, Front
I
Projection and Car Audio "ARSENAL" Series 2 2
Recepteurs et Hauts-Parleurs achetes separement, Projecteur
Avant et Audio d' Auto de Serie " ARSENAL "
AC Adapters, Remote Controls, Headphones, Microphones and 90 DAYS
90 DAYS
Projector Lamps
Adaptateurs AC , Telecommande,Casque D'ecoute, Microphones
90 JOURS 90 JOURS
et Lampe de Projecteur
Wood Cone Speakers 5 5
Enceinte a Cone en Bois
All Other Categories 1 1
Toutes les autres categories
I
J
( I) Any defects caused by fire, flood, lightning,
power surge,
or other events beyond the
control of JVC.
(m) FOR AUTO PRODUCTS
Warranty does not cover elimination of car
static or electrical interferences, cleaning
of head, adjustments, or labour cost for the
removal or reinstallation
of the unit for
repair.
3. Standards:
If any defects should be found in a JVC product
within the applicable terms, necessary repairs
shall be made at no cost to the purchaser for
parts or labour when JVC acknowledges that
such defects are due to faulty material or work-
manship.
4. Exclusion of All Other Express Warranties:
This warranty constitutes the entire express
warranty given by JVC for JVC products and
no dealer or service centre personnel
or his,
its or their agent or employee is, or are autho-
rized to extend or enlarge this warranty on be-
half
of JVC.
5. Disclaimer of Consequential Damage:
To the extent the law permits JVC disclaims
any responsibility for loss of time or use of its
product , transportation costs , or any other
indirect, incidental or consequential damage or
inconvenience.
(I) Tout
dommage cause par le feu, une
inondation, un eclair, une surtension ou tout
autre evenement hors du contr61e de JVC.
(m)
POUR LES PRODUITS D'AUTOMOBILE
La garantie ne couvre pas !'elimination
d'interferences statiques ou electriques de
Ia
voiture , le nettoyage de tete, les
ajustements et les coOts de main d'ceuvre
associes a l' enlevement ou a Ia
reinstallation de !'unite pour reparation.
3. Criteres:
Si un produit JVC s'averait defectueux, selon les
conditions
applicables , les reparations
necessaires seront effectues sans coOts
additionnels a l'acheteur pour les pieces et
Ia
main d'ceuvre lorsque JVC reconnait que de telles
defectuosites sont causees par une defectuosite
de materiel ou de fabrication.
4. Exclusion de toutes autres garanties expresses :
Cette garantie constitue l'entiere garantie express
donnee par JVC pour les produits JVC. Nul
representant ou employe d'
un detaillant ou d' un
service d'entretien n'est autorise aprolonger cette
garantie au nom de JVC.
5. Denegation des dommages indirects :
Dans Ia mesure permise par Ia loi , JVC nie toute
responsabilite pour perle de temps
ou d'usage de
ses produits, des
coOts de transport ou tout autre
dommage ou inconvenient indirect, accidentel et
consequent.
JVC CANADA INC.
Service toll free # : 1-800-964-2650
E-mail:[email protected]