JVC RX-6010VBK User manual

SERVICE MANUAL
AUDIO/VIDEO CONTROL RECEIVER
No.20909
Feb. 2001
COPYRIGHT 2001 VICTOR COMPANY OF JAPAN, LTD.
RX-6010VBK
RX-6018VBK
RX-6010VBK/6018VBK
J U.S.A.
Area Suffix
Contents
Safety precautions --------------------------------------------------------1-2
Importance administering point on the safety ----------------------1-3
Disassembly method -----------------------------------------------------1-4
Adjustment method -------------------------------------------------------1-9
Description of major ICs -------------------------------------------------1-10
DIGITAL
1
7
1
REMOTE CONTROL
SURROUND
SURROUND
MODE
SOUND
TV/VIDEO CD-DISC
15
– SUBWOOFER +TEST
6
54
EFFECT – CENTER +
5
98
– REAR•L +–VCR CH +
5
TV VCR AUDIO SLEEP
+10 10
–REAR•R +
MENU
ENTER
5
TAPE/CDR FM/AM
MUTING
CD
TV SOUND VCR ANALOG/DIGITAL
TV VOL
TV CH
DVD
––
++
VOLUME
£
POWER
8
+
–
7/P
RM-SRX6010J
A/V CONTROL RECEIVER
32
DVD VCR TV SOUND
ADJUST
AUDIO/VIDEO CONTROL RECEIVER
SETTING
MASTER VOLUME
CONTROL
DOWN UP
CD TAPE/CDR
SOURCE NAME
INPUT DIGITALINPUT ANALOG
SPEAKERS ON/OFF
DSP MODE
PHONES
SURROUND ON/OFF
FM/AM TUNING
STANDBY
POWER
FM/AM PRESET FM MODE
MEMORY
INPUT ATT
FM/AM
DIGITAL
DIGITAL
SURROUND
RX-6018 is packaging model.
With SX-XSW350,SX-XSW450
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-2
1. This design of this product contains special hardware and many circuits and components specially
for safety purposes. For continued protection, no changes should be made to the original design
unless authorized in writing by the manufacturer. Replacement parts must be identical to those
used in the original circuits. Services should be performed by qualified personnel only.
2. Alterations of the design or circuitry of the product should not be made. Any design alterations of
the product should not be made. Any design alterations or additions will void the manufacturer`s
warranty and will further relieve the manufacture of responsibility for personal injury or property
damage resulting therefrom.
3. Many electrical and mechanical parts in the products have special safety-related characteristics.
These characteristics are often not evident from visual inspection nor can the protection afforded
by them necessarily be obtained by using replacement components rated for higher voltage,
wattage, etc. Replacement parts which have these special safety characteristics are identified in
the Parts List of Service Manual. Electrical components having such features are identified by
shading on the schematics and by ( ) on the Parts List in the Service Manual. The use of a
substitute replacement which does not have the same safety characteristics as the recommended
replacement parts shown in the Parts List of Service Manual may create shock, fire, or other
hazards.
4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the
like to be separated from live parts, high temperature parts, moving parts and/or sharp edges
for the prevention of electric shock and fire hazard. When service is required, the original lead
routing and dress should be observed, and it should be confirmed that they have been returned
to normal, after re-assembling.
5. Leakage currnet check (Electrical shock hazard testing)
After re-assembling the product, always perform an isolation check on the exposed metal parts
of the product (antenna terminals, knobs, metal cabinet, screw heads, headphone jack, control
shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.
Do not use a line isolation transformer during this check.
Plug the AC line cord directly into the AC outlet. Using a "Leakage Current Tester", measure
the leakage current from each exposed metal parts of the cabinet , particularly any exposed
metal part having a return path to the chassis, to a known good earth ground. Any leakage
current must not exceed 0.5mA AC (r.m.s.)
Alternate check method
Plug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms
per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by
a 0.15 F AC-type capacitor between an exposed
metal part and a known good earth ground.
Measure the AC voltage across the resistor with the
AC voltmeter.
Move the resistor connection to eachexposed metal
part, particularly any exposed metal part having a
return path to the chassis, and meausre the AC
voltage across the resistor. Now, reverse the plug in
the AC outlet and repeat each measurement. voltage
measured Any must not exceed 0.75 V AC (r.m.s.).
This corresponds to 0.5 mA AC (r.m.s.).
1. This equipment has been designed and manufactured to meet international safety standards.
2. It is the legal responsibility of the repairer to ensure that these safety standards are maintained.
3. Repairs must be made in accordance with the relevant safety standards.
4. It is essential that safety critical components are replaced by approved parts.
5. If mains voltage selector is provided, check setting for local voltage.
Good earth ground
Place this
probe on
each exposed
metal part.
AC VOLTMETER
(Having 1000
ohms/volts,
or more sensitivity)
1500 10W
0.15 F AC TYPE
!Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-3
Caution: For continued protection against risk of
fire, replace only with same type 6.3A/125V for
F201, 2A/125V for F202 and F203. This symbol
specifies type of fast operating fuse.
Precaution: Pour eviter risques de feux, remplacez
le fusible de surete de F201 comme le meme type
que 6.3A/125V, et 2A/125V pour F202 et F203.
Ce sont des fusibles suretes qui functionnes rapide.
^
Importance administering point on the safety
FC211
FC212
R1
EP1
B106
B105
B104
TA201
TA202
PW104
PW102
PW105
PW103
PW101
B103
B102
B101
B108
B107
B109
B110
CN251
D205
FC221
FC222
FC231
FC232
R201
RY201
110
111 112113 114120 121
122 130131
B192
B191
B160
B159
6.3A-125V
2A-125V
2A-125V
F 201
F 203
F 202
LVA1029-A9
LVA1029-A7
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-4
Remove the four screws A attaching the top cover
on both sides of the body.
Remove the three screws B on the back of the body.
Remove the top cover from behind in the direction of
the arrow while pulling both sides outward.
1.
2.
3.
Disassembly method
Removing the top cover (See Fig.1)
Prior to performing the following procedure, remove
the top cover.
Remove the power cord stopper from the rear panel
by moving it in the direction of the arrow.
Remove the seventeen screws E attaching the each
boards to the rear panel on the back of the body.
Remove the four screws F attaching the rear panel
on the back of the body.
1.
2.
3.
Removing the rear panel (See Fig.4)
Prior to performing the following procedure, remove
the top cover.
Disconnect the card wire from connector CN402 on
the audio board and CN201 on the power supply
board in the front panel assembly.
Cut off the tie band fixing the harness.
Remove the three screws C attaching the front
panel assembly.
Remove the four screws D attaching the front panel
assembly on the bottom of the body. Detach the front
panel assembly toward the front.
1.
2.
3.
4.
Removing the front panel assembly
(See Fig.2 and 3)
Fig.1
Fig.2
Fig.3
Fig.4
A 2
A 2
B
Top cover
C
Power supply
board
Audio board
CN402
Main
board
Tie band
D
E
E
F
E
E
F
F
Cord stopper
C
Front panel assembly
Front panel assembly
D
Rear panel
CN201
F
E
E
E
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-5
Prior to performing the following procedure, remove
the top cover and the rear panel.
Cut off the tie band fixing the harness.
Disconnect the DSP board from connector CN481 on
the audio board.
Disconnect the audio input board. DVD board and
the video board from connector CN421, CN431 and
CN441 on the audio board.
Disconnect the tuner board from connector CN411
on the audio board.
1.
2.
3.
4.
Removing each board connected to the
rear side of the audio board
(See Fig.5 to 8)
Fig.5
Fig.6
Fig.7
Fig.8
CN411
Tie band
DSP
board
DVD
board Video
board
Tuner
board
Audio
input
board
DSP board
CN481
CN441
CN431
CN421
CN481
CN421
CN431 CN441
CN411
Tie band
CN421 CN431 CN441
Audio
input
board
DVD
board Video
board
Tuner
board
Audio
board
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-6
Prior to performing the following procedure, remove
the top cover and the rear panel.
Removing the audio board
(See Fig.9)
Disconnect the card wire from connector CN402 on
the audio board.
Disconnect the relay board from the audio board and
the power supply board. (CN291,CN491)
Disconnect the harness from connector CN473,
CN471, CN472, and CN385.
Remove the three screws G attaching the audio
board assembly.
Remove the screw H attaching the audio board
assembly.
1.
2.
3.
4.
5.
Remove the ten screws K and four screws L
attaching the heat sink.
Remove the two screws L' attaching the heat sink
from the rear side of main board.
1.
2.
Removing the Heat sink
(See Fig.11 to 12)
Prior to performing the following procedure, remove
the top cover, the rear panel and audio board.
Disconnect the harness from connector CN241 and
CN203 on the power supply board respectively.
Remove the four screws I and the two screws J
attaching the main board.
1.
2.
Removing the main board.
(See Fig.10)
Fig.9
Fig.10
Fig.11
Fig.12
power
supply
board
Power / Fuse
board
Relay board
CN473
Audio board
Main board
rear side
Main
board
Heat sink
CN291
CN203
CN491 H
G
CN471 CN385
CN402
CN472
Power
transformer
G
G
CN241
I
I
II
JJ
LL
KKK
L'
L'
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-7
Prior to performing the following procedure, remove
the top cover and the rear panel.
Remove the screw N attaching the power / fuse
board.
Unsolder the power cord and other harnesses
connected to the power / fuse board.
1.
2.
Removing the power / fuse board
(See Fig.13)
Prior to performing the following procedures, remove
the top cover.
Unsolder the two harnesses connected to the power
transformer.
Disconnect the harness from connector CN251 and
unsolder the harnesses connected to FW201 on the
power transformer board.
Remove the four screws M attaching the power
transformer.
1.
2.
3.
Removing the power transformer
(See Fig.13)
Prior to performing the following procedure, remove
the top cover and the front panel.
Remove the one nut attaching the headphone jack of
the power supply board on the front side of the body.
Disconnect the harness connected to connector
CN241,CN201,CN203 and CN291 on the power
transformer board (If necessary, cut off the band
fixing the harness on the side of the base chassis).
Remove the three screws O attaching the power
supply board and pull out the power supply board
from the front bracket backward.
Unsolder the three harnesses connected to the
power supply board.
1.
2.
3.
4.
Removing the power supply board
(See Fig.14 and 15)
Fig.13
Fig.14
Fig.15
Power
supply
board
CN251 Power
transformer
M
CN241
Solder
M
Solder
Solder
N
Power / fuse board
Power cord
Power
supply
board
Nut
Headphone jack
Headphone jack
Tie band
Solder
O
O
O
Solder
CN201
CN203
Hook
Power
transformer
board
FW201
CN291
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-8
Prior to performing the following procedure, remove
the top cover and the front panel assembly.
Pull out the volume knob on the front side of the front
panel and remove the nut attaching the system
control board.
Remove the two screws P attaching the power
switch board.
Disconnect the harness from connector CN714 on
the power switch board.
Remove the six screws Q attaching the system
control board on the back of the front panel.
On the back of the front panel, release the eight
joints by pushing the joint tabs inward.
Remove the operation switch panel toward the front.
Release the two hook attaching the system control
board.
1.
2.
3.
4.
5.
6.
Removing the system control board /
power switch board (See Fig.16 to 18)
Fig.16
Fig.17
Fig.18
Front panel assembly
Nut
Volume knob
System control board
Power switch
board
QQ
CN714
P
Joint
Joint
Joint Joint Joint Joint
Hook Hook
Operation switch panel
Joint
Joint
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-9
Adjustment method
<Adjustment method>
1.Set the volume control to minimum during this adjustment.(No signal & No load)
2.Set the surround mode OFF.
2.Turn VR301 and VR302 fully counterclockwise to warm up before adjustment.
If the heat sink is already warm from previous use the correct adjustment can not be made.
3.For L-ch,connect a DC voltmeter between TP301's B216 and B217 (Lch)
And,connect it between TP302's B218 and B219(Rch).
4.30 minutes later after power on, adjust VR301 for L-ch, or VR302 for R-ch so that the DC voltmeter
value has 1mV~10mV.
1.Tuner range
FM 87.5MHz~108.0MHz
AM(MW) 530kHz~1710kHz
Tuner section
Power amplifier section
TP302(Rch)
VR301 (Lch)
VR302 (Rch)
Heat sink
Adjustment of idling current
Measurement location TP301(Lch) , TP302(Rch)
Adjustment part VR301(Lch) , VR302(Rch)
Attention
This adjustment does not obtain a correct adjustment value immediately after the amplifier is
used (state that an internal temperature has risen).
Please adjust immediately after using the amplifier after turning off the power supply of the
amplifier and falling an internal temperature.
* It is not abnormal though the idling current might not become 0mA even if it is finished to turn variable
resistance (VR301,VR302) in the direction of counterclockwise.
TP301(Lch)
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-10
1
2
3
4
5
6
7
8
9
10
11
33
32
31
30
29
28
27
26
25
24
23
12 13 14 15 16 17 18 19 20 21 22
44 43 42 41 40 39 38 37 36 35 34
SDOS
I2C
SMUTE
BICK
LRCK
SDTI1
SDTI2
SDTI3
SDTO
DAUX
DFS
DZF2/OVF
RIN+
RIN-
LIN+
LIN-
ROUT1
LOUT1
ROUT2
LOUT2
ROUT3
LOUT3
NC DZFE TVDD DVDD DVSS PDN TST NC ADIF CAD1 CAD0
LOOP1 LOOP0/SDA/CDTI DIF1/SCL/CCLK DIF0/CSN P/S MCLK DZF1 AVSS AVDD VREFH VCOM
1.Pin layout
AK4527B (IC601) : A/D,D/A Converter
Description of major ICs
AK4527BVQ
Top View
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Pin name
SDOS
I2C
SMUTE
BICK
LRCK
SDTI1
SDTI2
SDTI3
SDTO
DAUX
DFS
NC
DZEF
TVDD
DVDD
DVSS
PDN
TST
SDTO Source Select Pin (Note 1)
"L" : Internal ADC output, "H" : DAUX input
Control Mode Select Pin
"L" : 3-wire Serial, "H" : I2C Bus
Soft Mute Pin (Note 1)
When this pin goes to "H", soft mute cycle is initialized.
When returning to "L", the output mute releases.
Audio Serial Data Clock Pin
Input Channel Clock Pin
DAC1 Audio Serial Data Input Pin
DAC2 Audio Serial Data Input Pin
DAC3 Audio Serial Data Input Pin
Audio Serial Data Output Pin
Sub Audio Serial Data Input Pin
Double Speed Sampling Mode Pin (Note 1)
"L" : Normal Speed, "H" : Double Speed
No Connect
No internal bonding.
Zero Input Detect Enable Pin
"L" : mode 7 (disable) at parallel mode,
zero detect mode is selectable by DZFM2-0 bits at serial mode.
"H" : mode 0 (DZF is AND of all six channels)
Output Buffer Power supply Pin, 2.7V~5.5V
Digital Power Supply Pin, 4.5V~5.5V
De-emphasis Pin, 0V
Power-Down & Reset Pin
When "L", the AK4527B is powered-down and the control registers are reset to default
state. If the state of P/S or CAD0-1 changes, then the AK4527B must be reset by PDN.
Test Pin
This pin should be connected to DVSS.
Function
AK4527(1/2)
I/O
I
I
I
I
I/O
I
I
I
O
I
I
-
I
-
-
-
I
I
2. Pin function (1/2)
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-11
No.
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Pin name
NC
ADIF
CAD1
CAD0
LOUT3
ROUT3
LOUT2
ROUT2
LOUT1
ROUT1
LIN-
LIN+
RIN-
RIN+
DZF2
OVF
VCOM
VREFH
AVDD
AVSS
DZF1
MCLK
P/S
DIF0
CSN
DIF1
SCL/CCLK
LOOP0
SAD/CDTI
LOOP1
No Connect
No internal bonding.
Analog Input Format Select Pin
"H" : Full-differential input, "L" : Single-ended input
Chip Address 1 Pin
Chip Address 0 Pin
DAC3 Lch Analog Output Pin
DAC3 Rch Analog Output Pin
DAC2 Lch Analog Output Pin
DAC2 Rch Analog Output Pin
DAC1 Lch Analog Output Pin
DAC1 Rch Analog Output Pin
Lch Analog Negative Input Pin
Lch Analog Positive Input Pin
Rch Analog Negative Input Pin
Rch Analog Positive Input Pin
Zero Input Detect 2 Pin (Note 2)
When the input data of the group 1 follow total 8192LRCK cycles with "0" input data,
this pin goes to "H".
Analog Input Overflow Detect Pin (Note 3)
This pin goes to "H" if the analog input of Lch or Rch is overflows.
Common Voltage Output Pin,AVDD/2
Large external capacitor around 2.2uF is used to reduce power-supply noise.
Positive Voltage Reference Input Pin,AVDD
Analog Power Supply Pin,4.5V~5.5V
Analog Ground Pin,0V
Zero Input Detect 1 Pin (Note 2)
When the input data of the group 1 follow total 8192 LRCK cycles with "0" input data,
this pin goes to "H".
Master Clock Input Pin
Parallel / Serial Select Pin
"L" : Serial control mode, "H" : Parallel control mode
Audio Data Interface Format 0 Pin in parallel mode
Chip select pin in 3-wire serial control mode
This pin should be connected to DVDD at I2C bus control mode
Audio Data Interface Format 1 Pin in parallel mode
Control Data Clock Pin in serial control mode
I2C = "L" : CCLK(3-wire Serial), I2C = "H" : SCL(I2CBus)
Loopback Mode 0 Pin in parallel control mode
Enables digital loop-back from ADC to 3 DACs.
Control Data Input Pin in serial control mode
I2C = "L" : CDTI(3-wire Serial), I2C = "H" : SDA(I2CBus)
Loopback Mode 1 Pin (Note 1)
Enable all 3 DAC channels to be input from SDTII.
Function
AK4527(1/2)
I/O
-
I
I
I
O
O
O
O
O
O
I
I
I
I
O
O
O
I
-
-
O
I
I
I
I
I
I
I
I/O
I
Pin function (2/2)
Notes : 1. SDOS, SMUTE, DFS, and LOOP1 pins are ORed with register data if P/S = "L".
2. The group 1 and 2 can be selected by DZFM2-0 bit if P/S = "L" and DZFME = "L".
3. This pin becomes OVF pin if OVFE bit is set to "1" at serial control mode.
4. All input pins should not be left floating.
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-12
2
3
4
1
5
L-S1
S-2
S-3
VSS
COM-1 6
7
8
9
S-4
S-5
S-6
COM-2
10
11
12
S-7
S-8
COM3
13
ST
14
GND
27
26
25
28
24
R-S1
S-2
S-3
VDD
COM-1
23
22
21
20
S-4
S-5
S-6
COM-2
19
18
17
S-7
S-8
COM3
16 DATA
15 CK
SHIFT RESISTOR
SHIFT
RESISTOR
&
LATCH
SHIFT
RESISTOR
&
LATCH
TC9164AN
TC9164AN (IC402): Analog switch
Switch to On/Off of S1 to S8 by control of LSI.
1.Function
2.Terminal Lay out & Block Diagram
CTL 1
L
H
L/H
CTL 2
L
L
H
Output
VIN 1
VIN 2
VIN 3
Control input - output signal
GND
8
Vout
7
V+
6
Vin3
5
1
Vin1
2
CTL1
3
Vin2
4
CTL2
6dB
AMP.
BIAS
NJM2246D(IC501):Video switch
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-13
AS7C31025-15 (IC641) : CMOS SRAM
Input buffer
512x256x8
Array
(1,048,576)
Column decoder Control
circuit
Row decoder
Sense amp
A0
A1
A2
A3
A4
A5
A6
A7
A8
I/O7
I/O0
A9 A10 A11 A12 A13 A14 A15 A16
Vcc
GND
Block diagram
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
A0
A1
A2
A3
CE
I/O0
I/O1
Vcc
GND
I/O2
I/O3
WE
A4
A5
A6
A7
A16
A15
A14
A13
OE
I/O7
I/O6
GND
Vcc
I/O5
I/O4
S12
A11
A10
A9
A8
32-pin TSOP II
AS7C1025 AS7C31025
Pin layout
WE
OE
CE
3
2
5
1
DC INPUT(Vin)
GND
DC OUTPUT(Vo)
CUSTOM IC
ON/OFF CONTROL(Vc)
PQ3DZ53 (IC681) : Regulator IC
2
5
3
1
CE
VDD
VOUT
GND
Vref
Current Limit
-
+
RN5RZ33BA (IC683) : Voltage Regurator
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
OUT4
OUT3
OUT2
OUT1
AVDD
SWIN
GNDS
SRin
SLin
GNDC
Cin
GNDR
Rin
GNDL
Lin
BYPASSR
BYPASSL
LTRE
LBASS3
LBASS2
LBASS1
DVDD
CLK
DATA
LATCH
DGND
AGND
SWout
SRout
SLout
Cout
Rout
Lout
AVSS
CL1
CL2
CR1
CR2
RTRE
RBASS3
RBASS2
RBASS1
OUT-
PUT
PORT volume
volume
volume
volume
volume
volume
MCU
I/F
tone tone
1.Block Diagram
M62446FP(IC428) : 6CH Master volume
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16,17
18
19~21
22
23,24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
SURROUND
BASS BOOST
INPUT-ATT
MUTING
AVDD
SWIN
A.GND
RR IN
RL IN
A.GND
C IN
A.GND
R IN
A.GND
L IN
BYPASSR,L
LTRE
LBASS3~1
CR2
RBASS2,4
RTRE
RBASS1
CR1
CL2
CL1
AVSS
L OUT
R OUT
C OUT
RL OUT
RR OUT
SW OUT
A.GND
D.GND
VOL STB
VOL DATA
VOL CLK
DVDD
O
O
O
O
-
I
-
I
I
-
I
-
I
-
I
-
-
-
O
-
-
-
I
O
I
-
O
O
O
O
O
O
-
-
I
I
I
-
SURROUND control terminal
BASS BOOST control terminal
Input attenuator control terminal
MUTING control terminal
Analog positive power supply terminal
SUB Woofer volume signal input terminal
Analog ground terminal
R ch volume signal input terminal for rear speaker
L ch volume signal input terminal for rear speaker
Analog ground terminal
Center volume signal input terminal
Analog ground terminal
R ch volume signal input terminal
Analog ground terminal
L ch volume signal input terminal
Non connect
Frequency adjustment terminal tone/treble
Frequency adjustment terminal tone/bass
Tone output terminal
Frequency adjustment terminal tone/bass
Frequency adjustment terminal tone/treble
Frequency adjustment terminal tone/bass
L/R volume input terminal
Tone output terminal
L/R volume input terminal
Analog negative power supply terminal
L ch output
R ch output
Center volume signal output terminal
L ch volume signal output terminal for rear speaker
R ch volume signal output terminal for rear speaker
SUB Woofer volume signal output terminal
Analog ground terminal
Digital ground terminal
Latch input terminal
Volume data input terminal
Clock input terminal for data transfer
Digital power supply terminal
Pin No. Symbol I/O Descriptions
2.Pin Function
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-16
Pin No. Symbol I/O Function
MN101C35DHK1 (IC701) : System controller
Pin function (1/2)
75
51
100 76
26 50
1
25
1
2
3
4
5
6
7
8
9,10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
TXD/SB00/P00
RXD/SBI0/P01
SBT0/P02
SB01/P03
SBI1/P04
SBT1/P05
BUZZER/P06
VDD
OSC1,2
VSS
XI
X0
MMOD
VREF-
AN0/PA0
AN1/PA1
AN2/PA2
AN3/PA3
AN4/PA4
AN5/PA5
AN5/PA5
AN5/PA5
VREF+
P07
RST /P27
RNOUT/TM0I0/P10
TM1I0/P11
TM2I0/P12
TM3I0/P13
TM4I0/P14
P15
IRQ0/P20
SENS/IRQ1/P21
IRQ2/P22
IRQ3/P23
IRQ4/P24
P25
SB02/P30
SBI2/P31
I
I
I/O
O
O
I
I
-
I/O
-
I
O
I
-
I
I
I
I
I
I
I
I
-
I
I
O
I
O
I
O
I/O
I
I
I
I
I
I
O
I
VOL.JOG IN_1
VOL.JOG IN_2
DATA (PLL)
CLK (PLL)
DE (PLL)
VIDEO S/C DVD
VIDEO S/C VCR
Power supply +5V
OSC (8MHz)
GND
GND
OPEN
GND
GND
KEY INPUT 1 (7KEY)
KEY INPUT 2 (7KEY)
KEY INPUT 3 (7KEY)
KEY INPUT 4 (7KEY)
KEY INPUT 5 (7KEY)
INH IN
CHIP SELECT 1
CHIP SELECT 2
Power supply +5V
VIDEO S/C DBS
RESET INPUT
RDS CLK OUT (RDS)
DCS INPUT
DCS OUTPUT
AVLINK VCR IN
AVLINK VCR OUT
RDS DATA (RDS)
PROTECTOR IN
REMOCON INPUT
TUNED IN (TUNER)
STEREO IN (TUNER)
RDS DAVN (RDS)
SELF CHECK INPUT
COMMAND (DSP)
STATUS (DSP)
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-17
Pin No. Symbol I/O Function
Pin function (2/2)
41
42
43
44
45
46
47
48
49 64
65 80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
SBT2/P32
P50
P51
P52
P53
P54
DGT17/P67
DGT16/P66
G16 G1
P87 P90
SEG24/PC2
SEG25/PC1
SEG26/PC0
SEG27/PB7
SEG28/PB6
SEG29/PB5
SEG30/PB4
SEG31/PB3
SEG32/PB2
SEG33/PB1
SEG34/PB0
SEG35/PD7
SEG36/PD6
SEG37/PD5
SEG38/PD4
SEG39/PD3
SEG40/PD2
SEG41/PD1
SEG42/PD0
VPP
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
CLK (DSP)
READY (DSP)
RESET (DSP)
RELAY S
RELAY C
RELAY L/R 1
RELAY L/R 2
RELAY HEADPHONE
FL GRID SIGNAL CONTROL OUT
FL SEGMENT SIGNAL CONTROL OUT
LED8 SIGNAL CONTROL OUT (FM/AM)
LED7 SIGNAL CONTROL OUT (TV/DBS)
LED6 SIGNAL CONTROL OUT (TAPE/CDR)
LED5 SIGNAL CONTROL OUT (VCR)
LED4 SIGNAL CONTROL OUT (CD)
LED3 SIGNAL CONTROL OUT (DVD)
LED2 SIGNAL CONTROL OUT (PHONO)
LED1 SIGNAL CONTROL OUT (DVD MULTI)
SOUSE MUTE
SUBWOOFER MUTE
TUNER MUTE
POWER ON (STANDBY)
SURROUND
DATA (A.SW)
CLK (A.SW)
STB (A.SW)
LATCH (A.SW)
DATA (VOL)
CLK (VOL)
VPP
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-18
DLCKS terminal
L
L
H
H
DLONterminal
L
H
L
H
DLL clock setting
SCKI input (DLL circuit OFF)
Four times XI clock
Three times XI clock
Six times XI clock
1
2
3
4
5
6
7
8~11
12
13
14
15
16~18
19
20
21
22
23
24
25
26
27,28
29~31
32,33
34
35
36
37
38,39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54~61
62
63~70
71
72~80
81
82~89
90
91
92,93
94
95
96
97
98,99
100
Pin No. Symbol I/O Function
RST
MIMD
MICS
MILP
MIDIO
MICK
MIACK
FI0~3
IRQ
VSS
LRCKA
BCKA
SDO0~2
SD03
LRCKB
BCKB
SDT0
SDT1
VDD
LRCKOA
BCKOA
TEST0,1
LRCKOB,BCKOB,TXO
TEST2,3
RX
VSS
TSTSUB0
FCONT
TSTSUB1,TSTSUB2
PDO
VDDA
PLON
AMPI
AMPO
CKI
VSSA
CKO
LOCK
VSS
WR
OE
CE
VDD
IO7~0
VSS
AD0~7
VDD
AD8~16
VSS
PO0~7
VDDDL
LPFO
DLON,DLCKS
SCKO
VSSDL
SCKI
VSSX
XO,XI
VDDX
I
I
I
I
I/O
I
O
I
I
-
I
I
O
-
I
I
I
I
-
O
O
I
-
I
I
-
I
O
I
O
-
I
I
O
I
-
O
O
-
O
O
O
-
I/O
-
O
-
O
-
O
-
O
I
-
-
I
-
I/O
-
Reset signal input terminal (L:reset H:Operation usually)
Microcomputer interface mode selection input terminal (L:serial H:IC bus)
Microcomputer interface chip select input terminal
Microcomputer interface latch pulse input
Microcomputer interface data I/O terminal
Microcomputer interface clock input terminal
Microcomputer interface acknowledge output terminal
Flag input terminal 0~3
Interrupt input terminal
Digital ground terminal
Audio interface LR clock input terminal A
Audio interface bit clock input terminal A
Audio interface data output terminal 0
Non connect
Audio interface LR clock input terminal B
Audio interface bit clock input terminal B
Audio interface data input terminal 0
Audio interface data input terminal 1
Power supply for digital circuit
Audio interface LR clock output terminal A
Audio interface bit clock output terminal A
Test input terminal 0/1 (L:test H:operation usually)
Non connect
Test input terminal (L:test H:operation usually)
SPDIF input terminal
Ground terminal for digital circuit
Test sub input terminal 0 (L:test H:operation usually)
VCO Frequency control output terminal
Test sub input terminal 1,2 (L:test H:operation usually)
Phase error signal output terminal
Power supply for analog circuit
Clock selection input terminal (L:external clock H:VCO clock)
AMP.input terminal for LPF
AMP.output terminal for LPF
External clock input terminal
Ground terminal for analog circuit
DIR Clock output terminal
VCO Lock detection output terminal
Ground terminal for digital circuit
External SRAM writing signal output terminal
External SRAM output enable signal output terminal
External SRAM chip enable signal output terminal
Power supply terminal for digital circuit
External SRAM data I/O terminal 7~0
Ground terminal for digital circuit
External SRAM address output terminal 0~7
Power supply terminal for digital circuit
External SRAM address output terminal 8~16
Ground terminal for digital circuit
General purpose output terminal 0~7
Power supply terminal for DLL
LPF output terminal for DLL
Refer to the undermentioned table
Non connect
Ground terminal for DLL
External system clock input terminal
Ground termonal for oscillation circuit
Oscillation I/O terminal
Power supply terminal for oscillation circuit
TC9446F-014(IC631):Digital signal processor for dolby digital (AC-3)
/ MPEG2 audio decode
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

RX-6010VBK/6018VBK
1-19
1~8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25~32
33
34,35
36
37,38
39
40
41
42
43
44
45,46
47
48
49
50
51,52
53
54~63
64,65
66
67
68
69,70
71
72
73~80
81
82
83
84
85
86
87
88
89
90~93
94
95~100
VDD
X2
X1
VSS
XT2
XT1
RESET
AUTODATA
LOCK
DIGITAL0
FORMAT
CHANNEL
ERR
RSTDET
AVDD
AVREF0
AVSS
AV REF1
RX,TX
DSPCOM
DSPSTS
DSPCLK
DSPRDY
MIDIO_IN/OUT
MICK
MICS
MILP
MIACK
DSPRST
CDTI/CDTO
CCLK
CS
XTS
PD
GND
VDD
3D-ON
3D-ON
ANA/T-TONE
REF-MIX
D.MUTE
S.MUTE
ASW1~4
TEST
Non connect
Power supply terminal
Connecting the crystal oscillator for system main clock
Connecting the crystal oscillator for system main clock
Connect to GND
Connecting the crystal oscillator for system sub clock
Connecting the crystal oscillator for system sub clock
System reset signal input
Output of DSP to general-purpose port
Output of DSP to general-purpose port
Output of DSP to general-purpose port
Output of DSP to general-purpose port
Output of DSP to general-purpose port
Output of DSP to general-purpose port
Reset signal input
Power supply terminal
Connect to GND
Connect to GND
Connect to GND
Non connect
Power supply terminal
Not use
Non connect
Communication port from IC701
Status communication port to IC701
Clock input from IC701
Ready signal input from IC701
Non connect
Interface I/O terminal with microcomputer
Interface I/O terminal with microcomputer of clock signal
Interface I/O terminal with microcomputer of chip select
Interface I/O termonal with microcomputer
Interface I/O termonal with microcomputer
Non connect
Reset signal output of DSP
Non connect
Interface I/O terminal with microcomputer
Interface I/O terminal with microcomputer of clock signal
Interface I/O terminal with microcomputer of chip select
OSC Select
Non connect
Reset signal output
Connect to GND
Non connect
Power supply
Non connect
Switch at output destination of surround channel
Test tone control
Control at output destination of LFE channel
Non connect
Mute of the digital out terminal is controlled
Mute of the audio signal is controlled
Non connect
Selection of digital input selector
Test terminal
Non connect
-
-
O
I
-
O
I
I
I
I
I
I
I
I
I
-
-
-
-
-
-
-
-
I
O
I
I
-
I/O
O
O
O
O
-
O
-
I/O
O
O
O
-
O
-
-
-
-
O
O
O
-
O
O
-
O
-
-
Pin No. Symbol I/O Function
75 ~ 51
1 ~ 25
76
100
~
50
26
~
1.Pin layout
2.Pin function
UPD784215AGC103(IC671):UNIT CPU
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland

Printed in Japan
200102(V)
VICTOR COMPANY OF JAPAN, LIMITED
AUDIO & COMMUNICATION BUSINESS DIVISION
PERSONAL & MOBILE NETWORK BUSINESS UNIT. 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan
(No.20909)
RX-6010VBK/6018VBK
www.freeservicemanuals.info
07/11/2016
Published in Heiloo Holland