JVC LT-32C650 User manual

• DonotconnecttheTVtothemainssupplyuntilyouhavecompletedalltheconnections.
• AlwaysdisconnecttheTVfromthemainssocketwhennotinuseforalongperiodoftime.
• The buttonontheremotecontrolisonlyusedforswitchingtheTVintostandby,itdoesnotdisconnecttheTVfromthemainspower.
Tocompletelydisconnectthemainspower,pleaseremovethemainsplugfromthemainssocket.
TheLCDdisplayisveryfragile,andmustbeprotectedatalltimeswheninstallingandremovingthebasestand.Besurethatnohardorsharpobject,
oranythingthatcouldscratchordamagetheLCDdisplay,comesintocontactwithit.DONOTexertpressureonthefrontoftheTVatanytimebecause
thescreencouldcrack.
PleaseinspectyourTVfordamageafterunpacking.Ifyoudonoticeanydamagepleaseconsultyourdealer.
Removeallpackagingfromtheunit.Retainthepackaging.Ifyoudisposeofitpleasedosoaccordingtoanylocalregulations.
 TV
 TVStand
 RemoteControl/
AAABatteriesx2
 Screwsx4
 FAVCable
 InstructionManual
 QuickStartGuide
Unpacking
1
1. ConnectoneendoftheRFcoaxialcabletotheaerialsocketonthewall
andtheotherendofthecabletotheANTsocketonthebackofyourTV.
2. PlugtheTVintoamainssocketandswitchonatthemains.
3. Instandbymode,pressthe buttonontheremotecontroltoturnthe
TVon.TheLEDindicatorwillashforafewsecondsthentheTVwill
switchon.
Connecting the Aerial and Turning on the TV
4
Fitting the Stand to the TV
1. EnsuretheTVisswitchedoandnotconnectedtothemainspowersupply.
2. LaytheTVdownonaatsurfaceideallyontheedgeofatablesothebaseoftheTVslightlyoverhangstheedgeofthetable,withtheback
sidefacingup.Pleasemakesureasoftcushionedmaterial(suchasadrybathtowelorthickpieceoffoam)isplacedbeneaththescreen.
3. Slidethestandunderthelip,theneckwilltsnuglyoverthescrewholes.ThenscrewthestandtotheTVusingthe4screwssupplied.
Installing the Base Stand
3
1. Slideopenthebatterycompartmentonthebackoftheremotecontrol.
Operating Your Remote Control
2
Thank youforpurchasingyournewJVCTV.
YournewTVincorporatesthelatesttechnologytoenhanceyourviewing
experience.Wewouldsuggestthatyouallowabout20minsforinitialsetup.
Pleasefollowthisguideforasuccessfulrsttimeinstallation.
Thelatesteco-friendlypower-savingtechnologywillswitchotheTVif
itisleftonandidlefor4hours.Pleasereferto“AutoStandby”underthe
“TimeSettings”sectionoftheinstructionmanualformoredetail.
Quick Start Guide
32" LED Smart HD TV
LT-32C650(A)
Slide under
the lip
Slide under
the lip
SCART
SPDIF
Optic.OUT
VGA
ANT.
HDMI1(ARC)
HDMI2 HDMI3
LAN
Table
Cushioned
material
2. InserttwoAAAsizebatteries.Makesuretomatchthe(+)and(-)
endsofthebatterieswiththe(+)and(-)endsindicatedinthebattery
compartment.
3. Slidethebatterycompartmentcoverbackintoplace.Makesureitclicks
intoplace.
Optional
Ifyouwanttoconnecttotheinternetviaawiredconnection
thenconnectyourethernetcabletotheLANsocket.
SCART
SPDIF
Coax.OUT
VGA
ANT.
HDMI1(ARC)
HDMI2
LAN
SCART
SPDIF
Coax.OUT
VGA
ANT.
HDMI 1(ARC)
HDMI 2
LAN
RF coaxial cable
(not included)

• DonotconnecttheTVtothemainssupplyuntilyouhavecompletedalltheconnections.
• AlwaysdisconnecttheTVfromthemainssocketwhennotinuseforalongperiodoftime.
• The buttonontheremotecontrolisonlyusedforswitchingtheTVintostandby,itdoesnotdisconnecttheTVfromthemainspower.
Tocompletelydisconnectthemainspower,pleaseremovethemainsplugfromthemainssocket.
TheLCDdisplayisveryfragile,andmustbeprotectedatalltimeswheninstallingandremovingthebasestand.Besurethatnohardorsharpobject,
oranythingthatcouldscratchordamagetheLCDdisplay,comesintocontactwithit.DONOTexertpressureonthefrontoftheTVatanytimebecause
thescreencouldcrack.
PleaseinspectyourTVfordamageafterunpacking.Ifyoudonoticeanydamagepleaseconsultyourdealer.
Removeallpackagingfromtheunit.Retainthepackaging.Ifyoudisposeofitpleasedosoaccordingtoanylocalregulations.
 TV
 TVStand
 RemoteControl/
AAABatteriesx2
 Screwsx4
 FAVCable
 InstructionManual
 QuickStartGuide
Unpacking
1
1. ConnectoneendoftheRFcoaxialcabletotheaerialsocketonthewall
andtheotherendofthecabletotheANTsocketonthebackofyourTV.
2. PlugtheTVintoamainssocketandswitchonatthemains.
3. Instandbymode,pressthe buttonontheremotecontroltoturnthe
TVon.TheLEDindicatorwillashforafewsecondsthentheTVwill
switchon.
Connecting the Aerial and Turning on the TV
4
Fitting the Stand to the TV
1. EnsuretheTVisswitchedoandnotconnectedtothemainspowersupply.
2. LaytheTVdownonaatsurfaceideallyontheedgeofatablesothebaseoftheTVslightlyoverhangstheedgeofthetable,withtheback
sidefacingup.Pleasemakesureasoftcushionedmaterial(suchasadrybathtowelorthickpieceoffoam)isplacedbeneaththescreen.
3. Slidethestandunderthelip,theneckwilltsnuglyoverthescrewholes.ThenscrewthestandtotheTVusingthe4screwssupplied.
Installing the Base Stand
3
1. Slideopenthebatterycompartmentonthebackoftheremotecontrol.
Operating Your Remote Control
2
Thank youforpurchasingyournewJVCTV.
YournewTVincorporatesthelatesttechnologytoenhanceyourviewing
experience.Wewouldsuggestthatyouallowabout20minsforinitialsetup.
Pleasefollowthisguideforasuccessfulrsttimeinstallation.
Thelatesteco-friendlypower-savingtechnologywillswitchotheTVif
itisleftonandidlefor4hours.Pleasereferto“AutoStandby”underthe
“TimeSettings”sectionoftheinstructionmanualformoredetail.
Quick Start Guide
32" LED Smart HD TV
LT-32C650(A)
Slide under
the lip
Slide under
the lip
SCART
SPDIF
Optic.OUT
VGA
ANT.
HDMI1(ARC)
HDMI2 HDMI3
LAN
Table
Cushioned
material
2. InserttwoAAAsizebatteries.Makesuretomatchthe(+)and(-)
endsofthebatterieswiththe(+)and(-)endsindicatedinthebattery
compartment.
3. Slidethebatterycompartmentcoverbackintoplace.Makesureitclicks
intoplace.
Optional
Ifyouwanttoconnecttotheinternetviaawiredconnection
thenconnectyourethernetcabletotheLANsocket.
SCART
SPDIF
Coax.OUT
VGA
ANT.
HDMI1(ARC)
HDMI2
LAN
SCART
SPDIF
Coax.OUT
VGA
ANT.
HDMI 1(ARC)
HDMI 2
LAN
RF coaxial cable
(not included)

• DonotconnecttheTVtothemainssupplyuntilyouhavecompletedalltheconnections.
• AlwaysdisconnecttheTVfromthemainssocketwhennotinuseforalongperiodoftime.
• The buttonontheremotecontrolisonlyusedforswitchingtheTVintostandby,itdoesnotdisconnecttheTVfromthemainspower.
Tocompletelydisconnectthemainspower,pleaseremovethemainsplugfromthemainssocket.
TheLCDdisplayisveryfragile,andmustbeprotectedatalltimeswheninstallingandremovingthebasestand.Besurethatnohardorsharpobject,
oranythingthatcouldscratchordamagetheLCDdisplay,comesintocontactwithit.DONOTexertpressureonthefrontoftheTVatanytimebecause
thescreencouldcrack.
PleaseinspectyourTVfordamageafterunpacking.Ifyoudonoticeanydamagepleaseconsultyourdealer.
Removeallpackagingfromtheunit.Retainthepackaging.Ifyoudisposeofitpleasedosoaccordingtoanylocalregulations.
 TV
 TVStand
 RemoteControl/
AAABatteriesx2
 Screwsx4
 FAVCable
 InstructionManual
 QuickStartGuide
Unpacking
1
1. ConnectoneendoftheRFcoaxialcabletotheaerialsocketonthewall
andtheotherendofthecabletotheANTsocketonthebackofyourTV.
2. PlugtheTVintoamainssocketandswitchonatthemains.
3. Instandbymode,pressthe buttonontheremotecontroltoturnthe
TVon.TheLEDindicatorwillashforafewsecondsthentheTVwill
switchon.
Connecting the Aerial and Turning on the TV
4
Fitting the Stand to the TV
1. EnsuretheTVisswitchedoandnotconnectedtothemainspowersupply.
2. LaytheTVdownonaatsurfaceideallyontheedgeofatablesothebaseoftheTVslightlyoverhangstheedgeofthetable,withtheback
sidefacingup.Pleasemakesureasoftcushionedmaterial(suchasadrybathtowelorthickpieceoffoam)isplacedbeneaththescreen.
3. Slidethestandunderthelip,theneckwilltsnuglyoverthescrewholes.ThenscrewthestandtotheTVusingthe4screwssupplied.
Installing the Base Stand
3
1. Slideopenthebatterycompartmentonthebackoftheremotecontrol.
Operating Your Remote Control
2
Thank youforpurchasingyournewJVCTV.
YournewTVincorporatesthelatesttechnologytoenhanceyourviewing
experience.Wewouldsuggestthatyouallowabout20minsforinitialsetup.
Pleasefollowthisguideforasuccessfulrsttimeinstallation.
Thelatesteco-friendlypower-savingtechnologywillswitchotheTVif
itisleftonandidlefor4hours.Pleasereferto“AutoStandby”underthe
“TimeSettings”sectionoftheinstructionmanualformoredetail.
Quick Start Guide
32" LED Smart HD TV
LT-32C650(A)
Slide under
the lip
Slide under
the lip
SCART
SPDIF
Optic.OUT
VGA
ANT.
HDMI1(ARC)
HDMI2 HDMI3
LAN
Table
Cushioned
material
2. InserttwoAAAsizebatteries.Makesuretomatchthe(+)and(-)
endsofthebatterieswiththe(+)and(-)endsindicatedinthebattery
compartment.
3. Slidethebatterycompartmentcoverbackintoplace.Makesureitclicks
intoplace.
Optional
Ifyouwanttoconnecttotheinternetviaawiredconnection
thenconnectyourethernetcabletotheLANsocket.
SCART
SPDIF
Coax.OUT
VGA
ANT.
HDMI1(ARC)
HDMI2
LAN
SCART
SPDIF
Coax.OUT
VGA
ANT.
HDMI 1(ARC)
HDMI 2
LAN
RF coaxial cable
(not included)

Well done,yournewTVisnowreadytouse.Youwillndthattherearemanyexcitingfeaturesavailable.Togettoknowallthesefeatures,pleasetake
sometimetoreadtheinstructionmanualprovidedwithyourTV.
(QSG-LT-32C650(A)-150827V1)
Need More Help!
IfyouneedmorehelpsettingupyourTVthenpleasecall:
UK: 0344 561 1234
Ireland: 1890 818 575
Linesareopen24/7
1. ThersttimeyouturntheTVon,itwillgostraightintotheFirst Time Installationmenu.
Pleaseensuretheaerialispluggedin.Pressthe buttonstohighlightyourlanguagethen
pressOK.
Getting Started
Connecting to the Internet
5
6
Allofthesettingon'Firsttimeinstallations'menuarepresetforthemajorityofcustomersin
theUK,ifyouwishyoucanchangethesettingbyselectingeachsettingandpressingthe
buttons.
If youView TV Through a Set Top Box
IfyouhaveattachedaSettopboxsuchasSky/VirginorBTviaaHDMIcableselectDigitalAerial
toNO.ThiswillmeanyourTVwillnottrytotuneanychannelsin.Toviewyoursettopboxpress
theSOURCEbuttonandselecttheHDMIsocketyouhaveattachedyoursettopboxto.
2. ConrmthesesettingsbypressingOK.
3. Pressthe  buttonstohighlightHomeModethenpressOK.
ToaccessallthefeaturesofyourSmartTVyoumustbeconnectedtotheinternet.Ifyoudonot
wishtosetupyournetworkconnectionyoucanskipthissectionbypressing ,howeverwe
recommendyousetupyournetworkconnectionnow.
WIRED Connection
• IfyouhaveconnectedyourethernetcabletotheLANsocketonthebackofyourTVpress
the  buttonstoselectWIREDDEVICE.WhenNetworksaysENABLEDpresstheOKbutton.
WIRELESS Connection
Youcanconnectusingawirelessconnectionviayourrouter.
1. Pressthe  buttonstoselectWIRELESSDEVICE.Waitafewsecondsandalistofallwireless
networkswillbedisplayed.
2. Pressthe  buttonstoselectyourwirelessnetworkthenpressOK.
3. Younowneedtoenteryourpassword,akeyboardwillappear.Pressthe    buttons
toselectaletter/number/symbolandpressOKtoentereachone.Onceyouhavetypedyour
passwordhighlightOKandpressOK.ThenetworkwillnowshowConnected.
4. PresstheOKbuttontocontinue.
Tuning in Your TV
7
Choose Region (UK only)
Duringtuning,yourTVmayhavereceivedsignalsfrommorethanonetransmitter.IfthishasoccurredtheChooseRegionscreenwillbedisplayed.Thiswill
enableyoutoselectthecorrectregionaltransmissionforthelocalnewsservicethatyourequire.
1. Pressthe buttontohighlightPrimary region,thenpressthe  buttonsto
selectyourPrimaryRegione.g.England.
2. Pressthe buttontohighlightSecondary region,thenpressthe  buttons
toselectyourSecondaryRegione.g.London.
3. Pressthe buttontohighlightTertiary region,thenpressthe  buttonsto
selectyourTertiaryRegione.g.GreaterLondon.
4. Pressthe buttontohighlightSavethenpressOK.
YourTVwillnowstartautomaticchannelscan.ItwilltuneinallavailableTVchannels.
5. TheScanstatisticsscreenwillappear,showingyoutheamountofTVandradio
stationsthathavebeentunedin.PressOKtoexitthisscreen.
6. TheEditChannellistwillappear,presstheEXITbuttontoremovethis.YourTVis
nowfullytunedinandreadytouse.

Well done,yournewTVisnowreadytouse.Youwillndthattherearemanyexcitingfeaturesavailable.Togettoknowallthesefeatures,pleasetake
sometimetoreadtheinstructionmanualprovidedwithyourTV.
(QSG-LT-32C650(A)-150827V1)
Need More Help!
IfyouneedmorehelpsettingupyourTVthenpleasecall:
UK: 0344 561 1234
Ireland: 1890 818 575
Linesareopen24/7
1. ThersttimeyouturntheTVon,itwillgostraightintotheFirst Time Installationmenu.
Pleaseensuretheaerialispluggedin.Pressthe buttonstohighlightyourlanguagethen
pressOK.
Getting Started
Connecting to the Internet
5
6
Allofthesettingon'Firsttimeinstallations'menuarepresetforthemajorityofcustomersin
theUK,ifyouwishyoucanchangethesettingbyselectingeachsettingandpressingthe
buttons.
If youView TV Through a Set Top Box
IfyouhaveattachedaSettopboxsuchasSky/VirginorBTviaaHDMIcableselectDigitalAerial
toNO.ThiswillmeanyourTVwillnottrytotuneanychannelsin.Toviewyoursettopboxpress
theSOURCEbuttonandselecttheHDMIsocketyouhaveattachedyoursettopboxto.
2. ConrmthesesettingsbypressingOK.
3. Pressthe  buttonstohighlightHomeModethenpressOK.
ToaccessallthefeaturesofyourSmartTVyoumustbeconnectedtotheinternet.Ifyoudonot
wishtosetupyournetworkconnectionyoucanskipthissectionbypressing ,howeverwe
recommendyousetupyournetworkconnectionnow.
WIRED Connection
• IfyouhaveconnectedyourethernetcabletotheLANsocketonthebackofyourTVpress
the  buttonstoselectWIREDDEVICE.WhenNetworksaysENABLEDpresstheOKbutton.
WIRELESS Connection
Youcanconnectusingawirelessconnectionviayourrouter.
1. Pressthe  buttonstoselectWIRELESSDEVICE.Waitafewsecondsandalistofallwireless
networkswillbedisplayed.
2. Pressthe  buttonstoselectyourwirelessnetworkthenpressOK.
3. Younowneedtoenteryourpassword,akeyboardwillappear.Pressthe    buttons
toselectaletter/number/symbolandpressOKtoentereachone.Onceyouhavetypedyour
passwordhighlightOKandpressOK.ThenetworkwillnowshowConnected.
4. PresstheOKbuttontocontinue.
Tuning in Your TV
7
Choose Region (UK only)
Duringtuning,yourTVmayhavereceivedsignalsfrommorethanonetransmitter.IfthishasoccurredtheChooseRegionscreenwillbedisplayed.Thiswill
enableyoutoselectthecorrectregionaltransmissionforthelocalnewsservicethatyourequire.
1. Pressthe buttontohighlightPrimary region,thenpressthe  buttonsto
selectyourPrimaryRegione.g.England.
2. Pressthe buttontohighlightSecondary region,thenpressthe  buttons
toselectyourSecondaryRegione.g.London.
3. Pressthe buttontohighlightTertiary region,thenpressthe  buttonsto
selectyourTertiaryRegione.g.GreaterLondon.
4. Pressthe buttontohighlightSavethenpressOK.
YourTVwillnowstartautomaticchannelscan.ItwilltuneinallavailableTVchannels.
5. TheScanstatisticsscreenwillappear,showingyoutheamountofTVandradio
stationsthathavebeentunedin.PressOKtoexitthisscreen.
6. TheEditChannellistwillappear,presstheEXITbuttontoremovethis.YourTVis
nowfullytunedinandreadytouse.