JVC KV-C1008 User manual

1
KV-C1008
TV Tuner Unit : Instructions
LVT1185-001A
[A]
0904MNMMDWJEIN
EN
WARNINGS
• USE WITH DC 12 V NEGATIVE GROUND VEHICLES.
If your vehicle does not have this system, a voltage inverter is required, which can be purchased
at JVC car audio dealers.
•
DO NOT INSTALL THE MONITOR IN A LOCATION WHICH OBSTRUCTS DRIVING AND VISIBILITY,
OR WHERE APPLICABLE LAWS AND REGULATIONS PROHIBIT THE INSTALLATION.
• NEVER USE BOLTS OR NUTS FROM THE VEHICLE’S SAFETY DEVICES FOR INSTALLATION.
If bolts or nuts from the steering wheel, brakes or other safety devices are used for installation, it
may cause an accident.
• INSTALL THE ANTENNA IN A PROPER LOCATION.
Be sure to select a location for installation of the antenna so that the antenna is not protruding
beyond the width or the front or back of the vehicle. If it is protruding, it might come into contact with
a pedestrian or other object and cause an accident.
• ATTACH THE WIRES CORRECTLY.
If the wiring is not correctly performed, it may cause a fire or an accident. In particular, be sure to run
and secure the lead wire so that it does not get tangled with a screw or the moving portion of a seat rail.
To prevent short circuits, it is recommended that you disconnect the battery’s negative
terminal and make all electrical connections before installing the unit. If you are not sure how to
install this unit correctly, have it installed by a qualified technician.
• Avoid installing the unit in the following places.
– Where it would hinder your safety driving.
– Where it would be exposed to direct sunlight or heat directly from the heater or placed in an
extremely hot place.
– Where it would be subject to rain, water splashes or excessive humidity.
– Where it would be subject to dust.
– Where it would be positioned on an unstable place.
– Where it could damage the car’s fittings.
– Where proper ventilation would not be maintained, such as under a floor mat.
– Where it would be located near inflammable objects (since heat is generated inside the unit).
INSTALLATION
•The following illustrations show typical installation.
If you have any questions or require information regarding installation kits, consult your JVC car
audio dealer or a company supplying kits.
• Handle the Lithium coin battery (product number: CR2025) with care.
– Store the battery in a place where children cannot reach.
If a child accidentally swallows the battery, consult a doctor immediately.
– Do not recharge, short, disassemble, or heat the battery or dispose of it in a fire.
These behaviors may cause the battery to be overheated, crack or fire.
– Do not leave the battery with other metallic materials.
Doing this may cause the battery to be overheated or cracked. It may cause a fire.
– When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the battery
may be overheated, crack or fire.
– Do not poke the battery with tweezers or similar tools.
Doing this may cause the battery to be overheated or cracked. It may cause a fire.
Parts list
The following parts are provided with this unit. After checking them, please set them correctly.
Battery Remote controller
CR2025
RM-RK510
Power cordAV bus cableBrackets
Fixing screws
—M4 x 8 mm
Remote sensor unit with
double-faced adhesive tape
When used with KD-AV7008:
TV tuner unit (in trunk)
Diversity antenna
KD-AV7008
(separately purchased)
Diversity antenna Monitor system (separately purchased)
TV tuner unit (under the passenger’s seat)
Remote sensor unit
When used with another monitor system:
Diversity antennas with
a cleaner
Installing the unit
While mounting the unit, be sure to use the tapping screws (not supplied) of appropriate length
so that they will not damage any parts of the car.
Bracket
Tapping screws (not supplied)
Floor
Fixing screws
—M4 x 8 mm
Installing the antenna
Before installing:
•The diversity antenna supplied with this unit is designed specifically for use with JVC TV tuner
unit. (It cannot be connected to the car radio.)
•Do not rub the antenna or the antenna’s cable with alcohol, benzine, thinner, gasoline or other
volatile substances.
•Attach to the inside of the car window glass.
•
Be sure to wipe the window surface where the antenna will be attached with the cleaner (supplied)
to remove moisture, dirt, dust, wax, oil or other substances. (If there is moisture, oil or other wet
substances on the attachment surface, the attachment tape will not stick well and easily come off.)
•Identify the exact attachment location and confirm that the adhesive surfaces (antenna base
and attachment parts) will not be placed on a heating wire, glass antenna or wiper motor.
CAUTION
Since there may be legal regulations defining the permissible installation locations for the
monitor system which differ by country or by state, be sure to install the monitor in a location
complying with any such laws.
Attachment parts
Antenna base
Peel off the cover
paper.
Peel off the cover paper.
Attachment location
Example of installation, side window
• When the attachment surface
overlaps with an electrode
Attach the antenna to either the left or right of
the electrode.
• When the attachment surface
interferes with a rear wiper motor
or a high-mounted brake light
Move the antenna’s attachment position
upwards to avoid interference.
Heating wires
Electrode
• Installing the antenna cord
Install the cord from the antenna to the TV
tuner unit through the interior trim and under
the carpet, and secure it using the cord
clampers and mirror mats. Mirror mats (separately purchased)
Cord clampers (separately purchased)
2 Peel off the cover paper from the attachment
parts in turn and attach to the surface.
1 Peel off the cover paper from the antenna
base and attach to the surface.
TROUBLESHOOTING
• TV tuner does not work at all.
* Is the remote sensor unit connected correctly?
• No sound is heard.
* Have you adjusted the volume level on the monitor?
• Picture does not come on the screen.
* Is the correct input selected on the monitor?
• The fuse blows.
* Are the red, yellow, and black leads connected correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• TV stations cannot be received.
* Is the area setting (see page 2) correct?
© 2004 Victor Company of Japan, Limited
When used with any other monitor system than KD-AV7008.

2
REMOTE
SENSOR RESET 3214
AV OUTPUT
RLVIDEO
POWER AV BUS AUDIO
TV ANTENNA
TV TUNER UNIT KV-C1008
MULTIMEDIA DVD/CD RECEIVER WITH REMOVABLE MONITOR HIDEAWAY UNIT KD-AV7008
AV INPUT 1
L
RAUDIO
FM / AM ANTENNA
POWER
BACKCAMERA
REMOTE
CENTER
SPEAKER
CENTER
SUB
WOOFER
L
R
REAR
L
R
FRONT
VIDEO
AV INPUT 2
L
RAUDIO VIDEO TO CHANGER AV BUS TO MAIN UNIT
PRE OUT
AUDIO
VIDEO L R
AV OUTPUT
When used with KD-AV7008: When used with another monitor system:
ELECTRICAL CONNECTIONS
REMOTE
SENSOR RESET 3214
AV OUTPUT
RLVIDEO
POWER AV BUS AUDIO
TV ANTENNA
TV TUNER UNIT KV-C1008
Remote sensor unit
See “Typical
Connections”
below.
Antenna base
Antenna element
Hideaway unit (supplied for KD-AV7008)
AV bus cable
(supplied) *2
Monitor system
(separately purchased)
Cord protector *1
*3
*3
*1 Use this to protect the cord (not to be pinched with the door, etc.)
*2 For controlling KV-C1008 through KD-AV7008, this connection is only required. For other connections, refer to the manual
supplied for KD-AV7008.
*3Reset the unit after installation is finished by pressing in with a ball-point pen or a similar tool.
Typical Connections
Before connecting:
• Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to the unit.
POWER AV BUS
AV OUTPUT
VIDEO
LAUDIOR
4
1
2
3
3A
*1 Before checking the
operation of this unit prior
to installation, this lead
must be connected,
otherwise power cannot be
turned on.
2
Ignition switch
Black
Yellow *1
Red
Blue with white stripe
1
To metallic body or chassis of the car
To a live terminal in the
fuse block connecting to
the car battery (bypassing
the ignition switch)
Fuse block
*2 Not included with this unit.
To an accessory terminal in the fuse block
To the remote control lead of JVC FM modulator KS-IF200
(for details, refer to the Instructions of KS-IF200.)
*2
The following is not required when connecting this TV tuner unit to KD-AV7008.
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle
does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealer.
RM-RK510
Sensing area
Double-faced adhesive
tape (supplied)
Connect the colored leads of the power cord in
the order specified in the illustration below.
Finally connect the wiring
harness to the unit.
•Replace the fuse with one of the specified ratings. If the fuse blows frequently,
consult your JVC car audio dealer.
• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.
OPERATIONS
The following operations cannot be used when connecting this TV tuner
unit to KD-AV7008.
•When connecting to KD-AV7008, refer to the Instructions supplied with them.
•Before watching the TV, perform the area setup (see below).
1Standby/On button
Press to turns on and off the TV tuner unit.
2TV CH (channel) 5/ ∞button
• Press to search for the TV channels (“SEARCH”appears). When a TV station is received, search will stop.
•Press and hold to activate manual search (“MANUAL”appears) for the TV station. Then press
repeatedly to change the TV channels.
3AUTO PRESET button
•Press to display the preset channel list.
•
Press and hold to preset the receivable TV stations automatically into the preset number buttons (1 –12).
4DISP (display) button
•Press to display the preset channel number on the monitor.
•
Press and hold to call up the area setup screen. Then press number button (1, 2, 3, or 4) to select
your area. (Normally press 1. For New Zealand, press 2;for Indonesia, press 3;for CCIR, press 4.)
5Preset number buttons (1 –12)
•Press to select the preset channel number directly.
•Press and hold to store a TV station into preset number (1 –12).
SPECIFICATIONS
TV TUNER UNIT
TV antenna jack ×4
AV bus terminal ×1
Remote sensor jack ×1
Output Video: RCA pin ×1; 1 V(p-p), 75 Ω
Audio: RCA pin ×2; 150 mV(rms)
Dimensions (W ×H ×D): 163 mm ×28 mm ×122 mm
Mass: 0.6 kg
CAUTION
DO NOT leave the remote controller in a place (such as dashboards) exposed to
direct sunlight for a long time. Otherwise, it may be damaged.
1
2
3
4
5
12
3
CR2025
DIVERSITY ANTENNANA
Output impedance: 75 Ω×4 (with mini plug)
Cord length: 5 m
Dimensions (approx.) (W ×H ×D):
440 mm ×490 mm ×18 mm (without the cable)
Mass (each unit) (approx.): 220 g(including the cable)
GENERAL
Channel coverage:
Australia VHF: ch 0 –12 UHF: ch 28 –69
New Zealand VHF: ch 1 –11 UHF: ch 21 –69
Indonesia VHF: ch 1A –11 UHF: ch 21 –69
CCIR VHF: ch 2 –12 UHF: ch 21 –69
Power requirement
Operating voltage: DC 14.4 V (11 V to 16 V allowance)
Grounding system: Negative ground
Allowable operating temperature: 0°C to +40°C
Design and specifications subject to change without notice.
Connecting the remote sensor unit
•When used with any other monitor system than KD-AV7008.
•Before installing, make sure the remote controller functions properly with the remote
sensor unit placed in your selected position.
•
Wipe clean the selected area sufficiently, and affix the remote sensor unit to the place firmly
after removing the protective sheet from the double-faced adhesive tape.
•Avoid any area on the dashboard, etc. subjected to direct sunlight.
Select an area where the remote sensor unit can receive remote signals through its
front face (sensing area).
Dashboard, etc
*2