JVC DT-V9L5 User manual

LCT2704-001A
For Customer Use:
Enter below the Serial No. which is located
on the rear of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
: DT-V9L5
:
MULTI FORMAT LCD MONITOR
INSTRUCTIONS
DT-V9L5
®
DT-V9L5_EN_1.indb 1DT-V9L5_EN_1.indb 1 10/10/2012 5:18:31 PM10/10/2012 5:18:31 PM

2
Safety Precautions
WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE. NO OBJECTS FILLED WITH LIQUIDS,
SUCH AS VASES, SHALL BE PLACED ON THE
APPARATUS.
IMPORTANT SAFEGUARDS
Electrical energy can perform many useful functions. This unit has
been engineered and manufactured to assure your personal safety.
But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRIC
SHOCK OR FIRE. In order not to defeat the safeguards incorporated
into this product, observe the following basic rules for its installation,
use, and service. Please read these “IMPORTANT SAFEGUARDS”
carefully before use.
All the safety and operating instructions should be read before the•
product is operated.
The safety and operating instructions should be retained for future•
reference.
All warnings on the product and in the operating instructions•
should be adhered to.
All operating instructions should be followed.•
POWER CONNECTION
The power supply voltage rating of this product is AC 120 V.
The power cord attached conforms to the following power supply
voltage and countries. Use only the power cord designated to
ensure safety and EMC regulations of each country.
Not all types of power cords are supplied to this product.
For U.S.A. and Canada: AC
120 V
This plug will fit only into a grounded power outlet. If you are
unable to insert the plug into the outlet, contact your electrician to
install the proper outlet. Do not defeat the safety purpose of the
grounded plug.
This product should be operated only with the type of power
source indicated on the label. If you are not sure of the type of
power supply of your home, consult your product dealer or local
electric power company.
Warning: This is a class A product. In a domestic environment this
product may cause radio interference in which case the
user may be required to take adequate measures.
Before connecting other products such as VCR’s and personal•
computers, you should turn off the power of this product for
protection against electric shock.
Do not use attachments not recommended by the•
manufacturer as they may be hazardous.
When replacement parts are required,• be sure the service
technician has used replacement parts specified by the
manufacturer or equivalents. Unauthorized substitutions may
result in fire, electric shock, or other hazards.
Upon completion of any service or repairs to this product,•
ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
Under the following conditions,
1. Turn off the power.
2. Unplug this product from the wall outlet.
3. Refer service to qualified service personnel.
a) When the product emits smoke or unusual smell.
b) When the product exhibits a distinct change in performance
—for example, no picture or no sound.
c) If liquid has been spilled, or objects have fallen on the product.
d) If the product has been exposed to rain or water.
e) If the product has been dropped or damaged in any way.
f) When the power supply cord or plug is damaged.
Do not install this product in the following places:•
in a damp or dusty room–
where the product is exposed to soot or steam, such as–
near the cooking counter or a humidifier
near heat sources–
where condensation easily occurs, such as near the window–
in a location exposed to direct sunlight or strong light–
Do not place this product on an unstable cart, stand, or table.•
The product may fall, causing serious injury to a child or adult,
and serious damage to the product.
The product should be mounted according to the
manufacturer’s instructions, and should use a mount
recommended by the manufacturer.
Do not use this product near water.•
Be sure to install the product in the place where proper•
temperature and humidity are kept (☞“Operating conditions”
on page 28).
This product becomes hot during its use. Take enough care
when handling the product.
CAUTION:
To reduce the risk of electric shock. Do
not remove cover (or back). No user
serviceable parts inside. Refer servicing
to qualified service personnel.
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
The lightning flash with arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
CAUTION
DT-V9L5_EN_1.indb 2DT-V9L5_EN_1.indb 2 10/10/2012 5:18:38 PM10/10/2012 5:18:38 PM

3
Do not use the product for a long time if the sound is distorted.
Do not attempt to service this product yourself, as opening or
removing covers may expose you to dangerous voltages and
other hazards. Refer all service to qualified service personnel.
Use only the power source specified on the unit.
AC power: 120 V, 50 Hz/60 Hz•
DC power: 12 V — 17 V•
The AC power supply is controlled by turning on/off the POWER•
switch on the rear panel. If the product is installed in a place
where you cannot easily turn on/off the POWER switch, control
the AC power supply by plugging/unplugging the power cord
into/from the AC outlet. In this case, install the product as
close to the AC outlet as possible, and leave enough space for
plugging/unplugging the power cord. If the product is installed
in a place where you cannot easily plug/unplug the power
cord, equip an easily accessible device to the wiring of the
building for turning on/off the power.
When the product is left unattended and unused for a long•
period of time, unplug it from the wall outlet and disconnect
the cable system.
Do not overload wall outlets, extension cords, or convenience•
receptacles on other equipment as this can result in a risk of
fire or electric shock.
Use only the accessory cord designed for this product to•
prevent shock.
Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the product and protect it from•
overheating. These openings must not be blocked or covered.
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-circuit the parts,•
which could result in a fire or electric shock.
Never spill liquid of any kind on the product.•
Never place anything on the product. (Placing liquids, naked flames, cloths, paper, etc. on the product may cause a fire.)•
Do not apply any strong shock to the LCD panel. (Do not hit any object against it or push it with a sharp-pointed tool.)•
Do not put heavy objects on the product.•
Do not step on or hang on the product.•
FCC NOTICE
CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE.
WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE
EARTHING CONNECTION.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH
THE SAME OR EQUIVALENT TYPE.
WARNING
To prevent injury by accidental fall
Fix the monitor to a wall by using strings.
Fixing the monitor
Attach the hook (not provided) to the VESA mounting holes on the
rear panel (use the two holes on the upper side) using M4 x 10
mm screws (not provided). Bind the hooks on the rear panel of the
monitor to a wall or a pillar using durable string.
Hook and screw (M4 x 10 mm)
(not provided)
Hook (not provided)
DT-V9L5_EN_1.indb 3DT-V9L5_EN_1.indb 3 10/10/2012 5:18:40 PM10/10/2012 5:18:40 PM

4
Caution for use of the product for many hours
In the case that you use the monitor for many hours, we recommend that you set “No Sync Action” in “Sync Function” to “Power Save” in
Main Menu. This will reduce power consumption and relieve strain on the monitor. To reduce damage to the LCD panel, using the LCD
Saver function is recommended.
Caution for use of the product in the high temperature
Do not use the product in places of high temperature; otherwise, parts of this product or the LCD panel may be damaged. This product is
equipped with a temperature sensor to give warning if the temperature becomes too high. If the temperature exceeds the range of normal
use, “Temp. Over” is displayed, and the power is turned off automatically if the temperature becomes any higher. In this case, move the
product to a place of low temperature to let it cool down.
Maintenance
Unplug this product from the wall outlet before cleaning.
LCD panel
To avoid irreparable change in appearance of the screen such
as uneven color, discoloration, scratches, be careful about the
following:
●Do not paste or stick anything using any glues or adhesive
tapes.
●Do not write anything on the screen.
●Do not strike the screen with a hard object.
●Avoid condensation on the screen.
●Do not wipe the screen with any liquid such as water. In
addition, wiping the screen with water-diluted neutral
detergent or solvent such as alcohol, thinner, or benzine may
affect the anti-reflection treatment of the screen.
●Do not wipe the screen forcefully.
Wipe stains off the LCD panel with a soft cloth. If the screen gets
heavily stained, wipe it with a soft cloth soaked in water-diluted
neutral detergent and wrung well, then wipe with a soft dry cloth.
Cabinet
To avoid the deterioration or damages of the cabinet such as its
paint’s peeling away, be careful about the following:
●Do not wipe the cabinet using solvent such as alcohol, thinner,
or benzine.
●Do not expose the cabinet to any volatile substance such as
insecticides.
●Do not allow any rubber or plastic in contact for a long time.
●Do not wipe the cabinet forcefully.
Wipe stains off the cabinet with a soft cloth. If the cabinet gets
heavily stained, wipe it with a soft cloth soaked in water-diluted
neutral detergent and wrung well, then wipe with a soft dry cloth.
Ventilation openings
Use a vacuum cleaner to get rid of the dust around the intakes (all
the openings). If a vacuum cleaner is not available, use a cloth and
wipe it off. Leaving the dust around the intakes may prevent proper
temperature control and cause damage to the product.
Safety Precautions (cont.)
The LCD panel and backlight have life expectancy. Due to the basic characteristics of the LCD panel, an afterimage or uneven display
may occur. It is recommended that you change images occasionally, activate the power saving function, or often turn off the power to
reduce the load on the LCD panel. Continuous operations of the LCD panel may accelerate the deterioration.
Operating Precautions
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from
the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
16) Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
17) When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries
must be followed strictly.
DT-V9L5_EN_1.indb 4DT-V9L5_EN_1.indb 4 10/10/2012 5:18:40 PM10/10/2012 5:18:40 PM

5
Table of Contents
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFEGUARDS 2
Operating Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Caution for use of the product for many hours 4
Caution for use of the product in the high temperature 4
Maintenance 4
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Adjusting the stand height 6
Tilting the monitor 7
Index of Parts and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Rear panel 8
Front panel 10
Showing Input Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Volume Adjustment/Audio Channel Selection 11
On the Information Display 11
On the Status Display 12
Menu Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
First Time Installation 12
The operation procedure 12
Menu Transition Diagram 13
Main Menu 14
Set-Up Menu 18
External Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
About the external control 23
Using the MAKE/TRIGGER system 23
Using the serial communication 24
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Self-check program 27
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
General 28
LCD panel 28
Input/output terminals 28
Dimensions 29
Available signals 30
DT-V9L5_EN_1.indb 5DT-V9L5_EN_1.indb 5 10/10/2012 5:18:42 PM10/10/2012 5:18:42 PM

6
Installation
●Do not rest your arm on the monitor or lean against the monitor.
●Do not touch the LCD panel when installing the monitor.
●Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor or injury.
Caution
Adjusting the stand height
You can select the stand height according to your preference—higher position or lower position.
To change the stand height, change the position of the screw hole used for attaching the stand.
●When shipped from factory, the stand is attached to the higher position.
●Before adjusting the stand height, set the monitor angle to 0°.
CAUTION
●Lay the monitor on a cloth with the LCD panel facing down to prevent the LCD panel from being damaged.
●Depending on the type of external batteries, the stand cannot be attached or detached when the external battery is attached on the monitor.
●When the stand is attached on the lower position, some types of external batteries cannot be attached to the monitor.
Screw holes for lower position
Guide holes (only for attaching
to the higher position)
Screw holes for higher position
Rear panel of the monitor
Monitor
Attachment screws
Stand
Screw holes for lower position
Higher position
When you want to raise the position of the monitor.
DT-V9L5_EN_1.indb 6DT-V9L5_EN_1.indb 6 10/10/2012 5:18:42 PM10/10/2012 5:18:42 PM

7
Lower position
When you want to lower the position of the monitor.
Attachment screws
Monitor
Stand
Tilting the monitor
You can tilt the monitor as shown below.
About 20°
0°
About 10°
Guidelines
When the monitor is not tilted (0°),
the guidelines align as illustrated.
CAUTION
●Be careful not to pinch your fingers in the gap between the monitor and the stand.
●When the stand is attached to the lower position, you cannot tilt the monitor downward.
●Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor or injury.
DT-V9L5_EN_1.indb 7DT-V9L5_EN_1.indb 7 10/10/2012 5:18:43 PM10/10/2012 5:18:43 PM

8
1POWER switch
Turns AC power on or off.
●You need to press button (☞qon page 10) to use the monitor after turning on the POWER switch.
2AC IN terminal
AC power input connector.
Connect the provided AC power cord to an AC outlet.
●Attach the provided power cord holder to prevent accidental disconnection of the AC power cord. (☞“Attaching the power cord holder”
on page 9)
CAUTION
Do not connect the power cord until all other connections are completed.
3DC switch
Turns the DC power on or off.
●You need to press button (☞qon page 10) on the front panel to turn on the monitor after turning on the DC switch.
●The monitor consumes the battery even while the monitor is on standby. To save battery life, turn off the DC switch.
4DC IN terminal
DC 12 V (maximum DC 17 V) power input connector.
●While using both the AC and DC power supply, AC power supply is preferentially used. If the AC power supply is cut off (for example, when
turning off the POWER switch), the power supply automatically switches to the DC power supply.
●Use a DC power supply with the LPS (Limited Power Sources) function.
5VIDEO/COMPONENT terminals (BNC)
IN: Input terminals for the composite (VBS) and the analog component (Y/PB/PR) signals.
Select the signal type in “Video/Component Select” corresponding to the type of the input signal. (☞page 15)
OUT: Output terminal for the composite (VBS) and the analog component (Y) signals.
6AUDIO (IN) terminal (pin jack)
Input terminal for the analog audio signals.
●Use this terminal for the analog audio connection of the SDI. To select the audio output, set in “Audio Setting” of the Main Menu.
●When you use HDMI input for the picture and analog sound for the audio signal, input analog sound into this terminal, and set in “Audio
Setting” of the Main Menu. (☞page 16)
Rear panel
Index of Parts and Functions
Security slot
Attach a security wire to this slot.
When using DC 12 V power (maximum DC 17 V), check the DC IN terminal pin signal, and use the correct polarity. If the polarity is
reversed, this could cause a fire or personal injury.
Carry handle
Use this handle when carrying the monitor.
DT-V9L5_EN_1.indb 8DT-V9L5_EN_1.indb 8 10/10/2012 5:18:43 PM10/10/2012 5:18:43 PM

9
7HDMI terminal
Input terminal compatible with HDCP for the HDMI signal. (TYPE-A)
8REMOTE terminal
Terminal for controlling the monitor by an external control. (☞“External Control” on page 23)
9 AUDIO (MONITOR OUT) terminals (pin jack)
Output terminals for the analog audio signal.
●The terminals emit the audio signals through the AUDIO (IN) terminal or EMBEDDED AUDIO signals through the E. AUDIO HD/SD SDI (IN 1
or IN 2) input terminal.
● The signal is output from this terminal only when the monitor is on or in “Power Save” (power save) mode (☞“No Sync Action” on page 18).
●The EMBEDDED AUDIO signal...
is decoded into an analog signal, then emitted.–
is emitted only when “SDI 1” or “SDI 2” is selected, and when EMBEDDED AUDIO signals come in to the E. AUDIO HD/SD SDI (IN 1 or IN 2)–
terminal.
●Audio signals are only output from the HDMI terminal when the signals are not protected by HDCP.
Even when the signals are protected by HDCP, sound is emitted from the speakers.–
pE. AUDIO HD/SD SDI (IN 1, IN 2) terminals (BNC)
Input terminals for the HD/SD SDI signals.
●The terminals accept also EMBEDDED AUDIO signals including up to 16 audio channels with a sampling frequency of 48 kHz.
qE. AUDIO HD/SD SDI (SWITCHED OUT) terminal (BNC)
Output terminal for the HD/SD SDI signals.
●The SDI signals of the current input (SDI 1 or SDI 2) are re-clocked, then emitted.
●When an input other than SDI 1 and SDI 2 is selected, the SDI signal of the input selected last time is emitted from this terminal.
●The signals are emitted from this terminal only when the monitor is on or in “Power Save” (power save) mode (☞“No Sync Action” on
page 18)
.
wScrew holes for external battery attachment
Attach external battery for DC power supply by using 2 screw holes. Choose the appropriate screw holes from 1, 2 or 3 according to the type
of external battery. (Depending on the battery type.)
Use the Anton Bauer Dionic 90 (mount: QR DXC-M3A) external battery.
CAUTION
●Do not use the external battery for DC 24 V power supply.
●Use only the battery specified above. If a heavy battery is used, it may fall off depending on the way the monitor is used.
Cover
2
AC IN terminal
Case
1
CAUTION
●Use only the provided screws.
●Make sure the plug will not be pulled out after the cover is attached to the case.
Attaching the power cord holder
The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN terminal.
●The power cord holder consists of two parts, a case and a cover.
To detach the cover
3
Note for connections
Before making any connections, turn off all the equipment.•
Use a cord whose plugs correctly match the terminals on this monitor and the equipment.•
Plugs should be firmly inserted; poor connections could cause noise.•
When unplugging a cord, be sure to grasp its plug and pull it out.•
DO NOT connect the power cord until all connections are complete.•
Refer also to the user manual of each piece of equipment.•
DT-V9L5_EN_1.indb 9DT-V9L5_EN_1.indb 9 10/10/2012 5:18:44 PM10/10/2012 5:18:44 PM

10
Front panel
1Screw holes for attaching protective filter (provided)
Attach the protective filter by using the provided screws.
●Attach the filter to the LCD panel with the frosted side of the
filter facing outwards (when the monitor is shipped from the
factory, protective films are attached to both sides, and a sticker
is attached to the frosted side. Remove the protective films
before use).
CAUTION
●Use only the provided screws to avoid damaging the monitor.
●When attaching the protective filter, do not fasten screws too
tightly; otherwise, the protective filter may be damaged.
2Speaker (monaural)
Outputs the mixed audio of the AUDIO OUT1 terminal and AUDIO
OUT2 terminal. (☞“ 9AUDIO terminals” on page 9)
3Headphones jack (stereo)
Outputs the same audio signal as that output from the
AUDIO(MONITOR OUT) terminals.(☞“ 9AUDIO terminals” on
page 9)
4Picture adjustment knob
PHASE: Adjusts the picture hue.
CHROMA: Adjusts the picture color density.
BRIGHT: Adjusts the picture brightness.
CONTRAST: Adjusts the picture contrast.
●PHASE and CHROMA cannot be adjusted for certain signal
formats.
●When “Component Phase” is set to “Disable” and an NTSC signal
is input, PHASE can be adjusted. (☞page 18)
5MUTING button
Turns off the sound.(muting)
● To cancel the function, press the button again.
●Muting function is also canceled when the volume is adjusted.
(☞page 11)
●Muting function cannot be activated when a menu screen is
displayed.
6/ / / buttons
When a menu screen is displayed selects or adjusts menu items.
(☞“The operation procedure” on page 12)
7SCR. CHK. (Screens check) button/lamp
Displays only the selected element (R, G, B, or the luminance) of
video signal.
●Each time you press this button, the screen changes in the
following order.
Normal screen
Red screenGreen screenBlue screen
Monochrome screen
Index of Parts and Functions (cont.)
“No Effect” is displayed when you press a button which is not•
available for the current input or signal format (the lamp lights
even when the function does not actually work).
The items controlled by the MAKE system cannot be controlled•
by the buttons on the front panel (“Remote On” is displayed
and the lamps do not light).
Tally lamp
This lamp is controlled by the tally function of the MAKE/TRIGGER
terminal.
You can select the color of the tally lamp from “Green” or “Red.”•
You can also select whether the whole lamp is turned on at once,
or whether it is turned on one half at a time. (☞“Tally Setting” in
“Set-Up Menu” on page 18 and “External Control” on page 23)
8MARKER button/lamp
Displays/hides the area marker and the safety marker.
●Select the size and the style of the markers in “Marker” of the
Main Menu (☞page 15).
●The marker is not displayed when it is set to “Off” in “Marker”.
(☞page 15)
9INPUT SELECT buttons/lamps
Selects an input.
SDI 1: E. AUDIO HD/SD SDI (IN 1) terminal
SDI 2: E. AUDIO HD/SD SDI (IN 2) terminal
VIDEO/COMPO. :VIDEO/COMPONENT terminal
HDMI: HDMI terminal
●The lamp for the selected input lights.
pPower lamp
Unlit: The monitor is completely off (the power switch
on the rear panel is turned off).
In Low Power Mode (☞page 22)
Lights in Green: The monitor is on.
Lights in orange: The monitor is off (on standby).
Flashes in orange: The monitor is in the Power Save (power save) mode.
(
☞ “No Sync Action” in “Sync Function” on page 18)
qbutton
Turns on and off (on standby) the monitor.
●The power switch is equipped on the rear panel of the monitor.
(☞1on page 8)
wFUNCTION button
Assign functions to the F1 button when the menu is not displayed.
(☞ page 19)
eVOLUME adjustment button/EMBEDDED AUDIO setting
button
Adjusts the volume when no menu screen is displayed.
Selects an audio channel when EMBEDDED AUDIO signals are
contained in SDI input. (☞“Volume Adjustment/Audio Channel
Selection” on page 11)
rMENU button
Activates/deactivates the display of the Main Menu. (☞“The
operation procedure” on page 12)
tF1 button/lamp
You can use the functions assigned to this button.
HDMISCOPE
INPUT
DT-V9L5_EN_1.indb 10DT-V9L5_EN_1.indb 10 10/10/2012 5:18:44 PM10/10/2012 5:18:44 PM

11
Volume Adjustment/Audio Channel Selection
Volume Adjustment
1When no menu screen is not displayed, press (volume adjustment button)
For SDI input the “Volume/Embedded Audio” screen appears. For any input other than SDI the “Volume”
screen appears.
2Press to move the cursor to “Volume”
(This step is skipped when the ”Volume/Embedded Audio” screen is not displayed.)
3Press to adjust the volume
4Press the MENU button to finish
(The “Volume” screen disappears automatically if no operations are made for 5 seconds.)
Audio Channel Selection
Select the audio channel output from the Speaker (monaural) and AUDIO (MONITOR OUT) (OUT1(L)/OUT2(R))
terminals when an EMBEDDED AUDIO signal is input during SDI input.
●It is necessary to set the audio channel group in advance. (☞”Embedded Audio Group” of “Audio Setting”
on page 16)
●Store the setting for each input of SDI 1 and SDI 2.
●Set “SDI-1 Select” or “SDI-2 Select” to “Auto” or “Digital”.
1When the menu is not displayed, use the buttons
The “Volume/Embedded Audio” screen appears.
●The “Volume/Embedded Audio” screen disappears automatically is no operations are made for about 30 seconds.
2Use the buttons to select the left and right channels (L ch/R ch)
3Use the buttons to select the audio channel
●Each time you press a button the audio channel changes according to the “Embedded Audio Group” setting. (☞page 16)
4Press the MENU button
●The “Volume/Embedded Audio” screen disappears.
On the Information Display
The monitor displays the information below.
●You can set whether the information for each setting is displayed/hidden in the MENU.
1Audio level meter
●You can check the conditions of the EMBEDDED AUDIO signals when “Level Meter Display” is set to “Horizontal” or “Vertical.” (☞“Audio
Setting” on page 16)
●Not displayed when “Level Meter Display” is set to “Off.”
2Signal format
●Displayed when “Status Display” is set to “On” or “Auto.” (☞“Information” on page 20)
●For the contents displayed, see “Available signals” on page 30 and “On the signal format” on page 12.
3Source name assigned in “Character Setting”
●Displayed when “Source ID” is set to “On” or “Auto.” (☞“Information” on page 20)
●Displayed in large letters when “Status Display” is set to “Off” or “Auto.”
4CRC error indication
●Displayed when “CRC Error” is set to “On.” (☞“Information” on page 20)
●A red square is displayed when an error occurs.
5Time code
●When the input signal includes no time code, “TC – –:– –:– –:– –” is displayed. (☞“Information” on page 20)
ySCOPE button/lamp
Displays/hides the indication of the wave form monitor and vectorscope (☞“Scope Setting” on page 17).
●Each time you press this button, the window changes in the following order.
Wave form monitor
Vectorscope
No display
uDC lamp
When the DC power voltage is being lowered due to the battery consumption, the lamp changes to orange from green. When the voltage
becomes lower than a certain level, the monitor automatically turns off and the lamp turns to red.
●Make sure to turn off the POWER switch and DC switch on the rear panel before replacing the battery.
●The length of time that the lamp lights in orange differs depending on the type of battery or the battery condition. It is recommended to
replace the battery when the lamp turns to orange.
9ROXPH

Volume screen
9ROXPH(PEHGGHG$XGLR

*
(PEHGGHG$XGLR/FK
(PEHGGHG$XGLR5FK
9ROXPH

Volume/Embedded Audio screen
Showing Input Signals
Histogram
DT-V9L5_EN_1.indb 11DT-V9L5_EN_1.indb 11 10/10/2012 5:18:46 PM10/10/2012 5:18:46 PM

12
First Time Installation
When you turn on the power and the monitor, “First Time Installation” appears.
Start setting referring to the menu configuration.
For the setting items, see the pages below.
“Language”• ☞ “Language” on page 20
“No Sync Action”• ☞ “Sync Function” on page 18
“No Operation Action”• ☞ “No Operation Action” on page 18
Setting procedure
1Press to move the cursor to the setting item
2Press to select the setting values
●Each time you press one of these buttons, the setting value changes.
3Move the cursor to “Set”
4Press to finish setting
●When you change the settings, a confirmation message appears.
Operate according to directions.
The operation procedure
1Press the MENU button to display the Main Menu
To display the Main Menu
➡Press the MENU button.
To display the Set-Up Menu
➡Press the button while holding the button.
2Use the buttons to select an item and press the button to
proceed to the next screen
3Use the buttons to select an item and press the button to
proceed to the next screen
●For some items, pressing the buttons adjusts the setting.
4Use the buttons to select an item and use the buttons
to adjust the setting
5Press the MENU button to finish operations
●Press the MENU button repeatedly until the menu screen disappears.
On the Status Display
If you press the INPUT SELECT button (☞9on page 10) currently lit, the status of the input signal and setting of MUTING are displayed for about
3 seconds.
●Make the setting to display/hide the status in “Status Display” of the “Information”. (☞page 20)
●When “Status Display” is set to “Auto” or “On,” the status below is also displayed in the following cases:
– When you change the input
– When the signal condition of the current input changes
– When you turn on the monitor
●When “Status Display” is set to “On,” the signal format will remain displayed 3 seconds after the status is
displayed.
1Signal format
●For the contents displayed, see “Available signals” on page 30 and “On the signal format” below.
On the signal format
The following messages appear depending on the type of input signals and their conditions.
When a HDMI signal protected with HDCP is input
When no video signal comes in
When a noncompliant video signal comes in
“*” (at the end of the indication)➔
“No Sync”➔
“Out of range”➔
2Signal format of HDMI and VIDEO/COMPONENT input
3Setting of “MUTING”
• Only appears when in mute mode. (☞5on page 10).
Showing Input Signals (cont.)
Main Menu
Selected item
Operation guide
Set-Up Menu
Ex.: When “Picture Function”
in the Main Menu is selected
Menu Configuration
●The menu screen disappears automatically if no operations are
made for about 30 seconds.
●Inoperable menus will be grayed out.
●Some items will not be displayed on the menu depending on the
selected input and signal format.
(KTUV6KOG+PUVCNNCVKQP
1HH
'PINKUJ
1HH
.CPIWCIG
0Q5[PE#EVKQP
0Q1RGTCVKQP#EVKQP
5GV
●Once the settings have been adjusted, this screen will not appear
again.
●The settings can be changed afterwards in Main Menu and Set-Up
Menu.
/CKP/GPW
2KEVWTG(WPEVKQP
5K\G2QUKVKQP#FLWUV
#URGEV
5KIPCN5GVVKPI
/CTMGT
#WFKQ5GVVKPI
5EQRG5GVVKPI
0Q1RGTCVKQP#EVKQP 1HH
5[PE(WPEVKQP
&[PCOKE
6HW8S0HQX
)XQFWLRQ6HWWLQJ
$OO/RFN
(QJOLVK
3LFWXUH6XE$GMXVW
:KLWH%DODQFH6HWWLQJ
5HPRWH6HWWLQJ
,QIRUPDWLRQ
&RQWURO/RFN
/DQJXDJH
,0'
DOOUHVHW
E^XijgZ;jcXi^dc
/"'%
/D[[
/%,
/CdgbVa
/=VgY
/'#'
/.(%%@
7VX`a^\]i
6eZgijgZ
6eZgijgZAZkZa
8I>
AI>
<VbbV
8dadgIZbeZgVijgZ
hjWbZcj
gZhZi
/CKP/GPW
2KEVWTG(WPEVKQP
5K\G2QUKVKQP#FLWUV
#URGEV
5KIPCN5GVVKPI
/CTMGT
#WFKQ5GVVKPI
5EQRG5GVVKPI
0Q1RGTCVKQP#EVKQP 1HH
5[PE(WPEVKQP
&[PCOKE
DT-V9L5_EN_1.indb 12DT-V9L5_EN_1.indb 12 10/10/2012 5:18:47 PM10/10/2012 5:18:47 PM

13
Menu Transition Diagram
Main Menu
Picture Function
Audio Setting
Sync Function
No Operation Action
Signal Setting
Marker
Aspect
Backlight
Aperture
Aperture Level
CTI
LTI
Gamma
Color Temperature
sub menu
reset
Level Meter Display
Channel Arrange
Position
Meter Type
Reference Level
Over Level
Transparent
Peak Hold
H Size
H Position
V Size
V Postion
sub menu
reset
Video/Component Select
I/P Mode
Color System
sub menu
reset
Area Marker
Marker Aspect
Safety Marker
Safety Area
Frame
Center Marker
Line Brightness
R-Area Marker
R-Marker Aspect
R-Safety Marker
R-Safety Area
Auto Aspect
Manual Aspect
SD4：3 Size
16：9 Size
1：1
SDI-1 Select
SDI-2 Select
HDMI Select
Video/Component Select
Embedded Audio Group
Level Meter Setting
No Sync Action
Delay Time
Low Latency
Size/Position Adjust
Dynamic
Scope Setting
Gain
Size
Position
Transparent
Auto Off
Histogram Display
Wave Display
Wave Filter
Wave Over Level Marking
Wave Over Level
Set-Up Menu
Contrast
Bright
Chroma
Phase
NTSC Setup
Component Level
sub menu
reset
Color Temperature*
R Drive
G Drive
B Drive
R Cut Off
G Cut Off
B Cut Off
sub menu
reset
Function Setting
Picture Sub Adjust
White Balance Setting
Remote Setting
Information
Control Lock
Language
IMD
all reset
sub menu Position
Tally Setting
Dimmer
Component Phase
Remote Active On Standby
LCD Saver
Function Key Setting Setting
Execute
Cancel
Status
Start After
Tally Type
Tally Color
1st Start
Work Time
Contrast
Backlight
OSD Contrast
Side Mask
reset
Parallel Type
Pin1
Pin2
Pin3
Pin4
Pin5
Pin6
Pin7
Pin8
Source ID
Character Setting
Status Display
Time Code
Time Code Select
CRC Error
Sub Hour Meter
Model
Version
Hour Meter
IMD Display
IMD Protocol
Address
IMD Size
Text Color
Tally 1 Color
Tally 2 Color
Background Color
reset
Function 1
Function Display
* : "Color Temperature" is only displayed, and cannot be set/changed.
DT-V9L5_EN_1.indb 13DT-V9L5_EN_1.indb 13 10/10/2012 5:18:49 PM10/10/2012 5:18:49 PM

14
Menu Configuration (cont.)
Main Menu
Picture Function
Setting for the picture quality.
Item To do Setting value
Backlight Adjusts the brightness of the display. –20 to +20
Aperture*1Activates/deactivates the function at the level set in “Aperture Level”. Off, On
Aperture Level*1Compensate the frequency response of the luminance signal of the video signal. 01 to 10
CTI Adjust the clearness of the outlines of the chrominance signal. Off, Normal, Hard
LTI Adjust the clearness of the outlines of the luminance signal. Off, Normal, Hard
Gamma Select the Gamma correction value. 2.2 (equivalent to Υ 2.2),
2.35 (equivalent to Υ 2.35),
2.45 (equivalent to Υ 2.45),
2.6 (equivalent to Υ 2.6)
Color Temperature Select the color temperature. 9300K, 6500K, User
sub menu Display the sub menu which enables you to adjust the items in “Picture Function” while viewing the actual picture.
reset Restore the default settings for all the items in “Picture Function”.
*1Memorized for each input.
Size/Position Adjust
Adjusts the size and position of the picture.
Item To do Setting value
H Size*1Adjust the horizontal picture size.
Setting value varies
depending on the signals.
H Position*1Adjust the horizontal picture position.
V Size*1Adjust the vertical picture size.
V Position*1Adjust the vertical picture position.
sub menu Display the sub menu which enables you to adjust the items in “Size/Position Adjust” while viewing the actual picture.
reset Restore the default settings for all the items in “Size/Position Adjust”.
*1Memorized for each signal format.
Aspect
Sets the aspect ratio of the screen for displaying videos.
Item To do Setting value
Auto Aspect Select whether to adjust the aspect ratio (horizontal to vertical ratio of the screen) of the SD
signal automatically or manually (Manual Aspect). Off, On
Manual Aspect*1Sets the aspect ratio (horizontal to vertical ratio of the screen) of the SD signal. 16:9, 4:3
SD4:3 Size*1,*2Selects the picture size when the input signal format is 4:3.
Normal, H Full, V Full
Normal : Matches the vertical picture size to the number of pixels.
H Full : Matches the horizontal picture size to the horizontal size of the screen. At
this time, the top and bottom of the picture are overscanned.
V Full : Enlarges the picture vertically. At this time, the right and left of the
picture are overscanned.
16:9 Size*1,*2Selects the picture size when the input signal format is 16:9.
Normal, V Full
Normal : Matches the vertical picture size to the number of pixels.
V Full : Enlarges the picture vertically. At this time, the right and left of the
picture are overscanned.
1:1*3Displays the picture in the original resolution of the input signal.
•The aspect ratio of the picture may change depending on the input signal. Off, On
*1Not activate when picture is displayed in the 1:1 mode.
*2When the histogram, wave form monitor or vector scope is displayed, only "Normal" is available.
*3When the histogram, wave form monitor or vector scope is displayed, only "Off" is available.
Dynamic Setting values: Off, On
Adjusts the picture to be suitable for a bright place.
•When the function is turned on:
- “Backlight” and “Picture Sub Adjust” are grayed out and cannot be operated.
- The setting of “Backlight” is ineffective.
DT-V9L5_EN_1.indb 14DT-V9L5_EN_1.indb 14 10/10/2012 5:18:49 PM10/10/2012 5:18:49 PM

15
Signal Setting
Settings for input signals.
Item To do Setting value
Video/Component Select Selects the signal type you want to use for VIDEO/COMPONENT terminals. Video, Component
I/P Mode Selects a proper mode corresponding to the input picture. Normal, Cinema
Color System Select the color system. Auto, NTSC, PAL, SECAM,
NTSC 4.43, PAL-M, PAL-N,
PAL60
•If the picture is unstable with “Auto,” select the color system according to the input signal.
sub menu Display the sub menu which enables you to adjust the items in “Signal Setting” while viewing the actual picture.
reset Restore the default settings for all the items in “Signal Setting”.
Marker*1
Settings for marker functions.
Item To do Setting value
1/2 Area Marker Activate/deactivate the area marker and select the style of it.
The setting values and features are as follows.
Off, Line, Half, Half+Line
Off
Line
Half
Half+Line
:
:
:
:
Deactivate the marker.
Displays the area with an outline.
The area outside the specified aspect ratio of the screen is displayed at 50%
transparency.
The area of the specified aspect ratio of the screen is indicated by an outline,
and the area outside of that is displayed at 50% transparency.
Marker Aspect Select the aspect ratio of the area marker. 4:3, 16:9, 14:9, 13:9, 2.35:1,
1.85:1, 1.75:1, 1.66:1
Safety Marker Activate/deactivate the safety marker and select the style of it.*2Off, Line, Half, Half+Line
Safety Area Adjust the area of the safety marker. 80% to 100%
Frame*3Displays/Hides the video area. Off, On
Center Marker*3Displays/hides the marker indicating the center position of the picture. Off, On
Line Brightness Adjust the brightness of the marker. Low, High
2/2 R-Area Marker Activate/deactivate the area marker and select the style of it.*2
Off, Line, Half, Half+Line
R-Marker Aspect Select the aspect ratio of the area marker. 4:3, 16:9, 14:9, 13:9, 2.35:1,
1.85:1, 1.75:1, 1.66:1
R-Safety Marker Activate/deactivate the safety marker and select the style of it.*2
Off, Line, Half, Half+Line
R-Safety Area Adjust the area of the safety marker. 80% to 100%
●The area marker or the safety marker is displayed by using MARKER button or external control.
●“R” means “REMOTE (External control)”. Select either non-“R-” items or “R-” items to activate by using external control. (☞“External Control” on
page 23)
●When a picture is displayed in 4:3 aspect ratio, the safety marker for the 4:3 area is displayed.
●To display the safety marker for the area of a picture displayed in 16:9 aspect ratio, set Area Marker to "Off".
*1Memorized for each signal format.
*2The setting values are the same as that of “Area Marker”.
*3In 1:1 mode, this display is grayed out and cannot be operated.
DT-V9L5_EN_1.indb 15DT-V9L5_EN_1.indb 15 10/10/2012 5:18:50 PM10/10/2012 5:18:50 PM

16
Menu Configuration (cont.)
Audio Setting
Settings for EMBEDDED AUDIO signals and audio level meter signal.
Item To do Setting value
SDI-1 Select
SDI-2 Select
Select the input through which audio is output. Off, Auto, Digital, Analog
Off
Auto
Digital
Analog
:
:
:
:
Does not output audio.
Output digital audio prior to analog audio.
Output audio from the SDI terminal.
Output audio from the AUDIO IN terminal.
HDMI Select Select the input through which audio is output. Off, Digital, Analog
Off
Digital
Analog
:
:
:
Does not output audio.
Output audio from the HDMI terminal.
Output audio from the AUDIO IN terminal.
Video/Component Select Select the input through which audio is output. Off, Analog
Off
Analog
:
:
Does not output audio.
Output audio from the AUDIO IN terminal.
Embedded Audio Group*1Select the audio channel group of the EMBEDDED AUDIO signals.
The setting values and selectable audio channels of EMBEDDED AUDIO signals are as follows.
(G means GROUP)
1G, 2G, 1-2G ,3G, 4G, 1-4G,
3-4G
1G
2G
1-2G
3G
4G
1-4G
3-4G
:
:
:
:
:
:
:
channel(s) 1/2/3/4/1+2/3+4/1 – 4 (1G)
channel(s) 5/6/7/8/5+6/7+8/5 – 8 (2G)
channel(s) 1/2/3/4/5/6/7/8/1+2/3+4/5+6/7+8/1 – 4 (1G)/5 – 8 (2G)/
1 – 8 (1G+2G)
channel(s) 9/10/11/12/9+10/11+12/9 – 12 (3G)
channel(s) 13/14/15/16/13+14/15+16/ 13 - 16(4G)
channel(s) 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16/1+2/3+4/
5+6/7+8/9+10/11+12/13+14/15+16/1–4(1G)/5–8(2G)/9–12(3G)/13-16(4G)/
1–8(1G+2G)/1-16(1-4G)
channel(s) 9/10/11/12/13/14/15/16/9+10/11+12/ 13+14/15+16/ 9 –12 (3G)/
13-16(4G)/9-16(3-4G)
Level Meter Setting*1Specify the audio level meter display for EMBEDDED AUDIO signal.
Example of audio level meter display - Connection between the level meter position and channel
Ex: When “Horizontal” is selected for “Level Meter Display”: Ex: When “Vertical” is selected for “Level Meter Display”:
-10dB -20dB-20dB -10dB
-20dB
-10dB
-20dB
-10dB
•The number of audio channels displayed on the level meter varies depending on the setting value of “Embedded Audio
Group”.
•The audio level meter can be displayed at the top or bottom of the screen.
•When “On” is selected for “Peak Hold”, the maximum value is retained a certain period when the signal level becomes
maximum.
Level Meter Display Select the status of the level meter (display vertically, horizontally, or not displayed). Off, Vertical, Horizontal
Channel Arrange Select how the audio channels are displayed on the level meter. Line, Divide
Position Adjust the vertical level meter position. Upper, Lower
Meter Type Specify the design of the level meter. Bar, Block
Reference Level Select the standard input level indicated on the level meter. –20dB, –18dB
Over Level Select the input level’s lower limit indicated in red. –10dB, –8dB, –6dB, –4dB,
–2dB
Transparent Adjust the transparency of the level meter display against the image. Off, Background, All
Peak Hold Activates/deactivates the peak hold function of the level meter. Off, On
*1Memorized for each input.
Green
REFERENCE
LEVEL
OVER LEVEL
Red
Yellow
OVER LEVEL
REFERENCE LEVEL
DT-V9L5_EN_1.indb 16DT-V9L5_EN_1.indb 16 10/10/2012 5:18:51 PM10/10/2012 5:18:51 PM

17
Scope Setting*1
Configure the settings for the wave form monitor and vector scope.
Item To do Setting value
Gain*2Adjust the input gain level. –10 to +10
Size*3Set the window size. Normal, Large
Position Select the window position. Lower Right, Lower Left
Upper Left, Upper Right
Transparent Activates/deactivates the function to make the window translucent. Off
On
Off
On
:
:
Normal
Translucent
Auto Off Set the function to turn off the window automatically 15 minutes after displayed. Off, On
Histogram Display Select the signal component for the histogram display. Y, R, G, B
Wave Display Select a wave form to be displayed for the wave form monitor. Y, Pb, Pr (HD signal)
Y, Cb, Cr (SD signal)
R, G, B (RGB signal)
Wave Filter Turn on/off the lowpass filter to put over the input wave form data. Flat (No filter)
Lowpass
Wave Over Level Marking Turn on/off the function to change the wave form color of signals over the value
specified in “Wave Over Level”. (☞below)
Off, On
Wave Over Level Adjust the lower limit for the over level. 70 – 109
Example of the histogram display
Example of the wave form monitor
Ex.: When the luminance signal is Y, “Wave Over Level Marking” is set to “On” and
“Wave Over Level” is set to “80”
Example of the vector scope
Ex.: When the color bar is
displayed
• The wave form color of signals over the value specified in “Wave Over Level”
turns red.
• The display differs depending on the input signal or the “Wave Display” setting.
*1The vector scope is not displayed when the input signals are RGB.
*2Unavailabe for the histogram.
*3Only “Normal” is available for the histogram.
Start End
Red White
Y
Image signals
DT-V9L5_EN_1.indb 17DT-V9L5_EN_1.indb 17 10/10/2012 5:18:51 PM10/10/2012 5:18:51 PM

18
Menu Configuration (cont.)
Sync Function
Settings for the synchronization with signals.
Item To do Setting value
No Sync Action Select the screen status when no signal is coming in. Off, Standby, Power Save
(power save mode),
Gray Back (gray screen)
Delay Time Select the period until the screen status changes as selected in “No Sync Action” after signals
stop coming in.
30s, 5min, 15min
Low Latency Activates/deactivates the function to shorten the time taken to display the picture (low
latency function).
Off, On
•If the picture is not displayed steadily while “On” is selected, select “Off.”
•While “On” is selected, the displayed picture may become unstable when an operation
using buttons on the front panel or the menu is performed, or when the signal format
changes.
●When setting “No Sync Action” to “Gray Back,” the screen color changes to gray and the power consumption of the backlight is saved by half.
Selecting “Power Save” (power save mode) saves more power consumption by turning off the backlight.
No Operation Action Setting values: Off, On
Setting of the function for turning the unit off (standby) automatically when no operations are made for more than 4 hours.
Off: Does not turn off automatically
On: Turns off automatically
●When the function is turned On, a warning message will be displayed about 3 minutes before turning off automatically.
When you turn on the unit with the function turned On, a message notifying that the setting is turned on will be displayed for about 30
seconds.
Set-Up Menu
Function Setting
Settings for the sub menu display, color of the tally lamp, and the intensity of the button lamps.
Item To do Setting value
sub menu Position Select the contents and displaying position of “sub menu.”
The setting values and features are as follows.
Lower1, Upper1, Lower2,
Upper2
Lower1 :Displays the current setting and adjustment bar at the lower part of the screen.
Upper1 :Displays the current setting and adjustment bar at the upper part of the screen.
Lower2 :Displays the current setting at the lower part of the screen.
Upper2 :Displays the current setting at the upper part of the screen.
•The adjustment bar is not displayed for some items.
Tally Setting
Set the color and mode of the tally lamp using external control.
Tally Type Normal
Half
:
:
Light up the entire tally.
Light up the left and right halves of the tally individually. Normal, Half
Tally Color Set the tally color when “Tally Type” is set to “Normal”. Green, Red
Dimmer Select the intensity of the button lamps. Normal, Dark
Component Phase Deactivates the function of PHASE adjustment (Picture adjustment knob and “Picture Sub
Adjust” in Set-Up Menu) except when an NTSC signal comes in (☞on page 19).
Enable, Disable
Remote Active On
Standby
Set the conditions for the power switch by external control (serial). Off, On
Off
On
:
:
Cannot power on by external control after powered OFF.
Can power on by external control after powered OFF.
LCD Saver Configure the setting for reducing damage to the LCD panel for long-time use. (☞on page 22)
Setting 1st Start Set the standby time. (unit: hours) 00h-24h
Work
Time
Set the time for performing the function. (unit: hours) 01h-06h
Contrast Set the contrast reduction. Normal, Save
Backlight Reduce the backlight brightness. Normal, Save
OSD
Contrast
Set the contrast reduction of the OSD display. Normal, Save
Side Mask Select whether to use the side panel.
*The Side Mask function works no matter whether the LCD Saver is active or stopped. Off, On
reset Restore the default settings for all the items in “LCD Saver”.
Execute Execute the LCD Saver function.
Cancel Stop the LCD Saver function. (“Cancel” will be grayed out during the function stop.)
Status Display the LCD Saver status. Off, Ready
Start After Stop the LCD Saver function. (unit: hours and minutes) **h **min
DT-V9L5_EN_1.indb 18DT-V9L5_EN_1.indb 18 10/10/2012 5:18:52 PM10/10/2012 5:18:52 PM

19
Function Key Setting Specify the function assigned to the F1 button.
Function1 Specify the function assigned to the F1 button.
* See pages 13 to 22 for details of the functions assigned to Function 1.
- - -, Aperture,
I/P Mode,
Frame, Center Marker,
Level Meter Display,
Gamma, Color
Temperature,
CRC Error, Manual Aspect,
Time Code, 1:1, Dynamic
Function Display Select whether to display the status of the assigned function when you press the F1 button. Off, Mode-1, Mode-2
Off
Mode-1
Mode-2
:
:
:
No status display. Perform the registration function.
Display the status. Perform the registration function.
Display the status. Do not perform the registration function.
Perform the registration function when the status is displayed and the button is
pressed again.
●To display the “Function Key Setting” menu, press the button when the menu is not displayed.
●About the operations of F1 button
Each time you press the button, the setting value for the assigned function changes in order.
Ex: When “Color Temperature” is assigned
Each time you press the button, three setting values alternate.
Picture Sub Adjust
Configure the standard level of image adjustment.
Item To do Setting value
Contrast*1Adjust the standard level for the contrast adjusted with the CONTRAST knob on the front
panel.
–20 to +20
Bright*1Adjust the standard level for the brightness adjusted with the BRIGHT knob on the front
panel.
–20 to +20
Chroma*1Adjust the standard level for the chroma adjusted with the CHROMA knob on the front panel. –20 to +20
Phase*1,*2Adjust the standard level for the phase adjusted with the PHASE knob on the front panel. –20 to +20
NTSC Setup Select the set-up level of the input NTSC signal. 00 (compliant with 0 %
set-up signal), 7.5 (compliant
with 7.5 % set-up signal)
Component Level Select the level of the analog component signal (480i and 576i only). B75 (compliant with
BetacamVTR 7.5 % set-up
signal), B00 (compliant with
BetacamVTR 0 % set-up
signal), SMPTE (compliant
with M2VTR signals)
sub menu Display the sub menu which enables you to adjust the items in “Picture Sub Adjust” while viewing the actual picture.
reset Restore the default settings for all the items in “Picture Sub Adjust”.
*1Memorized for each input.
*2When “Component Phase” (☞page 18) is set to “Disable,” “Phase” cannot be adjusted if no NTSC signal is input.
White Balance Setting
Display the color temperature, and adjusts the drive level and cutoff point of each color (R/G/B).
Item To do Setting value
Color Temperature Select the color temperature. (Cannot be set/changed) 9300K, 6500K, User
R Drive *1
G Drive
B Drive
Adjust the drive level of each color (red, green, and blue).
●The maximum (Max) and minimum (Min) values vary depending on the input signal or
other settings.
Min – 000 – Max
(in 1024 grades)
R Cut Off *1
G Cut Off
B Cut Off
Adjust the cutoff point of each color (red, green, and blue).
●The maximum (Max) and minimum (Min) values vary depending on the input signal or
other settings.
Min – 000 – Max
(in 1024 grades)
sub menu Display the sub menu which enables you to adjust the items in “White Balance Setting” while viewing the actual picture.
reset Restore the default settings for all the items in “White Balance Setting”.
*1Memorized for each color temperature.
DT-V9L5_EN_1.indb 19DT-V9L5_EN_1.indb 19 10/10/2012 5:18:53 PM10/10/2012 5:18:53 PM

20
Remote Setting
Settings for the external control.
Item To do Setting value
Parallel Type Select a control method of the MAKE/TRIGGER terminal. Make, Trigger, Set
Pin1
Assign the control functions to the pins of the MAKE/TRIGGER terminal.
•Assign a function to each pin terminal by selecting “Set” in “Parallel Type” mentioned
above.
☞"Display" in "Functions
controlled by the MAKE/
TRIGGER system" on page 24
Pin2
Pin3
Pin4
Pin5
Pin6 The functions are assigned for “Pin6” – “Pin8” and you cannot change the assignment of
these functions.
Tally
Pin7 Enable
Pin8 GND
Information
Settings for the information display of the monitor.
Item To do Setting value
Source ID Select whether the name assigned in “Character Setting” (☞below) is displayed on the
screen (☞“On the Information Display” on page 11).
•When “Auto” is selected, the display color synchronizes with the color of the tally lamp
while the tally lamp is lit.
Off, On, Auto
Character Setting Assign a name to each video source as you like (10 characters at maximum). You can also enter a name using the RS-232C
system. (☞Page 22)
Status Display Display/Hide the status of the current input and the setting of MUTING. (☞"On the Status
Display" on page 12)
Auto, Off, On
Time Code Display/Hide the Time Code. Off, On
Time Code Select Select the type of the TIME CODE display.
VITC*1, LTC*1, D-VITC
CRC Error Display/Hide the CRC error when the HD SDI signal is input. (☞"On the Information Display"
on page 11)
Off, On
Sub Hour Meter Display the hours of use (unit: hour). The usage time can be reset to 0.
Model Display the model name of the monitor.
Version Display the version of the monitor.
Hour Meter*2Display the total hours of use (unit: hour). This item is used for maintenance of the monitor. You cannot reset this item.
*1Ancillary time code
*2”Hour Meter” and settings specified using the Picture adjustment knob (☞4 on page 10) are not reset.
Control Lock*3Setting values: Off, Volume Lock, All Lock
Settings for disabling the buttons on the front panel.
*3•The following operations are not available when “Volume Lock” is selected.
- Picture adjustment knob
•The “All Lock” function disables to control the buttons on the front panel. But following operations are available.
- Turning on/off (on standby) the monitor
- Displaying the Set-Up Menu by pressing button while holding button and turning “Control Lock” to “Off”
- Operating the monitor by an external control
If you try other operations, “Control lock on!” appears on the screen.
Language Setting values: English, Deutsch, Français, Español, Italiano, Pуccкий
Select the displayed language for the menu, etc.
Menu Configuration (cont.)
DT-V9L5_EN_1.indb 20DT-V9L5_EN_1.indb 20 10/10/2012 5:18:53 PM10/10/2012 5:18:53 PM