JVC KW-DB60 Guide

1
KW-DB60
Installation/Connection Manual
1112MYHSANJEIN
EN
© 2012 JVC KENWOOD Corporation
LVT2445-002A
[B]
INSTALLATION
WARNINGS
• Mounting and wiring this product requires skills and experience. For safety’s sake, leave this work to professionals. If you experience problems during installation, consult your JVC car audio dealer.
• The unit can only be installed in a car with a 12 V DC power supply, negative ground.
• Disconnect the battery’s negative terminal and make all electrical connections before installing the unit.
• Connect speakers with a maximum power of more than 50 W (impedance of 4 Ω to 8 Ω). Otherwise, change the <AMP GAIN> setting. (See page 18 of the INSTRUCTIONS.)
• Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals.
• If the fuse blows, first make sure the wires are not touching to cause a short circuit, then replace the old fuse with one that has the same rating.
• Install this unit in the console of your vehicle.
• Mount the unit so that the mounting angle is 30° or less.
• Be sure to ground this unit to the car’s chassis again after installation.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.
• Do not touch the metal part of this unit during and shortly after the use of the unit. Metal part such as the heat sink and enclosure become hot.
In-dash mounting
(A) Installing with the supplied sleeve
Audio system originally installed
in the car
Audio system originally installed in the car
Car dashboard
Car dashboard
If there is an interfering tab on the
mounting bracket, bend it flat.
Screw removed from the car
Mounting bracket removed from the car
Firmly attach the ground wire to the metallic body of the car using the screw originally fixed
to the metallic body of the car.
(B) Installing with the mounting brackets from the car
Install the unit at an angle of less than 30˚.
Part list
ASleeve (fitted to the main unit when shipped)
.......................................................................................................(×1)
BBrackets (fitted to the main unit when shipped)
.......................................................................................................(×2)
C* Flat countersunk screws—M5 × 8 mm
.......................................................................................................(×8)
D* Round head screws—M2.6 × 3 mm
.......................................................................................................(×4)
ERound head screws—M5 × 8 mm
.......................................................................................................(×8)
FPower cord
.......................................................................................................(×1)
GTrim plate
.......................................................................................................(×1)
HLINE OUT cord
.......................................................................................................(×1)
* Four of these screws are fitted to the main unit when
shipped. Keep these screws for installation use if
necessary.
• The fuse blows. h Are the red and black leads connected correctly?
• Power cannot be turned on. h Is the yellow lead connected?
• No sound from the speakers. h Is the speaker output lead short-circuited?
• “MISWIRING CHK WIRING THEN RESET UNIT”/“WARNING CHK WIRING THEN RESET UNIT” appears on the display and no operation can be done. h Is the speaker output lead short-circuited or touches the
chassis of the car/head unit? ; Have you reset your unit?
• Sound is distorted.
h Is the speaker output lead grounded? ; Are the “–” terminals of L and R speakers grounded in common?
• Noise interfere with sounds.
h Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
• This unit becomes hot. h Is the speaker output lead grounded? ; Are the “–” terminals of L and R speakers grounded in common?
• This unit does not work at all.
h Have you reset your unit?
TROUBLESHOOTING
    

2
*1Not supplied for this unit.
*2Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint.
*3Make the <L/O MODE> setting accordingly, see page 18 of the INSTRUCTIONS.
ELECTRICAL CONNECTIONS
STEERING
WHEEL
REMOTE
FRONT
REAR
SUBWOOFER
Reset the unit
Signal cord*1Extension lead*1
Remote lead To the blue (white stripe) lead
of the unit
JVC Amplifier
Connecting the external amplifiers and/or subwoofer
– – – – – – – – – – – – – – – – – – – – – – – or – – – – – – – – – – – – – – – – – – – – – –
Connecting the Bluetooth adapter or portable audio player
KS-BTA100
(separately purchased )
Portable audio player, etc.*1
3.5 mm stereo mini plug *1
Make the <SRC SELECT> setting accordingly, see pages 14 and 19 of the INSTRUCTIONS.
Rear ground terminal
HLINE OUT cord (supplied)
10 A fuse
Aerial input
From DAB aerial
From Radio aerial
Remote adapte*1
For some VW/Audi or Opel (Vauxhall) automobiles
You may need to modify the wiring of the supplied power cord as illustrated.
• Contact your authorized car dealer before installing this unit.
Original wiring
Modified wiring 1
Use modified wiring 2if the unit does not turn on.
ISO connector
Y: Yellow
R: Red
Modified wiring 2
IMPORTANT: A custom wiring harness (separately purchased) which is suitable for your car is recommended for connection between the unit and your car.
Consult your JVC car audio dealer or kits supplying company for details
about connection.
(A) If your car has an ISOterminal (B) If your car does NOT have an ISOterminal
Custom wiring harness
(separately purchased)
Custom wiring harness
(separately purchased)
B1/B2 Rear speaker, right (Purple/Purple, black stripe) (+/–)
B3/B4 Front speaker, right (Gray/Gray, black stripe) (+/–)
B5/B6 Front speaker, left (White/White, black stripe) (+/–)
B7/B8 Rear speaker, left (Green/Green, black stripe) (+/–)
A2 To mobile phone system (Brown)
A4 Car battery 12 V (Yellow)
A5 Remote lead/power aerial, 200 mA max. (Blue, white stripe)
A6 To car light control switch (Orange, white stripe)
A7 Accessory terminal (Red)
A8 Metallic body/chassis of the car (Black)
FPower cord (supplied)
FPower cord (supplied)
FPower cord (supplied)
ISO connector
FRONT : Front speakers
REAR : Rear speakers or subwoofer *3
Light Blue (yellow stripe)
To the brown lead of the
supplied power cord
F
To the blue (white stripe) lead
of the supplied power cord
F
Blue, white stripe
Brown
Black Ground
PRECAUTIONS on power supply and speaker connections
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.
• Connect the speaker wires correctly to the terminals to which they correspond. The unit may damaged or fail to work if you share the G wires or ground them to any metal part in the car.
• Your setting data is erased every time the ignition switch is off.
    