JVC KW-XR614 Guide

1
KW-XR614
Installation/Connection Manual
0110DTSMDTJEIN
EN
© 2010 Victor Company of Japan, Limited
GET0666-009A
[UI]
• To prevent short circuits:
–Disconnect the battery’s negative terminal and make all electrical connections before installing the unit.
–Cover the terminals of the UNUSED leads with insulating tape.
• Be sure to ground this unit to the car’s chassis again after installation.
• Replace the fuse with one of the specified rating.
• Connect speakers with a maximum power of more than 50 W (impedance of 4 Ω to 8 Ω). Otherwise, change the <AMP GAIN> setting. (See page 25 of the INSTRUCTIONS.)
• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.
12 V DC, NEGATIVE ground
To the car system
You need the installation kits which corresponds to your car. Check the battery system in your car
WARNINGS
Heat sink
INSTALLATION
The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
In-dash mounting
Audio system originally installed in the car
Car dashboard
If there is an interfering tab on the
mounting bracket, bend it flat.
Screw removed from the car
Mounting bracket removed from the car
Firmly attach the ground wire to the metallic body of the car using the screw originally fixed
to the metallic body of the car.
Installing with the mounting brackets from the car
Install the unit at an angle of less than 30˚.
Part list
AFlat countersunk screws—M5 × 8 mm (×8)
BRound head screws—M5 × 8 mm (×8)
CPlate for use with a Nissan car (×1)
DPower cord (×1)
When installing the unit in a
Nissan car
Fix the supplied plate as illustrated.
PRECAUTIONS on power supply and speaker connections
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.
• The fuse blows. ] Are the red and black leads connected correctly?
• Power cannot be turned on.
] Is the yellow lead connected?
• No sound from the speakers.
] Is the speaker output lead short-circuited?
• “PROTECT” appears on the display and no operation can be done.
] Is the speaker output lead short-circuited or touches the chassis of the car/head unit? ; Have you reset your unit?
• Sound is distorted.
] Is the speaker output lead grounded? ; Are the “–” terminals of L and R speakers grounded in common?
• Noise interfere with sounds.
] Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
• This unit becomes hot.
] Is the speaker output lead grounded? ; Are the “–” terminals of L and R speakers grounded in common?
• This unit does not work at all.
] Have you reset your unit?
TROUBLESHOOTING
Install_KW-XR614_009A_f.indd 1Install_KW-XR614_009A_f.indd 1 2/1/10 10:21:59 AM2/1/10 10:21:59 AM

2
Connecting the external components in series
When connecting the external components, refer also to the manuals supplied for the components and adapter.
You can connect the following components through the various JVC adapters to the expansion port.
• Connection cords may need to be purchased separately.
Component Adapter Model name
Bluetooth device Bluetooth adapter KS-BTA200
Portable audio player with line output jacks Line input adapter KS-U57
Portable audio player with 3.5 mm stereo mini jack AUX input adapter KS-U58
Black
Fuse block
Ignition switch
Blue (white stripe)
Red
Yellow*3
To the metallic body or chassis of the car
To an accessory terminal
To a live terminal (constant 12 V)
To the automatic antenna if any (250 mA max.)
White
White (black stripe)
Gray
Gray (black stripe)
Green
Green (black stripe)
Purple
Purple (black stripe)
Y-connector*1
Y-connector*1
Remote lead
Remote lead
To the blue (white stripe) lead of
the unit
Rear speakers or subwoofer (Make the <L/O MODE> setting accordingly,
see page 24 of the INSTRUCTIONS.)
Rear ground terminal
15 A fuse
Antenna input
Front speaker (left)
Front speaker (right)
Rear speaker (left)
Rear speaker (right)
ELECTRICAL CONNECTIONS
Reset the unit.
JVC Amplifier
JVC Amplifier
Connecting the external amplifier or subwoofer
To the remote lead of other equipment (200 mA max.)
Blue
IMPORTANT: A custom wiring harness (separately purchased) which is suitable for your car is recommended for connection between the unit and your car.
• Consult your JVC car audio dealer or a company supplying kits for details.
DPower cord
*1Not supplied for this unit.
*2Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint.
*3Before checking the operation of this unit prior to installation, this lead must be connected; otherwise, the power cannot be turned on.
*4To use these components, set the external input setting correctly (see page 25 of the INSTRUCTIONS).
A KS-BTA200
B *4KS-U57 / KS-U58
To disconnect...
Expansion port of the unit
Caution:
Before connecting the external components, make sure that the unit is turned off.
Expansion port
Steering wheel remote input
To the blue (white stripe) lead of
the unit
Signal cord*1
Signal cord*1
Front speakers
Orange with white stripe To car light control switch
Install_KW-XR614_009A_f.indd 2Install_KW-XR614_009A_f.indd 2 2/1/10 10:22:00 AM2/1/10 10:22:00 AM